MrMeeb/snmp_mib_archive
1
0
Fork 0
mirror of https://github.com/hsnodgrass/snmp_mib_archive.git synced 2025-04-18 00:13:02 +00:00
Code Issues Actions Packages Projects Releases Wiki Activity
snmp_mib_archive/CISCO-WAN-ATM-CONN-MIB.my
Heston Snodgrass 89bf4b016e initial commit
2016-12-15 15:03:18 -07:00

2449 lines
97 KiB
Plaintext
Raw Blame History

-- *****************************************************************
-- CISCO-WAN-ATM-CONN-MIB.my: CISCO MSSBU ATM connection MIB
--
-- July 2002, muthumayan
--
-- Copyright (c) 1998-2003 by cisco Systems, Inc.
-- All rights reserved.
--
-- *****************************************************************
--
-- SPVC provisioning Model
-- =======================
--
-- To use this MIB it is essential to understand the provisioning
-- model employed in MGX8800 Series products. This provisioning model
-- was designed considering the multiple types of services such as
-- frame relay,circuit emulation, voice etc. that need to be supported.
--
-- To start with, the connection termination points are termed
-- `endpoints'. These endpoints derive their characteristics from
-- from the type of service they handle. Thus frame relay endpoints
-- are characterised by a frame relay identifier (DLCI) and the
-- committed frame rate and so on. The endpoints could also
-- terminate an ATM interface.
--
-- The connection between these endpoints is a switched ATM virtual
-- circuit (SVC). The routing of a connection within an ATM network
-- is handled by a network `controller' e.g PNNI.
--
-- From a user perspective, the endpoint is identified by:
-- * physical entities: nodename, shelf, slot, physical line
-- * logical entities : this could be a DLCI in a frame relay.
-- or a T1 slot number in a voice card
-- or a VPI/VCI in an ATM card.
--
-- We term the above identifiers as `user addresses'. There is yet
-- another set of addresses that define the endpoints within an
-- ATM network. This is the address of the endpoint, as known to
-- the network controller and hence termed `network address'.
-- The network address is assigned by the switch (MGX) when a
-- user provisions an endpoint. The network address is of little
-- significance from the user's perspective, but is mandatory for
-- routing a connection. The network address in this ATM network
-- is a combination of an NSAP address (a 20 octet number uniquely
-- identifying a logical interface) and a VPI/VCI within this
-- interface.
--
-- In any switched network, there is always a `calling' and a
-- `called' party. Likewise in the ATM network, one endpoint is
-- responsible for setting up the connection (making a call).
-- This endpoint is termed the `master' endpoint, the other one
-- being the slave. To route a call from the master to slave, the
-- master endpoint needs to know the `network' address of the
-- slave endpoint. And this information needs to be conveyed
-- when provisioning a master endpoint.
--
-- This imposes a sequence in provisioning a connection:
-- * The NMS first adds the slave endpoint. The slave endpoint's
-- user address is specified during the add operation. The
-- switch assigns a network address to this added endpoint.
-- * NMS gets the slave's network address from switch.
-- * NMS adds the master endpoint. The master's user address
-- is specified, along with the slave's network address.
-- * SPVC provisioning is deemed successful, only if both the
-- endpoints are added. The routing of the connection takes
-- place only after the master endpoint is added.
--
-- *****************************************************************
CISCO-WAN-ATM-CONN-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Integer32, Unsigned32
FROM SNMPv2-SMI
RowStatus,TruthValue,
TEXTUAL-CONVENTION FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF
ifIndex FROM IF-MIB
ciscoWan FROM CISCOWAN-SMI;
ciscoWanAtmConnMIB MODULE-IDENTITY
LAST-UPDATED "200303300000Z"
ORGANIZATION "Cisco Systems, Inc."
CONTACT-INFO
" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-wanatm@cisco.com"
DESCRIPTION
"This MIB is used for configuring/provisioning SPVCs on
the ATM interfaces. This is used for ATM switch
connection management.
Terminologies used:
GCRA - The Generic Cell Rate Algorithm(GCRA) is used to
define comformance with repect to the traffic
contract.For each cell arrival, the GCRA determines
whether the cell conforms to the traffic contract
of the connection.
PCR - The Peak Cell Rate(PCR) traffic parameter specifies
an upper bound on the rate at which traffic can
be submitted on an ATM connection.
SCR - Sustained Cell Rate.
MBS - Maximum Burst Size.
MCR - Minimum Cell Rate is the rate at which the source
is always allowed to send.
ACR - Allowed Cell Rate is the current rate at which
a source is allowed to send.
RDF - Rate Decrease Factor controls the decrease in the
cell transmission rate
CRM - Missing RM-cell count. CRM limits the number of
forward RM-cells which may be sent in the absence
of received backward RM-cells.
CDF - The Cutoff Decrease Factor controls the decrease
in ACR assoicated with the CRM.
CDVT - Cell Delay Transfer Variation Tolerance
CBR - The Constant Bit Rate(CBR) service category is used
by connections that request a static amount of
bandwidth that is continuously available during the
connection lifetime. This amount of bandwidth is
characterized by a PCR value.
rt-VBR - The real-time Variable Bit Rate(rt-VBR) service
category is intended for real-time applications,
i.e.,those requiring tightly constrainded delay
and delay variation, as would be appropriate for
voice and video applications.The rt-VBR connections
are characterized in terms of a PCR, SCR and MBS.
nrt-VBR - The non-real-time Variable Bit Rate(nrt-VBR)
service category is intended for non-real-time
applications which have bursty traffic
characteristics. The nrt-VBR is characterized
in terms of a PCR,SCR and MBS.
UBR - The Unspecified Bit Rate(UBR) service category is
intended for non-real-time applications,i.e.,those
not requiring tightly constrained delay and delay
variation. The UBR service does not specify traffic
related service gurantees. The UBR service is
indicated by use of the Best Effort Indicator in
ATM User Cell Rate Information element.
ABR - The Available Bit Rate(ABR) is an ATM layer
service category for which the limiting ATM layer
transfer characteristics provided by the network
may change subsequent to connection establishment.
CAC - The Connection Admission Control(CAC) function is
defined as the set of actions taken by the network
at SVC establishment or by network management during
PVC establishment in order to determine whether
a connection can be progressed or should be rejected.
UPC - Usage Parameter Control(UPC) is defined as the set
of actions taken by the network to monitor and
control traffic.
"
REVISION "200303300000Z"
DESCRIPTION "a) MAX-ACCESS clauses of objects in cwAtmChanTestTable
are changed from read-create to read-write
since this table does not have RowStaus object.
"
REVISION "200209180000Z"
DESCRIPTION "a) Added following objects in cwAtmChanCnfgTable:
cwaChanP2MP
b) The DESCRIPTION of following objects are
updated as a result of adding
'cwaChanP2MP' object:
'cwaChanRemoteVpi', 'cwaChanRemoteVci',
'cwaChanRemoteNSAPAddr', 'cwaChanRemotePCR',
'cwaChanRemoteMCR', 'cwaChanRemoteSCR',
'cwaChanRemoteCDV', 'cwaChanRemoteCTD',
'cwaChanRemoteMBS', 'cwaChanRemoteCDVT',
'cwaChanRemotePercentUtil', 'cwaChanRemoteCLR'
and 'cwaChanSlaveType'
c) Importing Unsigned32 from SNMPv2-SMI.
d) Added 'cwGlobalChanDataTable' Table.
e) Added following objects in cwAtmChanCnfgTable:
cwaChanPrefRouteId
cwaChanDirectRoute
"
REVISION "200203240000Z"
DESCRIPTION "a) Added following objects in cwAtmChanCnfgTable:
cwaChanSlaveType
cwaChanRoutingPriority.
b) Added following objects under cwAtmChanInformation:
cwaChanNumVPCsInAlarm
cwaChanNumVCCsInAlarm.
c) Clarified the ifIndex usage in DESCRIPTION of
cwAtmChanCnfgEntry.
d) Updated the DESCRIPTION of following objects:
cwaChanServiceCategory
cwaChanVpcFlag
cwaChanIdentifier
cwaChanRowStatus
e) Modified the range from 0..100 to 1..100 for
following objects:
cwaChanPercentUtil
cwaChanRemotePercentUtil.
f) Deprecated following objects:
cwaChanAbrERS
cwaChanAisIWCapability
"
REVISION "200102090000Z"
DESCRIPTION "Update description for cwaChanVpcFlag,
cwaChanStatsEnable,
cwaChanRoutingMastership, and cwaChanAbrVSVDEnable"
REVISION "200101030000Z"
DESCRIPTION "Change description to indicate that cwaChanCDV,
cwaChanCTD, cwaChanRemoteCDV, cwaChanRemoteCTD and
cwaChanMaxCost parameters cannot be set on a
slave endpoint."
