MrMeeb/snmp_mib_archive
1
0
Fork 0
mirror of https://github.com/hsnodgrass/snmp_mib_archive.git synced 2025-04-17 16:03:04 +00:00
Code Issues Actions Packages Projects Releases Wiki Activity
snmp_mib_archive/ADSL2-LINE-MIB.my
Heston Snodgrass 89bf4b016e initial commit
2016-12-15 15:03:18 -07:00

5476 lines
214 KiB
Plaintext
Raw Blame History

ADSL2-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
transmission,
Unsigned32,
NOTIFICATION-TYPE,
Integer32,
Counter32
FROM SNMPv2-SMI
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP
FROM SNMPv2-CONF
ifIndex
FROM IF-MIB
TruthValue,
RowStatus
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
HCPerfIntervalThreshold,
HCPerfTimeElapsed
FROM HC-PerfHist-TC-MIB
Adsl2Unit,
Adsl2Direction,
Adsl2TransmissionModeType,
Adsl2RaMode,
Adsl2InitResult,
Adsl2OperationModes,
Adsl2PowerMngState,
Adsl2ConfPmsForce,
Adsl2LConfProfPmMode,
Adsl2LineLdsf,
Adsl2LdsfResult,
Adsl2SymbolProtection,
Adsl2MaxBer,
Adsl2ScMaskDs,
Adsl2ScMaskUs,
Adsl2RfiDs,
Adsl2PsdMaskDs,
Adsl2PsdMaskUs,
Adsl2Tssi,
Adsl2LastTransmittedState,
Adsl2LineStatus,
Adsl2ChAtmStatus,
Adsl2ChPtmStatus
FROM ADSL2-LINE-TC-MIB;
adsl2MIB MODULE-IDENTITY
LAST-UPDATED "200610040000Z"
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO
"WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed
Sand Channel Systems
Postal: P.O. Box 37324
Raleigh NC 27627-732
Email: sneedmike@hotmail.com
Phone: +1 206 600 7022
Co-Chair & Co-editor:
Menachem Dodge
ECI Telecom Ltd.
Postal: 30 Hasivim St.
Petach Tikva 49517,
Israel.
Email: mbdodge@ieee.org
Phone: +972 3 926 8421
Co-editor: Moti Morgenstern
ECI Telecom Ltd.
Postal: 30 Hasivim St.
Petach Tikva 49517,
Israel.
Email: moti.morgenstern@ecitele.com
Phone: +972 3 926 6258
Co-editor: Scott Baillie
NEC Australia
Postal: 649-655 Springvale Road,
Mulgrave, Victoria 3170,
Australia.
Email: scott.baillie@nec.com.au
Phone: +61 3 9264 3986
Co-editor: Umberto Bonollo
NEC Australia
Postal: 649-655 Springvale Road,
Mulgrave, Victoria 3170,
Australia.
Email: umberto.bonollo@nec.com.au
Phone: +61 3 9264 3385"
DESCRIPTION
"This document defines a Management Information Base (MIB)
module for use with network management protocols in the
Internet community for the purpose of managing ADSL, ADSL2,
and ADSL2+ lines. The MIB module described in RFC 2662
[RFC2662] describes objects used for managing Asymmetric
Bit-Rate DSL (ADSL) interfaces per [T1E1.413], [G.992.1],
and [G.992.2]. These object descriptions are based upon the
specifications for the ADSL Embedded Operations Channel
(EOC) as defined in American National Standards Institute
(ANSI) T1E1.413/1995 [T1E1.413] and International
Telecommunication Union (ITU-T) G.992.1 [G.992.1] and
G.992.2 [G.992.2].
This document does not obsolete RFC 2662 [RFC2662], but
rather provides a more comprehensive management model that
includes the ADSL2 and ADSL2+ technologies per G.992.3,
G.992.4, and G.992.5 ([G.992.3], [G.992.4], and [G.992.5],
respectively). In addition, objects have been added to
improve the management of ADSL, ADSL2, and ADSL2+ lines.
Additionally, the management framework for New Generation
ADSL lines specified by the Digital Subscriber Line Forum
(DSLF) has been taken into consideration [TR-90]. That
framework is based on ITU-T G.997.1 standard [G.997.1] as
well as two amendments: [G.997.1am1] and [G.997.1am2].
