MrMeeb/snmp_mib_archive
1
0
Fork 0
mirror of https://github.com/hsnodgrass/snmp_mib_archive.git synced 2025-04-17 16:03:04 +00:00
Code Issues Actions Packages Projects Releases Wiki Activity
snmp_mib_archive/CISCO-IETF-VDSL-LINE-MIB.my 2
Heston Snodgrass 89bf4b016e initial commit
2016-12-15 15:03:18 -07:00

1377 lines
52 KiB
Plaintext
Raw Blame History

-- CISCO-IETF-VDSL-LINE-MIB.my : Description of managed objects for VDSL
-- line interfaces.
--
-- February 2002, Kalyan R. Dharanipragada
--
-- Copyright (c) 1999-2002 by cisco Systems, Inc.
-- All rights reserved.
-- This MIB module is based on the Internet Draft
-- draft-ietf-adslmib-vdsl-00.txt. In terms of object syntax and
-- semantics, the content of this Cisco MIB is the same as
-- the corresponding Internet Draft revision except for the fact that
-- several tables in the internet draft which were based on the draft
-- High capacity MIB textual conventions have been left out.
-- This Cisco MIB was created due to the "subject to change" nature
-- of Internet Drafts. This Cisco MIB may later be deprecated, and
-- the stable RFC, which may replace the Internet Draft, may be
-- implemented in its place.
CISCO-IETF-VDSL-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Gauge32,
Integer32,
NOTIFICATION-TYPE FROM SNMPv2-SMI
TEXTUAL-CONVENTION,
RowStatus,
TruthValue FROM SNMPv2-TC
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF
ifIndex FROM IF-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB
ciscoExperiment FROM CISCO-SMI;
ciscoIetfVdslMIB MODULE-IDENTITY
LAST-UPDATED "200204180000Z" -- April 18, 2002
ORGANIZATION "Cisco Systems"
CONTACT-INFO "Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
Tel: +1 800 553-NETS
E-mail: cs-2900lre@cisco.com"
DESCRIPTION
"The MIB module defining objects for the management of a pair of
VDSL modems at each end of the VDSL line. Each VDSL line has
an entry in an ifTable.
An agent may reside at either end of the VDSL line however the
MIB is designed to require no management communication between
them beyond that inherent in the low-level VDSL line protocol.
The agent may monitor and control this protocol for its needs.
VDSL lines may support optional Fast or Interleaved channels.
If these are supported, additional entries corresponding to the
supported channels must be created in the ifTable. Thus a VDSL
line that supports both channels will have three entries in the
ifTable, one for each physical, fast, and interleaved, whose
ifType values are equal to vdsl(97), fast(125), and
interleaved(124), respectively. The ifStackTable is used to
represent the relationship between the entries.
Naming Conventions:
Vtuc -- (VTUC) modem at near (Central) end of line
Vtur -- (VTUR) modem at Remote end of line
Vtu -- One of either Vtuc or Vtur
Curr -- Current
Prev -- Previous
Atn -- Attenuation
ES -- Errored Second.
LCS -- Line Code Specific
Lof -- Loss of Frame
Lol -- Loss of Link
Los -- Loss of Signal
Lpr -- Loss of Power
xyzs -- interval of Seconds in which xyz occurs
(e.g., xyz=Lof, Los, Lpr)
Max -- Maximum
Mgn -- Margin
Min -- Minimum
Psd -- Power Spectral Density
Snr -- Signal to Noise Ratio
Tx -- Transmit
Blks -- Blocks, a data unit, see cvdslVtuXChanCrcBlockLength
"
REVISION "200204180000Z" -- April 18, 2002
DESCRIPTION "This is a cisco version of the Internet draft"
::= { ciscoExperiment 87 }
cvdslLineMib OBJECT IDENTIFIER ::= { ciscoIetfVdslMIB 1 }
cvdslMibObjects OBJECT IDENTIFIER ::= { cvdslLineMib 1 }
--
-- textual conventions used in this MIB
--
CVdslLineCodingType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This data type is used as the syntax for the VDSL
Line Code."
SYNTAX INTEGER
{
other(1), -- none of the following
mcm(2), -- Multiple Carrier Modulation
scm(3) -- Single Carrier Modulation
}
CVdslLineEntity ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"Identifies a modem as being either Vtuc or Vtur. A
VDSL line consists of two modems, a Vtuc and a Vtur."