REVISION "200011150000Z"
DESCRIPTION "Added cwaChanOamSegEpEnable object in
cwAtmChanCnfgTable."
REVISION "200007170000Z"
DESCRIPTION "Deprecated object cwaChanRemoteCDVT"
REVISION "200006190000Z"
DESCRIPTION "Initial version of the MIB"
::= { ciscoWan 1 }
cwConnMibObjects OBJECT IDENTIFIER ::= { ciscoWanAtmConnMIB 1 }
cwAtmChanCnfg OBJECT IDENTIFIER ::= { cwConnMibObjects 1 }
cwAtmChanState OBJECT IDENTIFIER ::= { cwConnMibObjects 2 }
cwAtmChanTest OBJECT IDENTIFIER ::= { cwConnMibObjects 3 }
cwAtmChanInformation OBJECT IDENTIFIER ::= { cwConnMibObjects 4 }
cwGlobalChanDataGroup OBJECT IDENTIFIER ::= { cwConnMibObjects 5 }
-- ----------------------------------------------------------------------------
-- TEXTUAL CONVENTIONS USED IN THIS MIB
-- ----------------------------------------------------------------------------
CiscoAtmServiceCategory ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The ATM forum service categories.
For sake of backward compatibility with UNI3.1, two CBR
service types cbr2 and cbr3 have been added.
"
REFERENCE "ATM Forum Traffic Management Specification Version 4.0
Section 4.5.4"
SYNTAX INTEGER {
cbr1(1),
vbr1RT(2),
vbr2RT(3),
vbr3RT(4),
vbr1nRT(5),
vbr2nRT(6),
vbr3nRT(7),
ubr1(8),
ubr2(9),
abr(10),
cbr2(11),
cbr3(12)
}
CiscoWanLpbkTypes ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Defines possible loopback configurations for a connection:
noLoopback : no loopback or clear configured loopback
destructive : loopback all cells, causing data disruption.
nonDestructive: loopback performed using OAM loopback cells.
Does not disrupt regular traffic."
SYNTAX INTEGER {
noLpbk(1),
destructive(2),
nonDestructive(3)
}
CiscoWanLpbkDir ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Direction in which looped should be effected:
external : loop port traffic back to port. Applicable
only for destructive mode.
internal : loop switch's egress traffic back to switch.
Applicable only for destructive mode.
forward : inject OAM loopback cells towards the
switching fabric (ingress). Applicable only
for non-destructive mode.
reverse : inject OAM loopback cells towards the
port (egress). Applicable only for non-
destructive mode."
SYNTAX INTEGER {
external(1),
internal(2),
forward(3),
reverse(4)
}
CiscoWanTestStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Defines possible loopback test status at an endpoint."
SYNTAX INTEGER {
noStatus (1),
lpbkInProgress(2),
lpbkSuccess(3),
lpbkAbort(4),
lpbkTimeOut(5),
lpbkInEffect(6)
}
CiscoWanOperStatus ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Defines operational status of an endpoint"
SYNTAX INTEGER {
operOk(1),
operFail(2),
adminDown(3)
}
CiscoWanNsapAtmAddress ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"ATM address used by the networking entity. The only
address type presently supported is NSAP (20 octets)"
SYNTAX OCTET STRING (SIZE(20))
CiscoWanAlarmState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Defines possible alarms at an endpoint:
ingAisRdi : Endpoint receiving AIS or RDI cells
in ingress direction
egrAisRdi : Endpoint receiving AIS or RDI cells
in egress direction
conditioned : Networking entity has forced the
endpoint out of service. This could
be attributed to either routing
failure or to a maintenance operation
initiated by the networking entity.
interfaceFail : The interface to which this connection
belongs has failed.
ccFail : The OAM continuity check between the
connection and its peer endpoint has
detected a failure.
mismatch : connection exists in SM database, but
not in the network controller database
ingAbitFail : Feeder connection detects A-bit failure
in the ingress direction.
Each of the alarm conditions is represented as a bit of an
integer. Hence a value of zero indicates that there are no
alarms."
SYNTAX INTEGER {
ingAisRdi (1),
egrAisRdi (2),
conditioned (4),
interfaceFail(8),
ccFail(16),
mismatch (32),
ingAbitFail (64)
}
CiscoWanXmtState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Defines possible transmit states of an endpoint:
normal : Endpoint transmitting normal traffic.
sendingAIS : Endpoint inhibits regular traffic,
sends AIS on egress
sendingRDI : Endpoint inhibits regular traffic,
sends AIS on egress"
SYNTAX INTEGER {
normal(1),
sendingAIS(2),
sendingRDI(3)
}
CiscoWanRcvState ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Defines possible receive states of an endpoint
normal : Endpoint receiving normal traffic.
receivingAIS : Endpoint receiving AIS, in either
ingress/egress
receivingRDI : Endpoint receiving RDI, in either
ingress/egress
ccFailure : Endpoint does not receive OAM CC cells"
SYNTAX INTEGER {
normal(1),
receivingRDI(2),
receivingAIS(3),
ccFailure(4)
}
CiscoWanERSConfg ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Defines possible configuration for Explicit Rate Stamping (ERS):
None : Disable the ERS on connection
enableIngress : Enable ERS in the Ingress direction ONLY
enableEgress : Enable ERS in the Engress direction ONLY
enableBoth : Enable ERS in both direction"
SYNTAX INTEGER {
none(1),
enableIngress(2),
enableEgress(3),
enableBoth(4)
}
CiscoWanVSVDConfg ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Defines possible VSVD configuration applicable to an endpoint:
vsvdOff : Disable VSVD
vsvdOn : Enable VSVD
switchDefault : Use default settings on switch."
SYNTAX INTEGER {
vsvdOff(1),
vsvdOn(2),
switchDefault(3)
}
CiscoWanAisIW ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Defines an SPVC endpoint's AIS capability:
e2eAisCapable : Endpoint capable of detecting/generating
e2e AIS.
segAisCapable : Endpoint capable of detecting/generating seg
AIS."
SYNTAX INTEGER {
e2eAisCapable(1),
segAisCapable(2)
}
AbrRateFactors ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Defines possible rate factors to be used in
increasing/decreasing ABR cell rate."
SYNTAX INTEGER {
oneOver32768(1),
oneOver16384(2),
oneOver8192(3),
oneOver4096(4),
oneOver2048(5),
oneOver1024(6),
oneOver512(7),
oneOver256(8),
oneOver128(9),
oneOver64(10),
oneOver32(11),
oneOver16(12),
oneOver8(13),
oneOver4(14),
oneOver2(15),
one(16)
}
-- ------------------------------------------------------------------------
-- Channel configuration group : Contains all objects required for
-- configuring a SPVC on a ATM Capable Service Module.
-- ------------------------------------------------------------------------
cwAtmChanCnfgTable OBJECT-TYPE
SYNTAX SEQUENCE OF CwAtmChanCnfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains mandatory endpoint configuration
for all SPVC connections.Most of the objects in this
table are applicable to all provisioned endpoints for all
service categories. The objects cwaChanAbrZZZ however,
provide additional configuration information which apply
to ABR endpoints only.
Routing parameters 'cwaChanCDV', 'cwaChanCTD',
'cwaChanRemoteCDV', 'cwaChanRemoteCTD' and
'cwaChanMaxCost' cannot be set
on a slave endpoint(i.e.if 'cwaChanRoutingMastership'
is set to 'false')."
::= { cwAtmChanCnfg 1 }
cwAtmChanCnfgEntry OBJECT-TYPE
SYNTAX CwAtmChanCnfgEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the cwAtmChanCnfgTable. The each entry
corresponds to a connection endpoint identified
by interface(ifIndex),Virtual Path Identifier(VPI)
and Virtual Channel Identifier(VCI). The ifIndex
is for those entries in ifTable identified by
ifType values atmVirtual(149) and propAtm(197)."
