snmp_mib_archive/CISCO-MGX82XX-CARD-FEATURE-MIB.my

-- *****************************************************************
-- ciscoMgx82xxCardFeatureMIB
--
-- May   2003, Subra Hegde
--
-- Copyright (c) 2003 by cisco Systems, Inc.
-- All rights reserved.
-- ****************************************************************

CISCO-MGX82XX-CARD-FEATURE-MIB DEFINITIONS ::= BEGIN
IMPORTS
    MODULE-IDENTITY,
    OBJECT-TYPE,
    Integer32
                               FROM SNMPv2-SMI
    MODULE-COMPLIANCE,
    OBJECT-GROUP               FROM SNMPv2-CONF
    cardSpecific               FROM BASIS-MIB
    ciscoWan                   FROM CISCOWAN-SMI;

ciscoMgx82xxCardFeatureMIB MODULE-IDENTITY
    LAST-UPDATED    "200305050000Z"
    ORGANIZATION    "Cisco Systems, Inc."
    CONTACT-INFO
            "       Cisco Systems
                        Customer Service

                Postal: 170 W Tasman Drive
                        San Jose, CA  95134
                        USA

                        Tel: +1 800 553-NETS

                E-mail: cs-wanatm@cisco.com"
    DESCRIPTION
        "The MIB module which describes the features
        supported in MGX82XX products.
        This MIB Module provides the features supported
        in Controller Cards in MGX8250 and MGX8220.
  
        Terminologies used:

        PXM : Processor Switch Module. This is controller
              card in MGX8250.
        ASC : AXIS Shelf Controller. This is controller
              card in MGX8220.
        VSI : Virtual Switch Interface, a hardware-independent 
              switch control protocol. This allows a Switch to be
              controlled by a multiple controllers such as PNNI, MPLS.
              These control planes can be internal or external to the
              switch.The VSI interface defines the messages and associated
              functions which allow communication between the controller
              and the switch.This interface is expected to support all
              types of connections (voice,data,frame relay,ATM) for PVCs,
              SPVCs and SVCs.
 
         Controller - Software ( and possibly hardware) which manages
                      topology and network resources and performs VSI 
                      Master function. This performs source routing 
                      for end-to-end SVCs, including general call 
                      acceptance GCAC,setup calls with other controllers.
                      PNNI and MPLS are examples of controllers."

    REVISION    "200305050000Z"
    DESCRIPTION
        "Initial version of the MIB.

        The content of this MIB was originally available
        in CISCO-WAN-AXIPOP-MIB defined using SMIv1.
        The applicable objects from CISCO-WAN-AXIPOP-MIB
        are defined using SMIv2 in this MIB. Also the
        descriptions of some of the objects have been 
        modified."
    ::= { ciscoWan 74 }

ascFeatures      OBJECT IDENTIFIER ::= { cardSpecific 5 }
pxmFeatures      OBJECT IDENTIFIER ::= { cardSpecific 15 }
coreCardCommands OBJECT IDENTIFIER ::= { cardSpecific 20 }

vsiControllersAllowed OBJECT-TYPE
    SYNTAX      Integer32 (0..16777215)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This respesents bit map of the VSI Controllers
        supported. 
        The bit positions are :

        BIT  0 - PAR(Portable AutoRoute Controller)
        BIT  1 - PNNI(Private network to network Interface)
        BIT  2 - TAG(Tag Switching or MPLS Controller)
        (e.g. A value of 1 in BIT 0 indicates the presence of PAR )
        Remaining bits are set to 0."
    ::= { pxmFeatures 1 }

apsCardAttributes OBJECT-TYPE
    SYNTAX     Integer32 (0..255)
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "This respesents bit map of the APS card attributes
        supported. 
        The bit position supported are:
          BITs 0, 1     - unused
          BIT  2        - APS standard protocol configured
                         (1 = TRUE ; 0 = FALSE)
          BIT  3, 4 ,5  - unused
          BIT  6        - Card HW supports APS 1+1 on two cards
                          (1 = TRUE ; 0 = FALSE)
          BIT  7        - Card FW supports APS 
                          (1 = TRUE ; 0 = FALSE)
          Remaining bits are set to 0."
    ::= { pxmFeatures 2 }