SYNTAX INTEGER
{
vtuc(1), -- central site modem
vtur(2) -- remote site modem
}
--
-- objects
--
cvdslLineTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslLineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table includes common attributes describing
both ends of the line. It is required for all VDSL
physical interfaces. VDSL physical interfaces are
those ifEntries where ifType is equal to vdsl(97)."
::= { cvdslMibObjects 1 }
cvdslLineEntry OBJECT-TYPE
SYNTAX CvdslLineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the cvdslLineTable."
INDEX { ifIndex }
::= { cvdslLineTable 1 }
CvdslLineEntry ::=
SEQUENCE
{
cvdslLineCoding CVdslLineCodingType,
cvdslLineType INTEGER,
cvdslLineConfProfile Integer32,
cvdslLineAlarmConfProfile Integer32
}
cvdslLineCoding OBJECT-TYPE
SYNTAX CVdslLineCodingType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the VDSL coding type used on this line."
::= { cvdslLineEntry 1 }
cvdslLineType OBJECT-TYPE
SYNTAX INTEGER
{
noChannel(1), -- no channels exist
fastOnly(2), -- fast channel only
slowOnly(3), -- slow channel only
either(4), -- either fast or slow channel exist
both(5) -- both fast and slow channels exist
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Defines the type of VDSL physical line
entity that exists, by defining whether and how
the line is channelized. If the line is channelized,
the value will be other than noChannel(1). This
object defines which channel type(s) are supported.
In the case that the line is channelized, the manager
can use the ifStackTable to determine the ifIndex for
the associated channel(s)."
::= { cvdslLineEntry 2 }
cvdslLineConfProfile OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the rows
in the VDSL Line Configuration Profile Table,
( cvdslLineConfProfileTable ), which apply for this
VDSL line, and channels if applicable."
::= { cvdslLineEntry 3 }
cvdslLineAlarmConfProfile OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the rows in the VDSL
Line Alarm Configuration Profile Table,
( cvdslLineAlarmConfProfileTable ), which apply to this
VDSL line, and channels if applicable."
::= { cvdslLineEntry 4 }
cvdslPhysTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslPhysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu. Each row
contains the Physical Layer Parameters table for that
Vtu. VDSL physical interfaces are those ifEntries where
ifType is equal to vdsl(97)."
::= { cvdslMibObjects 2 }
cvdslPhysEntry OBJECT-TYPE
SYNTAX CvdslPhysEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION "An entry in the cvdslPhysTable."
INDEX { ifIndex, cvdslPhysSide }
::= { cvdslPhysTable 1 }
CvdslPhysEntry ::=
SEQUENCE
{
cvdslPhysSide CVdslLineEntity,
cvdslInvSerialNumber SnmpAdminString,
cvdslInvVendorID SnmpAdminString,
cvdslInvVersionNumber SnmpAdminString,
cvdslCurrSnrMgn INTEGER,
cvdslCurrAtn Gauge32,
cvdslCurrStatus BITS,
cvdslCurrOutputPwr INTEGER,
cvdslCurrAttainableRate Gauge32
}
cvdslPhysSide OBJECT-TYPE
SYNTAX CVdslLineEntity
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Identifies whether the modem is the Vtuc or Vtur."
::= { cvdslPhysEntry 1 }
cvdslInvSerialNumber OBJECT-TYPE
SYNTAX SnmpAdminString(SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific string that identifies the
vendor equipment."
::= { cvdslPhysEntry 2 }
cvdslInvVendorID OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor ID code is a copy of the binary vendor
identification field defined by the PHY[10] and
expressed as readable characters."
::= { cvdslPhysEntry 3 }
cvdslInvVersionNumber OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The vendor specific version number sent by this Vtu
as part of the initialization messages. It is a copy
of the binary version number field defined by the
PHY[10] and expressed as readable characters."
::= { cvdslPhysEntry 4 }
cvdslCurrSnrMgn OBJECT-TYPE
SYNTAX INTEGER(-640..640)
UNITS "tenth dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Noise Margin as seen by this Vtu with respect to its
received signal in tenth dB."
::= { cvdslPhysEntry 5 }
cvdslCurrAtn OBJECT-TYPE
SYNTAX Gauge32(0..630)
UNITS "tenth dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Measured difference in the total power transmitted by
the peer Vtu and the total power received by this Vtu."