INDEX { ifIndex, cwaChanVpi, cwaChanVci }
::= { cwAtmChanCnfgTable 1 }
CwAtmChanCnfgEntry ::=
SEQUENCE {
cwaChanVpi Unsigned32,
cwaChanVci Unsigned32,
cwaChanServiceCategory CiscoAtmServiceCategory,
cwaChanVpcFlag TruthValue,
cwaChanIdentifier Unsigned32,
cwaChanUploadCounter Unsigned32,
cwaChanStatsEnable TruthValue,
cwaChanCCEnable TruthValue,
cwaChanLocalVpi Unsigned32,
cwaChanLocalVci Unsigned32,
cwaChanLocalNSAPAddr CiscoWanNsapAtmAddress,
cwaChanRemoteVpi Unsigned32,
cwaChanRemoteVci Unsigned32,
cwaChanRemoteNSAPAddr CiscoWanNsapAtmAddress,
cwaChanControllerId Unsigned32,
cwaChanRoutingMastership TruthValue,
cwaChanMaxCost Unsigned32,
cwaChanReroute TruthValue,
cwaChanFrameDiscard TruthValue,
cwaChanOperStatus CiscoWanOperStatus,
cwaChanPCR Unsigned32,
cwaChanMCR Unsigned32,
cwaChanSCR Unsigned32,
cwaChanCDV Unsigned32,
cwaChanCTD Unsigned32,
cwaChanMBS Unsigned32,
cwaChanCDVT Unsigned32,
cwaChanPercentUtil Unsigned32,
cwaChanRemotePCR Unsigned32,
cwaChanRemoteMCR Unsigned32,
cwaChanRemoteSCR Unsigned32,
cwaChanRemoteCDV Unsigned32,
cwaChanRemoteCTD Unsigned32,
cwaChanRemoteMBS Unsigned32,
cwaChanRemoteCDVT Unsigned32,
cwaChanRemotePercentUtil Unsigned32,
cwaChanAbrICR Unsigned32,
cwaChanAbrADTF Unsigned32,
cwaChanAbrRDF AbrRateFactors,
cwaChanAbrRIF AbrRateFactors,
cwaChanAbrNRM INTEGER,
cwaChanAbrTRM INTEGER,
cwaChanAbrCDF INTEGER,
cwaChanAbrFRTT Unsigned32,
cwaChanAbrTBE Unsigned32,
cwaChanAbrERS CiscoWanERSConfg,
cwaChanAbrVSVDEnable TruthValue,
cwaChanRowStatus RowStatus,
cwaChanIntAbrVSVD CiscoWanVSVDConfg,
cwaChanExtAbrVSVD CiscoWanVSVDConfg,
cwaChanAisIWCapability CiscoWanAisIW,
cwaChanCLR Unsigned32,
cwaChanRemoteCLR Unsigned32,
cwaChanOamSegEpEnable INTEGER,
cwaChanSlaveType INTEGER,
cwaChanRoutingPriority Integer32,
cwaChanP2MP TruthValue,
cwaChanPrefRouteId Integer32,
cwaChanDirectRoute TruthValue
}
cwaChanVpi OBJECT-TYPE
SYNTAX Unsigned32 (0..4095)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VPI value of a VP or VC connection. The cwaChanVpcFlag
serves to distinguish if this is a VP/VC connection"
::= { cwAtmChanCnfgEntry 1 }
cwaChanVci OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VCI value of VC connection. The cwaChanVpcFlag serves
to distinguish if this is a VP/VC connection. For a VPC,
the VCI is irrelevant and is set to a value of 0"
::= { cwAtmChanCnfgEntry 2 }
cwaChanServiceCategory OBJECT-TYPE
SYNTAX CiscoAtmServiceCategory
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object identifies the service type to which
this connection belongs. The service type specified
is one among the ATM forum service types and
implicitly determines the configuration for GCRA.
This Object can be set only during row creation."
::= { cwAtmChanCnfgEntry 3 }
cwaChanVpcFlag OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indentifies if the endpoint is a
VP/VC endpoint. For a VPC, this object is set to
true(1); For a VCC, this object is set to false(2).
This Object can be set only during row creation."
::= { cwAtmChanCnfgEntry 4 }
cwaChanIdentifier OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This number represents a RESOURCE at the switch that
has been assigned for this connection (identified
by ifIndex, cwaChanVpi and cwaChanVci). An example of this
resource could be the LCN/GLCN used by the switch. Another
example could be a record number assigned for this connection
in a database of records.
When a connection gets deleted, this resource gets
released into a free pool. When a new endpoint is added
(different ifIndex, cwaChanVpi & cwaChanVci), the switch may
re-assign this resource.
Thus all connections in a switch would have an unique
cwaChanIdentifier. Since the number of resources in the
switch is a much lesser subset as compared to all possible
combinations of ifIndex, vpi and vci, this number serves as
a quick reference index between the switch and the NMS.
This is especially useful during the configuration upload
of connections from the switch to the NMS."
::= { cwAtmChanCnfgEntry 5 }
cwaChanUploadCounter OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter tracks the number of configuration changes
that happen on a specific endpoint (identified by ifIndex,
cwaChanVpi, and cwaChanVci).
The value of this object is derived from
cwChanGlobalTransactionId. For every connection changes
(add/delete/modify/up/down), the value of
cwChanGlobalTransactionId is incremented and that value
is used for this object.
This counter is used by the NMS to determine if a connection
configuration had been modified and requires an upload."
::= { cwAtmChanCnfgEntry 6 }
cwaChanStatsEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Limits imposed by software or hardware implementations
could restrict the amount of statistical data that can be
maintained in a physical entity (like a service module card).
Hence there could be a need to restrict statistics collection
to a smaller subset.
This object serves the purpose of enabling/disabling statistics
collection on a per connection basis. In implementations which
do not have such limitations, this object can be set to true(1)
for all connections.
When set to true(1), statistics collection is enabled;
When set to false(2), stats collection is disabled"
DEFVAL { false }
::= { cwAtmChanCnfgEntry 7 }
cwaChanCCEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object serves to enable or disable continuity check(CC)
on a connection endpoint. When continuity check is enabled
on an endpoint, the endpoint anticipates OAM CC cells from its
peer endpoint. OAM CC cells are sent when the peer endpoint
does not have traffic cells to send. If the connection is
idle and this endpoint has not received OAM CC cells for a
period of 3.5 +/- 0.5 seconds, it declares continuity failure.
This object serves to administratively control the CC feature.
Typical implementations (of this feature) may choose to ignore
this control or impose other conditions to actually enable CC
cell flow. However, if this object is set to false(2), then this
feature should be disabled"
DEFVAL { false }
::= { cwAtmChanCnfgEntry 8 }
cwaChanLocalVpi OBJECT-TYPE
SYNTAX Unsigned32 (0..4095)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the internal VPI assigned to a local
endpoint, by the switch. The cwaChanLocalVpi, cwaChanLocalVci
and the cwaChanLocalNSAPAddr, form a unique identifier for
the connection endpoint in the networking domain"
::= { cwAtmChanCnfgEntry 9 }
cwaChanLocalVci OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the internal VCI assigned to a local
endpoint, by the switch. The cwaChanLocalVpi, cwaChanLocalVci
and the cwaChanLocalNSAPAddr, form a unique identifier for
the connection endpoint in the networking domain"
::= { cwAtmChanCnfgEntry 10 }
cwaChanLocalNSAPAddr OBJECT-TYPE
SYNTAX CiscoWanNsapAtmAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the internal NSAP assigned to a local
endpoint, by the switch. The cwaChanLocalVpi, cwaChanLocalVci
and the cwaChanLocalNSAPAddr, form a unique identifier for
the connection endpoint in the networking domain"
::= { cwAtmChanCnfgEntry 11 }
cwaChanRemoteVpi OBJECT-TYPE
SYNTAX Unsigned32 (0..4095)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object identifies the VPI of the peer endpoint. The
cwaChanRemoteVpi, cwaChanRemoteVpi and the
cwaChanRemoteNSAPAddr, identify the peer endpoint in
the networking domain.
If the object 'cwaChanP2MP' is set to 'true', this object
should not be 'set' and the value
of this object, if any, is not meaningful.
This Object can be set only during row creation."
::= { cwAtmChanCnfgEntry 12 }
cwaChanRemoteVci OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object identifies the VCI of the peer endpoint. The
cwaChanRemoteVpi, cwaChanRemoteVpi and the
cwaChanRemoteNSAPAddr, identify the peer endpoint in
the networking domain.
If the object 'cwaChanP2MP' is set to 'true', this object
should not be 'set' and the value
of this object, if any, is not meaningful.
This Object can be set only during row creation."
::= { cwAtmChanCnfgEntry 13 }
cwaChanRemoteNSAPAddr OBJECT-TYPE
SYNTAX CiscoWanNsapAtmAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object identifies the NSAP of the peer endpoint. The
cwaChanRemoteVpi, cwaChanRemoteVpi and the
cwaChanRemoteNSAPAddr, identify the peer endpoint in
the networking domain.