Note that the revised ITU-T G.997.1 standard also refers to
the next generation of VDSL technology, known as VDSL2, per
ITU-T G.993.2 [G.993.2]. However, managing VDSL2 lines is
currently beyond the scope of this document.
The MIB module is located in the MIB tree under MIB 2
transmission, as discussed in the IANA Considerations section
of this document.
Copyright (C) The Internet Society (2006). This version of
this MIB module is part of RFC 4706: see the RFC itself for
full legal notices."
REVISION "200610040000Z"
DESCRIPTION
"Initial version, published as RFC 4706."
::= { transmission 238 }
adsl2 OBJECT IDENTIFIER
::= { adsl2MIB 1 }
-- ----------------------------------------------
adsl2Line OBJECT IDENTIFIER
::= { adsl2 1 }
adsl2Status OBJECT IDENTIFIER
::= { adsl2 2 }
adsl2Inventory OBJECT IDENTIFIER
::= { adsl2 3 }
adsl2PM OBJECT IDENTIFIER
::= { adsl2 4 }
adsl2Profile OBJECT IDENTIFIER
::= { adsl2 5 }
adsl2Scalar OBJECT IDENTIFIER
::= { adsl2 6 }
adsl2Notifications OBJECT IDENTIFIER
::= { adsl2 0 }
adsl2Conformance OBJECT IDENTIFIER
::= { adsl2 7 }
-- ----------------------------------------------
adsl2PMLine OBJECT IDENTIFIER
::= { adsl2PM 1 }
adsl2PMChannel OBJECT IDENTIFIER
::= { adsl2PM 2 }
-- ----------------------------------------------
adsl2ProfileLine OBJECT IDENTIFIER
::= { adsl2Profile 1 }
adsl2ProfileChannel OBJECT IDENTIFIER
::= { adsl2Profile 2 }
adsl2ProfileAlarmConf OBJECT IDENTIFIER
::= { adsl2Profile 3 }
-- ----------------------------------------------
adsl2ScalarSC OBJECT IDENTIFIER
::= { adsl2Scalar 1 }
-- ----------------------------------------------
--
-- ----------------------------------------------
-- adsl2LineTable --
-- ----------------------------------------------
adsl2LineTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineTable contains configuration,
command, and status parameters of the ADSL2 line.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238).
Several objects in this table MUST be maintained in a
persistent manner."
::= { adsl2Line 1 }
adsl2LineEntry OBJECT-TYPE
SYNTAX Adsl2LineEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineTable contains configuration,
commands, and status parameters of the ADSL2 line"
INDEX { ifIndex }
::= { adsl2LineTable 1 }
Adsl2LineEntry ::= SEQUENCE {
adsl2LineCnfgTemplate SnmpAdminString,
adsl2LineAlarmCnfgTemplate SnmpAdminString,
adsl2LineCmndConfPmsf Adsl2ConfPmsForce,
adsl2LineCmndConfLdsf Adsl2LineLdsf,
adsl2LineCmndConfLdsfFailReason Adsl2LdsfResult,
adsl2LineCmndAutomodeColdStart TruthValue,
adsl2LineStatusAtuTransSys Adsl2TransmissionModeType,
adsl2LineStatusPwrMngState Adsl2PowerMngState,
adsl2LineStatusInitResult Adsl2InitResult,
adsl2LineStatusLastStateDs Adsl2LastTransmittedState,
adsl2LineStatusLastStateUs Adsl2LastTransmittedState,
adsl2LineStatusAtur Adsl2LineStatus,
adsl2LineStatusAtuc Adsl2LineStatus,
adsl2LineStatusLnAttenDs Unsigned32,
adsl2LineStatusLnAttenUs Unsigned32,
adsl2LineStatusSigAttenDs Unsigned32,
adsl2LineStatusSigAttenUs Unsigned32,
adsl2LineStatusSnrMarginDs Integer32,
adsl2LineStatusSnrMarginUs Integer32,
adsl2LineStatusAttainableRateDs Unsigned32,
adsl2LineStatusAttainableRateUs Unsigned32,
adsl2LineStatusActPsdDs Integer32,
adsl2LineStatusActPsdUs Integer32,
adsl2LineStatusActAtpDs Integer32,
adsl2LineStatusActAtpUs Integer32
}
adsl2LineCnfgTemplate OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Line
Configuration Templates Table, (adsl2LineConfTemplateTable),
which applies for this ADSL2 line.