::= { cvdslPhysEntry 6 }
cvdslCurrStatus OBJECT-TYPE
SYNTAX BITS
{
noDefect(0),
lossOfFraming(1),
lossOfSignal(2),
lossOfPower(3),
lossOfSignalQuality(4),
lossOfLink(5),
dataInitFailure(6),
configInitFailure(7),
protocolInitFailure(8),
noPeerVtuPresent(9)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state of the Vtu line. This is a
bit-map of possible conditions. The various bit
positions are:
0 noDefect There no defects on the line
1 lossOfFraming Vtu failure due to not receiving
valid frame.
2 lossOfSignal Vtu failure due to not receiving
signal.
3 lossOfPower Vtu failure due to loss of power.
4 lossOfSignalQuality Loss of Signal Quality is declared
when the Noise Margin falls below
the Minimum Noise Margin, or the
bit-error-rate exceeds 10^-7.
5 lossOfLink Vtu failure due to inability to
link with peer Vtu.
6 dataInitFailure Vtu failure during initialization
due to bit errors corrupting
startup exchange data.
7 configInitFailure Vtu failure during initialization
due to peer Vtu not able to support
requested configuration.
8 protocolInitFailure Vtu failure during initialization
due to incompatible protocol used
by the peer Vtu.
9 noPeerVtuPresent Vtu failure during initialization
due to no activation sequence
detected from peer Vtu.
This is intended to supplement ifOperStatus."
::= { cvdslPhysEntry 7 }
cvdslCurrOutputPwr OBJECT-TYPE
SYNTAX INTEGER (-310..310)
UNITS "tenth dBm"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Measured total output power transmitted by this ATU.
This is the measurement that was reported during
the last activation sequence."
::= { cvdslPhysEntry 8 }
cvdslCurrAttainableRate OBJECT-TYPE
SYNTAX Gauge32
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the maximum currently attainable data rate
by the Vtu. This value will be equal or greater than
the current line rate."
::= { cvdslPhysEntry 9 }
cvdslChanTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslChanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each Vtu channel.
VDSL channel interfaces are those ifEntries where
ifType is equal to interleave(124) or fast(125)."
::= { cvdslMibObjects 3 }
cvdslChanEntry OBJECT-TYPE
SYNTAX CvdslChanEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the cvdslChanTable."
INDEX { ifIndex, cvdslPhysSide }
::= { cvdslChanTable 1 }
CvdslChanEntry ::=
SEQUENCE
{
cvdslChanInterleaveDelay Gauge32,
cvdslChanCrcBlockLength Gauge32
}
cvdslChanInterleaveDelay OBJECT-TYPE
SYNTAX Gauge32
UNITS "milli-seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Interleave Delay for this channel.
Interleave delay applies only to the interleave
(slow) channel and defines the mapping (relative
spacing) between subsequent input bytes at the
interleaver input and their placement in the bit
stream at the interleaver output. Larger numbers
provide greater separation between consecutive
input bytes in the output bit stream allowing for
improved impulse noise immunity at the expense of
payload latency.
In the case where the ifType is fast(125), the
object is not instantiated."
::= { cvdslChanEntry 1 }
cvdslChanCrcBlockLength OBJECT-TYPE
SYNTAX Gauge32
UNITS "byte"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the length of the channel data-block
on which the CRC operates."
::= { cvdslChanEntry 2 }
-- ::= { cvdslMibObjects 4 } not used, cvdslPerfDataTable removed
-- ::= { cvdslMibObjects 5 } not used, cvdslPerfIntervalTable removed
-- ::= { cvdslMibObjects 6 } not used, cvdslChanPerfDataTable removed
-- ::= { cvdslMibObjects 7 } not used, cvdslChanIntervalTable removed
cvdslLineConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslLineConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information on the VDSL line
configuration. One entry in this table reflects a
profile defined by a manager which can be used to
configure the VDSL line."
::= { cvdslMibObjects 8 }
cvdslLineConfProfileEntry OBJECT-TYPE
SYNTAX CvdslLineConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry consists of a list of parameters that
represents the configuration of a VDSL modem. A
default profile with an index of 1 will always exist
and its parameters will be set to vendor specific
values, unless otherwise specified in this document."