If the object 'cwaChanP2MP' is set to 'true', this object
should not be 'set' and the value
of this object, if any, is not meaningful.
This Object can be set only during row creation."
::= { cwAtmChanCnfgEntry 14 }
cwaChanControllerId OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object serves to associate an endpoint with a specific
controller. Usually resource partitioning makes the association
between a controller and a range of vpi-vci. There could be
switches where hard partitioning of vpi-vci may not be
implemented, in which case this object serves to tie a
specific vpi-vci to a controller.
This object can not be modified after the row is created."
::= { cwAtmChanCnfgEntry 15 }
cwaChanRoutingMastership OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object, if set to true(1) identifies that this endpoint
as the `master' endpoint of the connection. When set to false(2)
this identifies the `slave' endpoint of the connection. The
slave endpoint is the called party, while the master endpoint
is the calling party in the SPVC call setup. The networking
entity initiates routing of a SPVC connection only after a
master endpoint is added. Mastership of a SPVC cannot be
changed, once provisioned, implying that this object can
be set only during row creation."
DEFVAL { false }
::= { cwAtmChanCnfgEntry 16 }
cwaChanMaxCost OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used by the networking entity to select a route
based on administrative weight of possible routes.
Administrative weights of links and nodes contained in a path
are aggregated and compared against this object. The networking
entity prefers a path whose aggregate administrative weight is
lesser than the value of this object.
Setting this parameter to 0 indicates to the switch that only
the best available route should be chosen. If this
object is set to a value of 0xFFFFFFFF(4294967295),
then switch ignore this metric in making routing decisions.
This parameter is not allowed to be set on a slave endpoint.
(i.e. if 'cwaChanRoutingMastership' is set to 'false')."
DEFVAL { 'FFFFFFFF'h }
::= { cwAtmChanCnfgEntry 17 }
cwaChanReroute OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is used by the administrator to trigger the
re-routing of the connection.
* Rerouting takes effect, when this object is set to true(1).
When set to false(2), no action is taken.
* A get on this object always returns false(2).
* When this object is set, no other object other than the
RowStatus should be set in the MIB.
* Reroute can be triggered only from the master endpoint.
Any attempt to trigger reroute from the slave endpoint would
result in a failure of the SET operation. "
DEFVAL { false }
::= { cwAtmChanCnfgEntry 18 }
cwaChanFrameDiscard OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"When set to true(1), enables the frame discard feature
for the connection. This is applicable only to the master
endpoint (cwaChanRoutingMastership is true) and only for
VCC connections."
DEFVAL { false }
::= { cwAtmChanCnfgEntry 19 }
cwaChanOperStatus OBJECT-TYPE
SYNTAX CiscoWanOperStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Reflects operational status of an endpoint.
* This object is set to operFail(2), if the connection is
not routed or if the endpoint receives AIS/RDI or if there
is a CC failure.
* If the connection is administratively down, this object
would be set to adminDown(3).
* For a normal case, this is set to operOk(1)"
::= { cwAtmChanCnfgEntry 20 }
cwaChanPCR OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "cells per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Peak cell rate (PCR) for the direction local -> remote"
::= { cwAtmChanCnfgEntry 21 }
cwaChanMCR OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "cells per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum cell rate (MCR) for the direction local -> remote"
::= { cwAtmChanCnfgEntry 22 }
cwaChanSCR OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "cells per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Sustainable cell rate (SCR) for the direction local -> remote"
::= { cwAtmChanCnfgEntry 23 }
cwaChanCDV OBJECT-TYPE
SYNTAX Unsigned32 (0..16777215)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum tolerable cell delay variation in the direction
local -> remote.
Setting this parameter to 0xFFFFFF(16777215) indicates to
the switch that this parameter does not have significance
in SPVC call setup.
This parameter is not allowed to be set on a slave endpoint.
(i.e. if 'cwaChanRoutingMastership' is set to 'false')."
DEFVAL { 'FFFFFF'h }
::= { cwAtmChanCnfgEntry 24 }
cwaChanCTD OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum tolerable network transfer delay in the
direction local -> remote.
Setting this parameter to 0xFFFF(65535) indicates to the
switch that this parameter does not have significance in
SPVC call setup.
This parameter is not allowed to be set on a slave endpoint.
(i.e. if 'cwaChanRoutingMastership' is set to 'false')."
DEFVAL { 'FFFF'h }
::= { cwAtmChanCnfgEntry 25 }
cwaChanMBS OBJECT-TYPE
SYNTAX Unsigned32 (0..5000000)
UNITS "cells"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Burst Size (MBS) used in the direction local -> remote"
REFERENCE
"ATM Forum Traffice Management Specification Version 4.0
Annex C"
::= { cwAtmChanCnfgEntry 26 }
cwaChanCDVT OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Cell delay variation tolerance(CDVT) used in the direction
local -> remote.
Setting this parameter to 0xFFFFFFFF(4294967295) indicates to
the switch that it may use a default value of CDVT"
REFERENCE
"ATM Forum Traffice Management Specification Version 4.0
Annex C"
DEFVAL { 'FFFFFFFF'h }
::= { cwAtmChanCnfgEntry 27 }
cwaChanPercentUtil OBJECT-TYPE
SYNTAX Unsigned32 (1..100)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This factor provides a per connection control
for overbooking bandwidth. This is used in
conjunction with the VSI interface policy while
performing CAC. This is applied for the direction
local -> remote"
DEFVAL { 100 }
::= { cwAtmChanCnfgEntry 28 }
cwaChanRemotePCR OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "cells per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Peak cell rate (PCR) for the direction remote -> local.
If the object 'cwaChanP2MP' is set to 'true', this object
should not be 'set' and the value
of this object, if any, is not meaningful."
::= { cwAtmChanCnfgEntry 29 }
cwaChanRemoteMCR OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "cells per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum cell rate for the direction remote -> local"
::= { cwAtmChanCnfgEntry 30 }
cwaChanRemoteSCR OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "cells per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Sustainable cell rate for the direction remote -> local"
::= { cwAtmChanCnfgEntry 31 }
cwaChanRemoteCDV OBJECT-TYPE
SYNTAX Unsigned32 (0..16777215)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum tolerable cell delay variation for the direction
remote -> local.
Setting this parameter to 0xFFFFFF(16777215) indicates to
the switch that this parameter does not have significance
in SPVC call setup.
This parameter is not allowed to be set on a slave endpoint.
(i.e. if 'cwaChanRoutingMastership' is set to 'false')."
DEFVAL { 'FFFFFF'h }
::= { cwAtmChanCnfgEntry 32 }
cwaChanRemoteCTD OBJECT-TYPE
SYNTAX Unsigned32 (0..65535)
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum tolerable network transfer delay in the
direction direction remote -> local.
Setting this parameter to 0xFFFF(65535) indicates to the switch
that this parameter does not have significance in SPVC call
setup.
This parameter is not allowed to be set on a slave endpoint.
(i.e. if 'cwaChanRoutingMastership' is set to 'false').
If the object 'cwaChanP2MP' is set to 'true', this object
should not be 'set' and the value
of this object, if any, is not meaningful."
DEFVAL { 'FFFF'h }
::= { cwAtmChanCnfgEntry 33 }
cwaChanRemoteMBS OBJECT-TYPE
SYNTAX Unsigned32 (0..5000000)
UNITS "cells"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Burst Size (MBS) used in the direction remote -> local.
If the object 'cwaChanP2MP' is set to 'true', this object
should not be 'set' and the value
of this object, if any, is not meaningful."
REFERENCE
"ATM Forum Traffice Management Specification Version
4.0 Annex C."
::= { cwAtmChanCnfgEntry 34 }
cwaChanRemoteCDVT OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "cells"
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Cell delay variation tolerance(CDVT) used in the direction
remote -> local.
Setting this parameter to 0xFFFFFFFF(4294967295) indicates
to the switch that it may use a default value of CDVT.
If the object 'cwaChanP2MP' is set to 'true', this object
should not be 'set' and the value
of this object, if any, is not meaningful."
REFERENCE
"ATM Forum Traffice Management Specification Version 4.0 Annex C"
DEFVAL { 'FFFFFFFF'h }
::= { cwAtmChanCnfgEntry 35 }
cwaChanRemotePercentUtil OBJECT-TYPE
SYNTAX Unsigned32 (1..100)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This factor provides a per connection control
for overbooking bandwidth. This is used in
conjunction with the VSI interface policy while
performing CAC. This is applied for the direction
remote -> local.
If the object 'cwaChanP2MP' is set to 'true', this object
should not be 'set' and the value
of this object, if any, is not meaningful."