trkCACEnable  OBJECT-TYPE
    SYNTAX  INTEGER {
                disable (1),
                enable  (2)
            }
    MAX-ACCESS read-write
    STATUS     current
    DESCRIPTION
        "This MIB variable allows to add a new connection on 
        the feeder trunk even if it is over-subscribed."
    DEFVAL { disable }
    ::= { pxmFeatures 3 }	

pxmCardCacMode  OBJECT-TYPE
    SYNTAX  INTEGER {
                pcrBasedCac (1),
                scrBasedCac (2)
            }
    MAX-ACCESS read-write
    STATUS     current
    DESCRIPTION
        "This object identifies the CAC mode set on a card.

        If this is set to pcrBasedCAC(1) then the CAC calculations
        will be done based on PCR on the connection. 

        If this set to scrBasedCAC(2) then the CAC calculations 
        are done based on the scr of the connections. 
        This will be applicable only if CAC is enabled
        (i.e trkCACEnable is set to enable(2))."
    DEFVAL { pcrBasedCac }
    ::= { pxmFeatures 4 }	

redundancyAllowed OBJECT-TYPE
    SYNTAX  INTEGER {
                redNotAllowed (1),
                redAllowed    (2)
            }
    MAX-ACCESS read-only
    STATUS     current
    DESCRIPTION
        "This object identifies whether redundancy 
        is allowed in  MGX82XX shelf."
    ::= { ascFeatures 1 }

switchCoreCard OBJECT-TYPE
    SYNTAX  INTEGER {
		noAction         (1),
		doswitchcc       (2),
		instswitchcc     (3),
		fallbackswitchcc (4)
	}
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This object is  used for performing switchover of
        core card set. The core card set includes Controller Card
        and Service Redundancy Module(SRM).

        The possible values are :
         noAction        (1): No operation
         doswitchcc      (2): Perform switchover operation
         instswitchcc    (3): Perform switchover operation
         fallbackswitchcc(4): "
    ::= { coreCardCommands 1 }

-- conformance information

cmCardFeatureMIBConformance  OBJECT IDENTIFIER ::=
                             { ciscoMgx82xxCardFeatureMIB 2 }

cmCardFeatureMIBGroups       OBJECT IDENTIFIER ::= 
                              { cmCardFeatureMIBConformance 1 }

cmCardFeatureMIBCompliances  OBJECT IDENTIFIER ::= 
                              { cmCardFeatureMIBConformance 2 }

-- compliance statements

cmCardFeatureCompliance MODULE-COMPLIANCE
    STATUS  current 
    DESCRIPTION
        "The compliance statement for objects related
        to Frame Relay Ports."
    MODULE  -- this module
        MANDATORY-GROUPS {
            cmPxmCardFeatureGroup,
            cmAscCardFeatureGroup,
            cmCoreCardFeatureGroup
        }
    ::= { cmCardFeatureMIBCompliances 1 }

cmPxmCardFeatureGroup OBJECT-GROUP
    OBJECTS {
        vsiControllersAllowed,
        apsCardAttributes,
        trkCACEnable,
        pxmCardCacMode    
      }
      STATUS current
      DESCRIPTION
          "The collection of objects which are used to represent
          Processor Module(PXM) Features."
      ::= { cmCardFeatureMIBGroups 1 }
  
cmAscCardFeatureGroup OBJECT-GROUP
    OBJECTS {
        redundancyAllowed
      }
      STATUS current
      DESCRIPTION
          "The collection of objects which are used to represent
          Axis Shelf Controller(ASC) Features."
      ::= { cmCardFeatureMIBGroups 2 }

cmCoreCardFeatureGroup OBJECT-GROUP
    OBJECTS {
        switchCoreCard
    }
    STATUS current
     DESCRIPTION
         "The collection of objects which are used to represent
         core card related objects."
      ::= { cmCardFeatureMIBGroups 3 }

END