INDEX { cvdslPhysSide, cvdslLineConfProfileIndex }
::= { cvdslLineConfProfileTable 1 }
CvdslLineConfProfileEntry ::=
SEQUENCE
{
cvdslLineConfProfileIndex Integer32,
cvdslLineConfProfileName SnmpAdminString,
cvdslLineConfTargetSnrMgn INTEGER,
cvdslLineConfTxSpeed INTEGER,
cvdslLineConfRxSpeed INTEGER,
cvdslLineConfProfileRowStatus RowStatus
}
cvdslLineConfProfileIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used by the line configuration table
in order to identify a row in that table. The system
will always provide a default profile whose value is 1."
::= { cvdslLineConfProfileEntry 1 }
cvdslLineConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The name for this profile as specified by a user."
::= { cvdslLineConfProfileEntry 2 }
cvdslLineConfTargetSnrMgn OBJECT-TYPE
SYNTAX INTEGER (0..310)
UNITS "tenth dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Configured Target Signal/Noise Margin. This is the
Noise Margin the modem must achieve with a BER of 10-7
or better to successfully complete initialization."
::= { cvdslLineConfProfileEntry 3 }
cvdslLineConfTxSpeed OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
UNITS "bits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Transmit speed for this modem. The corresponding modem
on the other end of the VDSL line will have an equal
cvdslLineConfRxSpeed value."
::= { cvdslLineConfProfileEntry 4 }
cvdslLineConfRxSpeed OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
UNITS "bits per second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Receive speed for this modem. The corresponding modem
on the other end of the VDSL line will have an equal
cvdslLineConfTxSpeed value."
::= { cvdslLineConfProfileEntry 5 }
cvdslLineConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines.
The DEFVAL profile cannot be deleted."
::= { cvdslLineConfProfileEntry 6 }
--
-- Multiple carrier modulation (MCM) configuration profile tables
--
cvdslLineMCMConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslLineMCMConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information on the VDSL line
configuration. One entry in this table reflects a
profile defined by a manager which can be used to
configure the VDSL line."
::= { cvdslMibObjects 9 }
cvdslLineMCMConfProfileEntry OBJECT-TYPE
SYNTAX CvdslLineMCMConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry consists of a list of parameters that
represents the configuration of a multiple carrier
modulation VDSL modem. A default profile with an
index of 1 will always exist and its parameters will
be set to vendor specific values, unless otherwise
specified in this document."
INDEX { cvdslPhysSide, cvdslLineConfProfileIndex }
::= { cvdslLineMCMConfProfileTable 1 }
CvdslLineMCMConfProfileEntry ::=
SEQUENCE
{
cvdslMCMConfProfileTxWindowLength INTEGER,
cvdslMCMConfProfileRowStatus RowStatus
}
cvdslMCMConfProfileTxWindowLength OBJECT-TYPE
SYNTAX INTEGER(1..255)
UNITS "samples"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the length of the transmit window, counted
in samples at the sampling rate corresponding to the
negotiated value of N."
::= { cvdslLineMCMConfProfileEntry 1 }
cvdslMCMConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines."
::= { cvdslLineMCMConfProfileEntry 2 }
cvdslLineMCMConfProfileTxBandTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslLineMCMConfProfileTxBandEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains transmit band descriptor configuration
information for a VDSL line. Each entry in this table
reflects the configuration for one of possibly many bands
with a multiple carrier modulation (MCM) VDSL line.
These entries are defined by a manager and can be used to
configure the VDSL line."
::= { cvdslMibObjects 10 }
cvdslLineMCMConfProfileTxBandEntry OBJECT-TYPE
SYNTAX CvdslLineMCMConfProfileTxBandEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry consists of a transmit band descriptor, which
is defined by a start and a stop tone index.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document."
INDEX { cvdslPhysSide, cvdslLineConfProfileIndex,
cvdslMCMConfProfileTxBandNumber }
::= { cvdslLineMCMConfProfileTxBandTable 1 }
CvdslLineMCMConfProfileTxBandEntry ::=
SEQUENCE
{
cvdslMCMConfProfileTxBandNumber INTEGER,
cvdslMCMConfProfileTxBandStart INTEGER,
cvdslMCMConfProfileTxBandStop INTEGER,
cvdslMCMConfProfileTxBandRowStatus RowStatus
}
cvdslMCMConfProfileTxBandNumber OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index for this band descriptor entry."
::= { cvdslLineMCMConfProfileTxBandEntry 1 }
cvdslMCMConfProfileTxBandStart OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Start tone index for this band."
::= { cvdslLineMCMConfProfileTxBandEntry 2 }
cvdslMCMConfProfileTxBandStop OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Stop tone index for this band."