DEFVAL { 100 }
::= { cwAtmChanCnfgEntry 36 }
cwaChanAbrICR OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "cells/sec"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Initial cell rate: Rate at which a source should send initially
after an idle period. The value must not be larger than the PCR"
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
::= { cwAtmChanCnfgEntry 37 }
cwaChanAbrADTF OBJECT-TYPE
SYNTAX Unsigned32 (1..1023)
UNITS "10 milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"ACR Decrease Time Factor. This is the time permitted between
sending RM-cells (Resource Mangement Cells) before the rate is
decreased to ICR (Initial Cell Rate)."
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
::= { cwAtmChanCnfgEntry 38 }
cwaChanAbrRDF OBJECT-TYPE
SYNTAX AbrRateFactors
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Decrease Factor: Controls the rate decrease which occurs
when backward RM-cells with CI=1 are received. Larger values
lead to faster rate decrease.
This factor is applied at both the local and remote endpoints,
thus making the loop control symmetrical. Backward RM cells at
the local endpoint correspond to RM cells received in the
remote->local direction. Backward RM cells at the remote
endpoint correspond to RM cells received in the local->remote
direction."
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
::= { cwAtmChanCnfgEntry 39 }
cwaChanAbrRIF OBJECT-TYPE
SYNTAX AbrRateFactors
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Increase Factor: Controls the rate increase which occurs
when a backward RM-cell is received with CI=0 and NI=0. Larger
values lead to faster rate increase
This factor is applied at both the local and remote endpoints,
thus making the loop control symmetrical. Backward RM cells at
the local endpoint correspond to RM cells received in the
remote->local direction. Backward RM cells at the remote
endpoint correspond to RM cells received in the local->remote
direction."
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
::= { cwAtmChanCnfgEntry 40 }
cwaChanAbrNRM OBJECT-TYPE
SYNTAX INTEGER {
nrm2(1),
nrm4(2),
nrm8(3),
nrm16(4),
nrm32(5),
nrm64(6),
nrm128(7),
nrm256(8)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum number of cells a source may send for each forward
RM-cell"
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
::= { cwAtmChanCnfgEntry 41 }
cwaChanAbrTRM OBJECT-TYPE
SYNTAX INTEGER {
trm0point78125(1),
trm1point5625(2),
trm3point125(3),
trm6point25(4),
trm12point5(5),
trm25(6),
trm50(7),
trm100(8)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Upper bound on the time between forward RM-cells for an
active source (in milliseconds)"
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
::= { cwAtmChanCnfgEntry 42 }
cwaChanAbrCDF OBJECT-TYPE
SYNTAX INTEGER {
cdf0(1),
cdfOneOver64(2),
cdfOneOver32(3),
cdfOneOver16(4),
cdfOneOver8(5),
cdfOneOver4(6),
cdfOneOver2(7),
cdfOne(8)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Cutoff Decrease Factor: Controls the rate decrease associated
with lost or delayed backward RM cells. Larger values result in
faster rate decrease"
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
::= { cwAtmChanCnfgEntry 43 }
cwaChanAbrFRTT OBJECT-TYPE
SYNTAX Unsigned32 (0..16700000)
UNITS "microseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Fixed round trip time: Sum of the fixed propagation delays from
the source to a destination network."
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
::= { cwAtmChanCnfgEntry 44 }
cwaChanAbrTBE OBJECT-TYPE
SYNTAX Unsigned32 (0..16777215)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Transient Buffer Exposure. This is a negotiated number of
cells that the network would like to limit the source to
sending during startup periods, before the first RM-cell returns"
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
::= { cwAtmChanCnfgEntry 45 }
cwaChanAbrERS OBJECT-TYPE
SYNTAX CiscoWanERSConfg
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"Configuration of an endpoint for Explicit Rate Stamping.
Refer the Textual convention for possible values"
DEFVAL { none }
::= { cwAtmChanCnfgEntry 46 }
cwaChanAbrVSVDEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Abr connections require close loop control to limit the
transmission rate, depending on the network bandwidth. Now
this close loop can be end to end or between intermediate
network segments. When terminating an Abr VPL, the endpoint
needs to act like a Virtual Destination to the incoming traffic
and generate backward RM cells. While doing this it also needs
to act as a virtual source and send forward RM cells to the
real destination. This is a feature that can be enabled/disabled
under the control of this object. When set to true(1), this
feature is enabled; and is disabled when set to false(2)"
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
DEFVAL { false }
::= { cwAtmChanCnfgEntry 47 }
cwaChanRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create, modify or delete an entry
in the ciscoWanAtmChanTable.
* A row may be created using the 'CreateAndGo' option. When
the row is successfully created, the RowStatus would be
set to 'active' by the agent.
Following mandatory objects need to be specified for the
successful creation of the row(for both master and slave
endpoints):
cwaChanServiceCategory
cwaChanVpcFlag
cwaChanRoutingMastership
Following mandatory objects are needed for
creation of master endpoint:
cwaChanRemoteVpi
cwaChanRemoteVci
cwaChanRemoteNSAPAddr
* A row may be deleted by setting the RowStatus to 'destroy'.
* When there is a need to administratively down the connection,
the RowStatus could be set to 'notInService'. When the switch
completes the 'down' operation, the value of this object would
be 'notInService'.
* The connection can be made active again, by setting this
object to 'active'.
* RowStatus modification from 'notInService' to 'active' or
vice-versa will impact only the administrative status of the
connection.
* Administrative status control is limited to the master
endpoint only. The switch would reject any request for
administrative state change on the slave endpoint.
* Other options such as `CreateAndWait' will not be used."
::= { cwAtmChanCnfgEntry 48 }
cwaChanIntAbrVSVD OBJECT-TYPE
SYNTAX CiscoWanVSVDConfg
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used for enabling/disabling VSVD internal
to a segment i.e the closed loop control is in effect between
the two provisioned endpoints of the SPVC."
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
DEFVAL { switchDefault }
::= { cwAtmChanCnfgEntry 49 }
cwaChanExtAbrVSVD OBJECT-TYPE
SYNTAX CiscoWanVSVDConfg
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used for enabling/disabling VSVD external
to the segment which hosts the two endpoints of the SPVC
i.e the closed loop control will be in effect outside the
segment either towards a CPE or towards another segment."
REFERENCE
"ATM Forum Traffic Management Specification
Version 4.0 Section 5.10.2"
DEFVAL { switchDefault }
::= { cwAtmChanCnfgEntry 50 }
cwaChanAisIWCapability OBJECT-TYPE
SYNTAX CiscoWanAisIW
MAX-ACCESS read-create
STATUS deprecated
DESCRIPTION
"This object is used for achieving OAM inter-operability
between switches that cannot generate/detect segment AIS
cells. This attribute enables the newer generation of
switches to understand the OAM capability of the peer
endpoint and accordingly generate/detect seg/e2e AIS as
required. The value of this attribute is decided during
provisioning time by network management."
DEFVAL { e2eAisCapable }
::= { cwAtmChanCnfgEntry 51 }
cwaChanCLR OBJECT-TYPE
SYNTAX Unsigned32 (1..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Encoded value representing the maximum tolerable cell loss ratio
in the direction local -> remote. The actual CLR value is derived
as the negative logarithm of this value."
DEFVAL { 6 }
::= { cwAtmChanCnfgEntry 52 }
cwaChanRemoteCLR OBJECT-TYPE
SYNTAX Unsigned32 (1..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Encoded value representing the maximum tolerable cell loss ratio
in the direction remote -> local. The actual CLR value is derived
as the negative logarithm of this value.
If the object 'cwaChanP2MP' is set to 'true', this object
should not be 'set' and the value
of this object, if any, is not meaningful."
DEFVAL { 6 }
::= { cwAtmChanCnfgEntry 53 }
cwaChanOamSegEpEnable OBJECT-TYPE
SYNTAX INTEGER {
oamSegEp(1),
nonOamSegEp(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls the setting / resetting of the OAM segment
endpoint. When set to OamSegEp (1), the SPVC endpoint would
terminate all segment OAM FM cells and loopback all OAM segment
loopback cells. When set to NonOamSegEp (2), the SPVC endpoint
would be configured as a non-endpoint for OAM cells. This means
that all OAM FM cells and loopback cells would pass transparently
through this endpoint.
If this object is not specified during a SET operation, the
switch would apply a default configuration maintained for the
port."
::= { cwAtmChanCnfgEntry 54 }
cwaChanSlaveType OBJECT-TYPE
SYNTAX INTEGER {
persistentSlave(1),
nonPersistentSlave(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object indicates whether a master endpoint has a persistent
slave or not. A connection with a master and a non-persistent
slave is considered a single-ended SPVC.
This object is only meaningful when 'cwaChanRoutingMastership'
contains the value of 'true(1)'. And this variable must be used
with 'cwaChanRoutingMastership' to decide
if a connection is single-ended or not.
If the object 'cwaChanP2MP' is set to 'true', this object
should not be 'set' and the value
of this object, if any, is not meaningful."
DEFVAL {persistentSlave}
::= { cwAtmChanCnfgEntry 55 }
cwaChanRoutingPriority OBJECT-TYPE
SYNTAX Integer32(1..15)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is the routing priority of the connection. When
adding the connection, a default routing priority of 8 is used
if this is not specified. This parameter is not allowed to be
set at the slave endpoint(i.e. if 'cwaChanRoutingMastership' is
set to 'false(2)'). Any attempt to change the priority at the
slave endpoint would result in a failure of the SET operation.
A connection tagged with a routing priority of 1 is routed (and
derouted) ahead of connections tagged with other priorities."
DEFVAL {8}
::= { cwAtmChanCnfgEntry 56 }
cwaChanP2MP OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is used by the administrator to configure this master
endpoint to be the root of a point-to-multipoint
connection.
When this variable is set to 'true', this master endpoint
is the root of a point-to-multipoint connection. The
objects 'cwaChanRemoteVpi', 'cwaChanRemoteVci',
'cwaChanRemoteNSAPAddr', 'cwaChanRemotePCR', 'cwaChanRemoteMCR'
'cwaChanRemoteSCR', 'cwaChanRemoteCDV', 'cwaChanRemoteCTD',
'cwaChanRemoteMBS', 'cwaChanRemoteCDVT',
'cwaChanRemotePercentUtil', 'cwaChanRemoteCLR' and
'cwaChanSlaveType' should not be set and the
values of these objects are not meaningful.
When this variable is set to 'false', this master endpoint
is not a root of a point-to-multipoint connection.
If the object 'cwaChanPrefRouteId' is non-zero, this
object could not be set to true.
"
DEFVAL { false }
::= { cwAtmChanCnfgEntry 57 }
cwaChanPrefRouteId OBJECT-TYPE
SYNTAX Integer32(0..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object serves to to associate a preferred
route with a connection.
The value '0' means no preferred route is associated with
this connection.
Usage:
- If the value of this set to 0, the object
cwaChanDirectRoute is automatically set to FALSE by
the switch.
- The preferred route is defined in cwaPrefRouteConfTable
object.
If the object 'cwaChanP2MP' is true, this object could
not be set to a non-zero value.
"
DEFVAL { 0 }
::= { cwAtmChanCnfgEntry 58 }
cwaChanDirectRoute OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object serves to associate a prefer
route as directed route (correspond to the prefer route
object cwaChanPrefRouteId).
A directed route specifies that the associated preferred
route is the only permission route for the connection to
take. Should the associated preferred route be unavailable,
the connection is failed.
The object is not applicable if there is no associated
preferred route with the connection."
DEFVAL { false }
::= { cwAtmChanCnfgEntry 59 }
-- ------------------------------------------------------------------------
-- Channel state group : Contains all objects reflecting the state of an
-- SPVC on a ATM Capable Service Module.
-- ------------------------------------------------------------------------
cwAtmChanStateTable OBJECT-TYPE
SYNTAX SEQUENCE OF CwAtmChanStateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains channel status information for all
ATM connections configured in cwAtmChanCnfgTable."
::= { cwAtmChanState 1 }
cwAtmChanStateEntry OBJECT-TYPE
SYNTAX CwAtmChanStateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in cwAtmChanStateTable."
INDEX { ifIndex, cwaChanVpi, cwaChanVci }
::= { cwAtmChanStateTable 1 }
CwAtmChanStateEntry ::=
SEQUENCE {
cwaChanAlarmState CiscoWanAlarmState,
cwaChanEgressXmtState CiscoWanXmtState,
cwaChanEgressRcvState CiscoWanRcvState,
cwaChanIngressXmtState CiscoWanXmtState,
cwaChanIngressRcvState CiscoWanRcvState
}
cwaChanAlarmState OBJECT-TYPE
SYNTAX CiscoWanAlarmState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Defines alarms associated with an endpoint. Refer description
in the textual convention."
::= { cwAtmChanStateEntry 1 }
cwaChanEgressXmtState OBJECT-TYPE
SYNTAX CiscoWanXmtState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the state of the transmit portion of the endpoint
in the egress direction"
::= { cwAtmChanStateEntry 2 }
cwaChanEgressRcvState OBJECT-TYPE
SYNTAX CiscoWanRcvState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the state of the receive portion of the endpoint
in the egress direction"
::= { cwAtmChanStateEntry 3 }
cwaChanIngressXmtState OBJECT-TYPE
SYNTAX CiscoWanXmtState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the state of the transmit portion of the endpoint
in the ingress direction"
::= { cwAtmChanStateEntry 4 }
cwaChanIngressRcvState OBJECT-TYPE
SYNTAX CiscoWanRcvState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is the state of the receive portion of the endpoint
in the ingress direction"
::= { cwAtmChanStateEntry 5 }
-- ------------------------------------------------------------------------
-- Channel test group : Contains all objects needed for SPVC diagnostics
-- ------------------------------------------------------------------------
cwAtmChanTestTable OBJECT-TYPE
SYNTAX SEQUENCE OF CwAtmChanTestEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains configuration information for performing
connection diagnostics on ATM Connections and to obtain
results after testing"
::= { cwAtmChanTest 1 }
cwAtmChanTestEntry OBJECT-TYPE
SYNTAX CwAtmChanTestEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in cwAtmChanTestTable for each ATM Connection
endpoints."
INDEX { ifIndex, cwaChanVpi, cwaChanVci }
::= { cwAtmChanTestTable 1 }
CwAtmChanTestEntry ::=
SEQUENCE {
cwaChanTestType CiscoWanLpbkTypes,
cwaChanTestDir CiscoWanLpbkDir,
cwaChanTestIterations Unsigned32,
cwaChanTestState CiscoWanTestStatus,
cwaChanTestRoundTripDelay Unsigned32
}
cwaChanTestType OBJECT-TYPE
SYNTAX CiscoWanLpbkTypes
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures an endpoint in loopback:
This is a mandatory object.
* To configure a destructive loopback, this object needs to
be set to destructive (2). The direction in which this
destructive loopback needs to be effected, should be
specified using the cwaChanTestDir object. To de-configure
destructive loopback, this object needs to be set to
noLpbk(1).
* To configure a non-destructive loopback, this object needs
to be set to nonDestructive(3). The direction in which this
non-destructive loopback needs to be effected, should be
specified using the cwaChanTestDir object. Non-destructive
loopback gets de-configured automatically at the switch after
a certain timeout. However, if there is a need to abort
a non-destructive loopback, a set operation on this object
should be performed with a value noLpbk (1).
* Attempting to set a channel in loopback, when one is already
in progress results in a failure of the set operation (with
appropriate error code)"
DEFVAL { noLpbk }
::= { cwAtmChanTestEntry 1 }
cwaChanTestDir OBJECT-TYPE
SYNTAX CiscoWanLpbkDir
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies the direction in which loopback should be effected:
This is a mandatory object.
* For destructive loopback, this takes values external (1) and
internal (2).
* For non-destructive loopback, this takes values forward (3)
and reverse (4).
* When cwaChanTestType is noLpbk (1), this object is ignored."
::= { cwAtmChanTestEntry 2 }
cwaChanTestIterations OBJECT-TYPE
SYNTAX Unsigned32 (1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies number of loopback cells to inject. This applies to
the non-destructive mode of loopback tests only. Get operation
on this object returns the successful number of loopback
iterations performed on the endpoint."
DEFVAL { 1 }
::= { cwAtmChanTestEntry 3 }
cwaChanTestState OBJECT-TYPE
SYNTAX CiscoWanTestStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object reflects the status of the last requested test:
* If a loopback had never been effected on an endpoint,
this object reads noStatus (1).
* If a destructive mode of loopback is configured on an
endpoint, this object always reads lpbkInEffect(6).
* If a non-destructive mode of loopback is in progress, this
reads lpbkInProgress(2).
* If a non-destructive mode of loopback has completed
successfully, this reads lpbkSuccess(3).
* If a non-destructive mode of loopback has aborted, either
due to user request or switch's limitation, this reads
lpbkAbort (4).
* If a non-destructive mode of loopback has failed, this
reads lpbkTimeOut(5)."