::= { cvdslLineMCMConfProfileTxBandEntry 3 }
cvdslMCMConfProfileTxBandRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines."
::= { cvdslLineMCMConfProfileTxBandEntry 4 }
cvdslLineMCMConfProfileRxBandTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslLineMCMConfProfileRxBandEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains receive band descriptor configuration
information for a VDSL line. Each entry in this table
reflects the configuration for one of possibly many bands
with a multiple carrier modulation (MCM) VDSL line.
These entries are defined by a manager and can be used to
configure the VDSL line."
::= { cvdslMibObjects 11 }
cvdslLineMCMConfProfileRxBandEntry OBJECT-TYPE
SYNTAX CvdslLineMCMConfProfileRxBandEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry consists of a transmit band descriptor, which
defines the start and stop bands and the power spectral
density (PSD) for that band.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document."
INDEX { cvdslPhysSide, cvdslLineConfProfileIndex,
cvdslMCMConfProfileRxBandNumber }
::= { cvdslLineMCMConfProfileRxBandTable 1 }
CvdslLineMCMConfProfileRxBandEntry ::=
SEQUENCE
{
cvdslMCMConfProfileRxBandNumber INTEGER,
cvdslMCMConfProfileRxBandStart INTEGER,
cvdslMCMConfProfileRxBandStop INTEGER,
cvdslMCMConfProfileRxBandRowStatus RowStatus
}
cvdslMCMConfProfileRxBandNumber OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index for this band descriptor entry."
::= { cvdslLineMCMConfProfileRxBandEntry 1 }
cvdslMCMConfProfileRxBandStart OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Start tone index for this band."
::= { cvdslLineMCMConfProfileRxBandEntry 2 }
cvdslMCMConfProfileRxBandStop OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Stop tone index for this band."
::= { cvdslLineMCMConfProfileRxBandEntry 3 }
cvdslMCMConfProfileRxBandRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines."
::= { cvdslLineMCMConfProfileRxBandEntry 4 }
cvdslLineMCMConfProfileTxPSDTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslLineMCMConfProfileTxPSDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains transmit PSD mask descriptor
configuration information for a VDSL line. Each entry in
this table reflects the configuration for one tone within
a multiple carrier modulation (MCM) VDSL line. These
entries are defined by a manager and can be used to
configure the VDSL line."
::= { cvdslMibObjects 12 }
cvdslLineMCMConfProfileTxPSDEntry OBJECT-TYPE
SYNTAX CvdslLineMCMConfProfileTxPSDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry consists of a transmit PSD mask descriptor,
which defines the power spectral density (PSD) for a tone.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document."
INDEX { cvdslPhysSide, cvdslLineConfProfileIndex,
cvdslMCMConfProfileTxPSDNumber }
::= { cvdslLineMCMConfProfileTxPSDTable 1 }
CvdslLineMCMConfProfileTxPSDEntry ::=
SEQUENCE
{
cvdslMCMConfProfileTxPSDNumber INTEGER,
cvdslMCMConfProfileTxPSDTone INTEGER,
cvdslMCMConfProfileTxPSDPSD INTEGER,
cvdslMCMConfProfileTxPSDRowStatus RowStatus
}
cvdslMCMConfProfileTxPSDNumber OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index for this mask descriptor entry."
::= { cvdslLineMCMConfProfileTxPSDEntry 1 }
cvdslMCMConfProfileTxPSDTone OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The tone index for which the PSD is being specified."
::= { cvdslLineMCMConfProfileTxPSDEntry 2 }
cvdslMCMConfProfileTxPSDPSD OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
UNITS "0.5dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Power Spectral Density level in steps of 0.5dB with
an offset of -140dbm/Hz."
::= { cvdslLineMCMConfProfileTxPSDEntry 3 }
cvdslMCMConfProfileTxPSDRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines."
::= { cvdslLineMCMConfProfileTxPSDEntry 4 }
cvdslLineMCMConfProfileMaxTxPSDTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslLineMCMConfProfileMaxTxPSDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains transmit maximum PSD mask descriptor
configuration information for a VDSL line. Each entry in
this table reflects the configuration for one tone within
a multiple carrier modulation (MCM) VDSL modem. These
entries are defined by a manager and can be used to
configure the VDSL line."