DEFVAL { noStatus }
::= { cwAtmChanTestEntry 4 }
cwaChanTestRoundTripDelay OBJECT-TYPE
SYNTAX Unsigned32 (1..100000000)
UNITS "microseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is applicable only for non-destructive mode of
loopback. It returns the round trip delay measured during
the last non-destructive loopback test"
::= { cwAtmChanTestEntry 5 }
cwaChanNumVPCsInAlarm OBJECT-TYPE
SYNTAX Unsigned32
-- MAX-ACCESS accessible-for-notify
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of VPCs currently in
alarm.
This object is intended only in traps/notifications."
::= { cwAtmChanInformation 1 }
cwaChanNumVCCsInAlarm OBJECT-TYPE
SYNTAX Unsigned32
-- MAX-ACCESS accessible-for-notify
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the number of VCCs currently in
alarm.
This object is intended only in traps/notifications."
::= { cwAtmChanInformation 2 }
-- ------------------------------------------------------------------------
-- Global connection data group. Contains connection attributes
-- that apply globally to all provisioned connections.
-- ------------------------------------------------------------------------
cwGlobalChanDataTable OBJECT-TYPE
SYNTAX SEQUENCE OF CwGlobalChanDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains objects that are required for
configuration upload. The configuration upload
is a mechanism where the configuration(physical or
logical information)of a switch is created in
a file and that file is uploaded by the NMS application
using file transfer method(for example FTP)."
::= { cwGlobalChanDataGroup 1}
cwGlobalChanDataEntry OBJECT-TYPE
SYNTAX CwGlobalChanDataEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry containing generic information that apply to
all provisined connections(ATM/Frame Relay)."
INDEX { cwSlotIndex }
::= { cwGlobalChanDataTable 1 }
CwGlobalChanDataEntry ::=
SEQUENCE {
cwSlotIndex Unsigned32,
cwChanGlobalTransactionId Unsigned32
}
cwSlotIndex OBJECT-TYPE
SYNTAX Unsigned32 (1..429496729)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object's value generally corresponds to the
Slot number where the module resides. However,
System wide uniqueness is the only true requirement."
::= {cwGlobalChanDataEntry 1 }
cwChanGlobalTransactionId OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This reflects the transaction Identifier of the last
successful connection configuration on the slot
(represented by cwSlotIndex).
The value of this object is incremented every time a
connection(ATM/Frame Relay) is successfully added,
deleted, modified or administratively up/down.
The transaction identifier of the each provisioned
ATM connection endpoint is represented by cwaChanUploadCounter
in the cwaChanCnfgTable.
The transcation identifer of the each provisioned
Frame Relay connection endpoint is represented by
frChanCnfChangeCount in frChanCnfGrpTable."
REFERENCE
"frChanCnfChangeCount in CISCO-WAN-FR-CONN-MIB.my"
::= {cwGlobalChanDataEntry 2 }
-- conformance information
ciscoWanAtmConnMIBConformance
OBJECT IDENTIFIER ::= { ciscoWanAtmConnMIB 2 }
ciscoWanAtmConnMIBCompliances
OBJECT IDENTIFIER ::= { ciscoWanAtmConnMIBConformance 1 }
ciscoWanAtmConnMIBGroups
OBJECT IDENTIFIER ::= { ciscoWanAtmConnMIBConformance 2 }
-- compliance statements
ciscoWanAtmConnMIBCompliance MODULE-COMPLIANCE
STATUS deprecated -- replaced by ciscoWanAtmConnMIBCompliance2
DESCRIPTION
"The compliance statement for the Cisco ATM connection
management group."
MODULE -- this module
MANDATORY-GROUPS { ciscoWanAtmConnChanMIBGroup }
GROUP ciscoWanAtmConnStateGroup
DESCRIPTION
"Implementation of this group is optional for the
systems where connection state is not available
per connection basis."
OBJECT cwaChanFrameDiscard
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support frame discard feature."
OBJECT cwaChanCCEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Continuity Check capability."
OBJECT cwaChanStatsEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
does not support the connection related statistics
collection."
OBJECT cwaChanAbrERS
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Explicit Rate Stamping(ERS)."
OBJECT cwaChanAbrVSVDEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Virtual Source Virtual Destination
feature."
::= { ciscoWanAtmConnMIBCompliances 1 }
ciscoWanAtmConnMIBCompliance2 MODULE-COMPLIANCE
STATUS deprecated -- replaced by ciscoWanAtmConnMIBCompliance3
DESCRIPTION
"The compliance statement for the Cisco ATM connection
management group."
MODULE -- this module
MANDATORY-GROUPS { ciscoWanAtmConnChan2MIBGroup }
GROUP ciscoWanAtmConnStateGroup
DESCRIPTION
"Implementation of this group is optional for the
systems where connection state is not available
per connection basis."
OBJECT cwaChanFrameDiscard
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support frame discard feature."
OBJECT cwaChanCCEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Continuity Check capability."
OBJECT cwaChanStatsEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
does not support the connection related statistics
collection."
OBJECT cwaChanAbrERS
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Explicit Rate Stamping(ERS)."
OBJECT cwaChanAbrVSVDEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Virtual Source Virtual Destination
feature."
::= { ciscoWanAtmConnMIBCompliances 2 }
ciscoWanAtmConnMIBCompliance3 MODULE-COMPLIANCE
STATUS deprecated -- replaced by ciscoWanAtmConnMIBCompliance4
DESCRIPTION
"The compliance statement for the Cisco ATM connection
management group."
MODULE -- this module
MANDATORY-GROUPS { ciscoWanAtmConnChan3MIBGroup }
GROUP ciscoWanAtmConnStateGroup
DESCRIPTION
"Implementation of this group is optional for the
systems where connection state is not available
per connection basis."
GROUP ciscoWanAtmInformationGroup
DESCRIPTION
"Implementation of this group is mandatory for
systems supporting those traps/notifications
with these objects."
OBJECT cwaChanFrameDiscard
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support frame discard feature."
OBJECT cwaChanCCEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Continuity Check capability."
OBJECT cwaChanStatsEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
does not support the connection related statistics
collection."
OBJECT cwaChanAbrVSVDEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Virtual Source Virtual Destination
feature."
OBJECT cwaChanSlaveType
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support non-persistent SPVC."
OBJECT cwaChanRoutingPriority
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Routing Priority."
::= { ciscoWanAtmConnMIBCompliances 3 }
ciscoWanAtmConnMIBCompliance4 MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the Cisco ATM connection
management group."
MODULE -- this module
MANDATORY-GROUPS { ciscoWanAtmConnChan4MIBGroup }
GROUP ciscoWanAtmConnStateGroup
DESCRIPTION
"Implementation of this group is optional for the
systems where connection state is not available
per connection basis."
GROUP ciscoWanAtmInformationGroup
DESCRIPTION
"Implementation of this group is mandatory for
systems supporting those traps/notifications
with these objects."
OBJECT cwaChanFrameDiscard
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support frame discard feature."
OBJECT cwaChanCCEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Continuity Check capability."
OBJECT cwaChanStatsEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
does not support the connection related statistics
collection."
OBJECT cwaChanAbrVSVDEnable
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Virtual Source Virtual Destination
feature."
OBJECT cwaChanSlaveType
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support non-persistent SPVC."
OBJECT cwaChanRoutingPriority
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support Routing Priority."
OBJECT cwaChanP2MP
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support point-to-multipoint connections."
OBJECT cwaChanPrefRouteId
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support preferred route connections."
OBJECT cwaChanDirectRoute
MIN-ACCESS not-accessible
DESCRIPTION
"Read and write access is not required for the switches
which does not support preferred route connections."
::= { ciscoWanAtmConnMIBCompliances 4 }
-- units of conformance
ciscoWanAtmConnChanMIBGroup OBJECT-GROUP
OBJECTS {
cwaChanServiceCategory,
cwaChanVpcFlag,
cwaChanStatsEnable,
cwaChanCCEnable,
cwaChanUploadCounter,
cwaChanIdentifier,
cwaChanLocalVpi,
cwaChanLocalVci,
cwaChanLocalNSAPAddr,
cwaChanRemoteVpi,
cwaChanRemoteVci,
cwaChanRemoteNSAPAddr,
cwaChanControllerId,
cwaChanRoutingMastership,
cwaChanMaxCost,
cwaChanReroute,
cwaChanFrameDiscard,
cwaChanOperStatus,
cwaChanPCR,
cwaChanMCR,
cwaChanSCR,
cwaChanCDV,
cwaChanCTD,
cwaChanMBS,
cwaChanCDVT,
cwaChanPercentUtil,
cwaChanRemotePCR,
cwaChanRemoteMCR,
cwaChanRemoteSCR,
cwaChanRemoteCDV,
cwaChanRemoteCTD,
cwaChanRemoteMBS,
cwaChanRemoteCDVT,
cwaChanRemotePercentUtil,
cwaChanAbrICR,
cwaChanAbrADTF,
cwaChanAbrRDF,
cwaChanAbrRIF,
cwaChanAbrNRM,
cwaChanAbrTRM,
cwaChanAbrCDF,
cwaChanAbrFRTT,
cwaChanAbrTBE,
cwaChanAbrERS,
cwaChanAbrVSVDEnable,
cwaChanRowStatus,
cwaChanIntAbrVSVD,
cwaChanExtAbrVSVD,
cwaChanAisIWCapability,
cwaChanCLR,
cwaChanRemoteCLR,
cwaChanTestType,
cwaChanTestDir,
cwaChanTestIterations,
cwaChanTestState,
cwaChanTestRoundTripDelay
}
STATUS deprecated -- replaced by ciscoWanAtmConnChan2MIBGroup
DESCRIPTION
"Objects related to connection information."
::= { ciscoWanAtmConnMIBGroups 1 }
ciscoWanAtmConnStateGroup OBJECT-GROUP
OBJECTS {
cwaChanAlarmState,
cwaChanEgressXmtState,
cwaChanEgressRcvState,
cwaChanIngressXmtState,
cwaChanIngressRcvState
}
STATUS current
DESCRIPTION
"Objects related to connection state information."
::= { ciscoWanAtmConnMIBGroups 2 }
ciscoWanAtmConnChan2MIBGroup OBJECT-GROUP -- replaced by ciscoWanAtmConnChan3MIBGroup
OBJECTS {
cwaChanServiceCategory,
cwaChanVpcFlag,
cwaChanStatsEnable,
cwaChanCCEnable,
cwaChanUploadCounter,
cwaChanIdentifier,
cwaChanLocalVpi,
cwaChanLocalVci,
cwaChanLocalNSAPAddr,
cwaChanRemoteVpi,
cwaChanRemoteVci,
cwaChanRemoteNSAPAddr,
cwaChanControllerId,
cwaChanRoutingMastership,
cwaChanMaxCost,
cwaChanReroute,
cwaChanFrameDiscard,
cwaChanOperStatus,
cwaChanPCR,
cwaChanMCR,
cwaChanSCR,
cwaChanCDV,
cwaChanCTD,
cwaChanMBS,
cwaChanCDVT,
cwaChanPercentUtil,
cwaChanRemotePCR,
cwaChanRemoteMCR,
cwaChanRemoteSCR,
cwaChanRemoteCDV,
cwaChanRemoteCTD,
cwaChanRemoteMBS,
cwaChanRemotePercentUtil,
cwaChanAbrICR,
cwaChanAbrADTF,
cwaChanAbrRDF,
cwaChanAbrRIF,
cwaChanAbrNRM,
cwaChanAbrTRM,
cwaChanAbrCDF,
cwaChanAbrFRTT,
cwaChanAbrTBE,
cwaChanAbrERS,
cwaChanAbrVSVDEnable,
cwaChanRowStatus,
cwaChanIntAbrVSVD,
cwaChanExtAbrVSVD,
cwaChanAisIWCapability,
cwaChanCLR,
cwaChanRemoteCLR,
cwaChanOamSegEpEnable,
cwaChanTestType,
cwaChanTestDir,
cwaChanTestIterations,
cwaChanTestState,
cwaChanTestRoundTripDelay
}
STATUS deprecated -- replaced by ciscoWanAtmConnChan3MIBGroup
DESCRIPTION
"Objects related to connection information."
::= { ciscoWanAtmConnMIBGroups 3 }
ciscoWanAtmConnChan3MIBGroup OBJECT-GROUP
OBJECTS {
cwaChanServiceCategory,
cwaChanVpcFlag,
cwaChanStatsEnable,
cwaChanCCEnable,
cwaChanUploadCounter,
cwaChanIdentifier,
cwaChanLocalVpi,
cwaChanLocalVci,
cwaChanLocalNSAPAddr,
cwaChanRemoteVpi,
cwaChanRemoteVci,
cwaChanRemoteNSAPAddr,
cwaChanControllerId,
cwaChanRoutingMastership,
cwaChanMaxCost,
cwaChanReroute,
cwaChanFrameDiscard,
cwaChanOperStatus,
cwaChanPCR,
cwaChanMCR,
cwaChanSCR,
cwaChanCDV,
cwaChanCTD,
cwaChanMBS,
cwaChanCDVT,
cwaChanPercentUtil,
cwaChanRemotePCR,
cwaChanRemoteMCR,
cwaChanRemoteSCR,
cwaChanRemoteCDV,
cwaChanRemoteCTD,
cwaChanRemoteMBS,
cwaChanRemotePercentUtil,
cwaChanAbrICR,
cwaChanAbrADTF,
cwaChanAbrRDF,
cwaChanAbrRIF,
cwaChanAbrNRM,
cwaChanAbrTRM,
cwaChanAbrCDF,
cwaChanAbrFRTT,
cwaChanAbrTBE,
cwaChanAbrVSVDEnable,
cwaChanRowStatus,
cwaChanIntAbrVSVD,
cwaChanExtAbrVSVD,
cwaChanCLR,
cwaChanRemoteCLR,
cwaChanOamSegEpEnable,
cwaChanSlaveType,
cwaChanRoutingPriority,
cwaChanTestType,
cwaChanTestDir,
cwaChanTestIterations,
cwaChanTestState,
cwaChanTestRoundTripDelay
}
STATUS deprecated -- replaced by ciscoWanAtmConnChan4MIBGroup
DESCRIPTION
"Objects related to connection information."
::= { ciscoWanAtmConnMIBGroups 4 }
ciscoWanAtmInformationGroup OBJECT-GROUP
OBJECTS {
cwaChanNumVPCsInAlarm,
cwaChanNumVCCsInAlarm
}
STATUS current
DESCRIPTION
"This group contains objects related to the
number of VPCs and VCCs in alarm."
::= { ciscoWanAtmConnMIBGroups 5 }
ciscoWanAtmConnChan4MIBGroup OBJECT-GROUP
OBJECTS {
cwaChanServiceCategory,
cwaChanVpcFlag,
cwaChanStatsEnable,
cwaChanCCEnable,
cwaChanUploadCounter,
cwaChanIdentifier,
cwaChanLocalVpi,
cwaChanLocalVci,
cwaChanLocalNSAPAddr,
cwaChanRemoteVpi,
cwaChanRemoteVci,
cwaChanRemoteNSAPAddr,
cwaChanControllerId,
cwaChanRoutingMastership,
cwaChanMaxCost,
cwaChanReroute,
cwaChanFrameDiscard,
cwaChanOperStatus,
cwaChanPCR,
cwaChanMCR,
cwaChanSCR,
cwaChanCDV,
cwaChanCTD,
cwaChanMBS,
cwaChanCDVT,
cwaChanPercentUtil,
cwaChanRemotePCR,
cwaChanRemoteMCR,
cwaChanRemoteSCR,
cwaChanRemoteCDV,
cwaChanRemoteCTD,
cwaChanRemoteMBS,
cwaChanRemotePercentUtil,
cwaChanAbrICR,
cwaChanAbrADTF,
cwaChanAbrRDF,
cwaChanAbrRIF,
cwaChanAbrNRM,
cwaChanAbrTRM,
cwaChanAbrCDF,
cwaChanAbrFRTT,
cwaChanAbrTBE,
cwaChanAbrVSVDEnable,
cwaChanRowStatus,
cwaChanIntAbrVSVD,
cwaChanExtAbrVSVD,
cwaChanCLR,
cwaChanRemoteCLR,
cwaChanOamSegEpEnable,
cwaChanSlaveType,
cwaChanRoutingPriority,
cwaChanP2MP,
cwaChanPrefRouteId,
cwaChanDirectRoute,
cwaChanTestType,
cwaChanTestDir,
cwaChanTestIterations,
cwaChanTestState,
cwaChanTestRoundTripDelay
}
STATUS current
DESCRIPTION
"Objects related to connection information."
::= { ciscoWanAtmConnMIBGroups 6 }
ciscoWanConMIBGroup OBJECT-GROUP
OBJECTS {
cwChanGlobalTransactionId
}
STATUS current
DESCRIPTION
"The group containing Objects related to
connection provision changes."
::= { ciscoWanAtmConnMIBGroups 7 }
END
Reference in New Issue View Git Blame Copy Permalink