::= { cvdslMibObjects 13 }
cvdslLineMCMConfProfileMaxTxPSDEntry OBJECT-TYPE
SYNTAX CvdslLineMCMConfProfileMaxTxPSDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry consists of a transmit PSD mask descriptor,
which defines the maximum power spectral density (PSD)
for a tone.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document."
INDEX { cvdslPhysSide, cvdslLineConfProfileIndex,
cvdslMCMConfProfileMaxTxPSDNumber }
::= { cvdslLineMCMConfProfileMaxTxPSDTable 1 }
CvdslLineMCMConfProfileMaxTxPSDEntry ::=
SEQUENCE
{
cvdslMCMConfProfileMaxTxPSDNumber INTEGER,
cvdslMCMConfProfileMaxTxPSDTone INTEGER,
cvdslMCMConfProfileMaxTxPSDPSD INTEGER,
cvdslMCMConfProfileMaxTxPSDRowStatus RowStatus
}
cvdslMCMConfProfileMaxTxPSDNumber OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index for this band descriptor entry."
::= { cvdslLineMCMConfProfileMaxTxPSDEntry 1 }
cvdslMCMConfProfileMaxTxPSDTone OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The tone index for which the PSD is being specified."
::= { cvdslLineMCMConfProfileMaxTxPSDEntry 2 }
cvdslMCMConfProfileMaxTxPSDPSD OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
UNITS "0.5dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Power Spectral Density level in steps of 0.5dB with
an offset of -140dbm/Hz."
::= { cvdslLineMCMConfProfileMaxTxPSDEntry 3 }
cvdslMCMConfProfileMaxTxPSDRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines."
::= { cvdslLineMCMConfProfileMaxTxPSDEntry 4 }
cvdslLineMCMConfProfileMaxRxPSDTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslLineMCMConfProfileMaxRxPSDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains maximum receive PSD mask descriptor
configuration information for a VDSL line. Each entry in
this table reflects the configuration for one tone within
a multiple carrier modulation (MCM) VDSL modem. These
entries are defined by a manager and can be used to
configure the VDSL line."
::= { cvdslMibObjects 14 }
cvdslLineMCMConfProfileMaxRxPSDEntry OBJECT-TYPE
SYNTAX CvdslLineMCMConfProfileMaxRxPSDEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry consists of a transmit PSD mask descriptor,
which defines the power spectral density (PSD) for a
tone.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document."
INDEX { cvdslPhysSide, cvdslLineConfProfileIndex,
cvdslMCMConfProfileMaxRxPSDNumber }
::= { cvdslLineMCMConfProfileMaxRxPSDTable 1 }
CvdslLineMCMConfProfileMaxRxPSDEntry ::=
SEQUENCE
{
cvdslMCMConfProfileMaxRxPSDNumber INTEGER,
cvdslMCMConfProfileMaxRxPSDTone INTEGER,
cvdslMCMConfProfileMaxRxPSDPSD INTEGER,
cvdslMCMConfProfileMaxRxPSDRowStatus RowStatus
}
cvdslMCMConfProfileMaxRxPSDNumber OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index for this band descriptor entry."
::= { cvdslLineMCMConfProfileMaxRxPSDEntry 1 }
cvdslMCMConfProfileMaxRxPSDTone OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The tone index for which the PSD is being specified."
::= { cvdslLineMCMConfProfileMaxRxPSDEntry 2 }
cvdslMCMConfProfileMaxRxPSDPSD OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
UNITS "0.5dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Power Spectral Density level in steps of 0.5dB with
an offset of -140dbm/Hz."
::= { cvdslLineMCMConfProfileMaxRxPSDEntry 3 }
cvdslMCMConfProfileMaxRxPSDRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines."
::= { cvdslLineMCMConfProfileMaxRxPSDEntry 4 }
--
-- Single carrier modulation (SCM) configuration profile table
--
cvdslLineSCMConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslLineSCMConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information on the VDSL line
configuration. One entry in this table reflects a
profile defined by a manager which can be used to
configure the VDSL line."
::= { cvdslMibObjects 15 }
cvdslLineSCMConfProfileEntry OBJECT-TYPE
SYNTAX CvdslLineSCMConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry consists of a list of parameters that
represents the configuration of a single carrier
modulation VDSL modem.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document."
INDEX { cvdslPhysSide, cvdslLineConfProfileIndex }
::= { cvdslLineSCMConfProfileTable 1 }
CvdslLineSCMConfProfileEntry ::=
SEQUENCE
{
cvdslSCMConfProfileInterleaveDepth INTEGER,
cvdslSCMConfProfileFastCodewordSize INTEGER,
cvdslSCMConfProfileTransmitPSDMask BITS,
cvdslSCMConfProfileTransmitPSDLevel INTEGER,
cvdslSCMConfProfileSymbolRateProfile INTEGER,
cvdslSCMConfProfileConstellationSize INTEGER,
cvdslSCMConfProfileCenterFrequency INTEGER,
cvdslSCMConfProfileRowStatus RowStatus
}
cvdslSCMConfProfileInterleaveDepth OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
UNITS "octets"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the interleaving depth."
::= { cvdslLineSCMConfProfileEntry 1 }
cvdslSCMConfProfileFastCodewordSize OBJECT-TYPE
SYNTAX INTEGER(0..180)
UNITS "octets"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the length in octets of the fast codeword.
A value of 0 indicates that the single latency transport
class is to be utilized."
::= { cvdslLineSCMConfProfileEntry 2 }
cvdslSCMConfProfileTransmitPSDMask OBJECT-TYPE
SYNTAX BITS
{
vendorNotch1(0), -- vendor specific notch
vendorNotch2(1), -- vendor specific notch
amateurBand30m(2), -- amateur radio 30m band notch
amateurBand40m(3), -- amateur radio 40m band notch
amateurBand80m(4), -- amateur radio 80m band notch
amateurBand160m(5) -- amateur radio 160m band notch
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The transmit power spectral density mask code."
::= { cvdslLineSCMConfProfileEntry 3 }
cvdslSCMConfProfileTransmitPSDLevel OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
UNITS "dBm/Hz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The transmit power spectral density for the VDSL modem."
::= { cvdslLineSCMConfProfileEntry 4 }
cvdslSCMConfProfileSymbolRateProfile OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
UNITS "kbaud"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The symbol rate profile calculated as S = SR/BSR, where
SR is the required symbol rate in kbaud, BSR = 67.5."
::= { cvdslLineSCMConfProfileEntry 5 }
cvdslSCMConfProfileConstellationSize OBJECT-TYPE
SYNTAX INTEGER(0..15)
UNITS "log2"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the constellation size."
::= { cvdslLineSCMConfProfileEntry 6 }
cvdslSCMConfProfileCenterFrequency OBJECT-TYPE
SYNTAX INTEGER(0..511)
UNITS "kHz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Specifies the center frequency profile K."
::= { cvdslLineSCMConfProfileEntry 7 }
cvdslSCMConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines."
::= { cvdslLineSCMConfProfileEntry 8 }
--
-- Alarm configuration profile table
--
cvdslLineAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF CvdslLineAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information on the VDSL line alarm
configuration. One entry in this table reflects a profile
defined by a manager which can be used to configure the
VDSL line alarm thresholds."
::= { cvdslMibObjects 16 }
cvdslLineAlarmConfProfileEntry OBJECT-TYPE
SYNTAX CvdslLineAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry consists of a list of parameters that
represents the configuration of a VDSL line alarm
profile.
A default profile with an index of 1 will always exist and
its parameters will be set to vendor specific values,
unless otherwise specified in this document."
INDEX { cvdslPhysSide, cvdslLineAlarmConfProfileIndex }
::= { cvdslLineAlarmConfProfileTable 1 }
CvdslLineAlarmConfProfileEntry ::=
SEQUENCE
{
cvdslLineAlarmConfProfileIndex Integer32,
cvdslLineAlarmConfProfileName SnmpAdminString,
cvdslInitFailureNotificationEnable TruthValue,
cvdslLineAlarmConfProfileRowStatus RowStatus
}
cvdslLineAlarmConfProfileIndex OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used by the line alarm configuration table
in order to identify a row in that table. The system will
always provide a default profile whose index is 1."
::= { cvdslLineAlarmConfProfileEntry 1 }
cvdslLineAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The name for this profile as specified by a user."
::= { cvdslLineAlarmConfProfileEntry 2 }
cvdslInitFailureNotificationEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies if a cvdslInitFailureNotification
notification will be generated if an initialization
failure occurs."
::= { cvdslLineAlarmConfProfileEntry 3 }
cvdslLineAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or modify or
delete an existing row in this table.
A profile activated by setting this object to `active'.
When `active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of
service, (by setting this object to `destroy' or
`outOfService') it must be first unreferenced
from all associated lines."
::= { cvdslLineAlarmConfProfileEntry 4 }
-- Notification definitions
cvdslNotifications OBJECT IDENTIFIER ::= { cvdslLineMib 0 }
cvdslInitFailureNotification NOTIFICATION-TYPE
OBJECTS {
cvdslCurrStatus
}
STATUS current
DESCRIPTION
"Vtu initialization failed. See cvdslCurrStatus for
potential reasons."
::= { cvdslNotifications 1 }
-- conformance information
cvdslConformance OBJECT IDENTIFIER ::= { cvdslLineMib 3 }
cvdslGroups OBJECT IDENTIFIER ::= { cvdslConformance 1 }
cvdslCompliances OBJECT IDENTIFIER ::= { cvdslConformance 2 }
cvdslLineMibCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities which
manage VDSL interfaces."
MODULE -- this module
MANDATORY-GROUPS
{
cvdslGroup
}
GROUP cvdslMCMGroup
DESCRIPTION
"This group is mandatory for VDSL Lines which
utilize multiple carrier modulation.
This group should not be implemented for VDSL lines
which utilize single carrier modulation."
GROUP cvdslSCMGroup
DESCRIPTION
"This group is mandatory for VDSL lines which
utilize single carrier modulation.
This group should not be implemented for VDSL lines
which utilize multiple carrier modulation"
::= { cvdslCompliances 1 }
-- units of conformance
cvdslGroup OBJECT-GROUP
OBJECTS
{
cvdslLineCoding,
cvdslLineType,
cvdslLineConfProfile,
cvdslLineAlarmConfProfile,
cvdslInvSerialNumber,
cvdslInvVendorID,
cvdslInvVersionNumber,
cvdslCurrSnrMgn,
cvdslCurrAtn,
cvdslCurrStatus,
cvdslCurrOutputPwr,
cvdslCurrAttainableRate,
cvdslChanInterleaveDelay,
cvdslChanCrcBlockLength,
cvdslLineConfProfileName,
cvdslLineConfTargetSnrMgn,
cvdslLineConfTxSpeed,
cvdslLineConfRxSpeed,
cvdslLineConfProfileRowStatus,
cvdslLineAlarmConfProfileName,
cvdslInitFailureNotificationEnable,
cvdslLineAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing information about
a VDSL Line."
::= { cvdslGroups 1 }
cvdslMCMGroup OBJECT-GROUP
OBJECTS
{
cvdslMCMConfProfileTxWindowLength,
cvdslMCMConfProfileRowStatus,
cvdslMCMConfProfileTxBandStart,
cvdslMCMConfProfileTxBandStop,
cvdslMCMConfProfileTxBandRowStatus,
cvdslMCMConfProfileRxBandStart,
cvdslMCMConfProfileRxBandStop,
cvdslMCMConfProfileRxBandRowStatus,
cvdslMCMConfProfileTxPSDTone,
cvdslMCMConfProfileTxPSDPSD,
cvdslMCMConfProfileTxPSDRowStatus,
cvdslMCMConfProfileMaxTxPSDTone,
cvdslMCMConfProfileMaxTxPSDPSD,
cvdslMCMConfProfileMaxTxPSDRowStatus,
cvdslMCMConfProfileMaxRxPSDTone,
cvdslMCMConfProfileMaxRxPSDPSD,
cvdslMCMConfProfileMaxRxPSDRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing configuration
information for a VDSL line based upon multiple carrier
modulation modem."
::= { cvdslGroups 2 }
cvdslSCMGroup OBJECT-GROUP
OBJECTS
{
cvdslSCMConfProfileInterleaveDepth,
cvdslSCMConfProfileFastCodewordSize,
cvdslSCMConfProfileTransmitPSDMask,
cvdslSCMConfProfileTransmitPSDLevel,
cvdslSCMConfProfileSymbolRateProfile,
cvdslSCMConfProfileConstellationSize,
cvdslSCMConfProfileCenterFrequency,
cvdslSCMConfProfileRowStatus
}
STATUS current
DESCRIPTION
"A collection of objects providing configuration
information for a VDSL line based upon single carrier
modulation modem."
::= { cvdslGroups 3 }
cvdslNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS
{
cvdslInitFailureNotification
}
STATUS current
DESCRIPTION
"This group supports notifications of significant
conditions associated with VDSL Lines."
::= { cvdslGroups 4 }
END
Reference in New Issue View Git Blame Copy Permalink