This object MUST be maintained in a persistent manner."
REFERENCE "DSL Forum TR-90, paragraph 5.1.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineEntry 1 }
adsl2LineAlarmCnfgTemplate OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Line
Alarm Configuration Template Table,
(adsl2LineAlarmConfTemplateTable), which applies to this ADSL2
line.
This object MUST be maintained in a persistent manner."
REFERENCE "DSL Forum TR-90, paragraph 5.1.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineEntry 2 }
adsl2LineCmndConfPmsf OBJECT-TYPE
SYNTAX Adsl2ConfPmsForce
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Power management state forced. Defines the line states to be
forced by the near-end ATU on this line. The various possible
values are:
l3toL0(0),
l0toL2(2), or
l0orL2toL3(3).
This object MUST be maintained in a persistent manner."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.3"
DEFVAL { l3toL0 }
::= { adsl2LineEntry 3 }
adsl2LineCmndConfLdsf OBJECT-TYPE
SYNTAX Adsl2LineLdsf
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Loop diagnostics mode forced (LDSF). Defines whether the line
should be forced into the loop diagnostics mode by the
near-end ATU on this line or only be responsive to loop
diagnostics initiated by the far-end ATU.
This object MUST be maintained in a persistent manner.
However, in case the operator forces loop diagnostics mode
then the access node should reset the object (inhibit) when
loop diagnostics mode procedures are completed."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.8"
DEFVAL { inhibit }
::= { adsl2LineEntry 4 }
adsl2LineCmndConfLdsfFailReason OBJECT-TYPE
SYNTAX Adsl2LdsfResult
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The status of the recent occasion the Loop diagnostics mode
forced (LDSF) was issued for the associated line. Possible
values are:
none(1) - The default value in case LDSF was never
requested for the associated line.
success(2) - The recent command completed
successfully.
inProgress(3) - The Loop Diagnostics process is in
progress.
unsupported(4) - The NE or the line card doesn't support
LDSF.
cannotRun(5) - The NE cannot initiate the command, due
to a nonspecific reason.
aborted(6) - The Loop Diagnostics process aborted.
failed(7) - The Loop Diagnostics process failed.
illegalMode(8) - The NE cannot initiate the command, due
to the specific mode of the relevant
line.
adminUp(9) - The NE cannot initiate the command, as
the relevant line is administratively
'Up'.
tableFull(10) - The NE cannot initiate the command, due
to reaching the maximum number of rows
in the results table.
noResources(11) - The NE cannot initiate the command, due
to lack of internal memory resources."
DEFVAL { none }
::= { adsl2LineEntry 5 }
adsl2LineCmndAutomodeColdStart OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Automode cold start forced. This parameter is defined
in order to improve testing of the performance of ATUs
supporting automode when it is enabled in the MIB.
Change the value of this parameter to 'true' indicates
a change in loop conditions applied to the devices under
test. The ATUs shall reset any historical information
used for automode and for shortening G.994.1 handshake
and initialization.
Automode is the case where multiple operation-modes are
enabled through the adsl2LConfProfAtuTransSysEna object
in the line configuration profile being used for the
ADSL line, and where the selection of the actual
operation-mode depends not only on the common
capabilities of both ATUs (as exchanged in G.994.1), but
also on achievable data rates under given loop
conditions.
This object MUST be maintained in a persistent manner."
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.10"
DEFVAL { false }
::= { adsl2LineEntry 6 }
adsl2LineStatusAtuTransSys OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU Transmission System (ATS) in use.
It is coded in a bit-map representation with only a single bit
set to '1' (the selected coding for the ADSL line). This
parameter may be derived from the handshaking procedures
defined in Recommendation G.994.1. A set of ADSL2 line
transmission modes, with one bit per mode."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.1"
::= { adsl2LineEntry 7 }
adsl2LineStatusPwrMngState OBJECT-TYPE
SYNTAX Adsl2PowerMngState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current power management state. One of four possible
power management states:
L0 - Synchronized and full transmission (i.e., Showtime).
L1 - Low Power with reduced net data rate (G.992.2 only).
L2 - Low Power with reduced net data rate (G.992.3 and
G.992.4 only).
L3 - No power.
The various possible values are: l0(1), l1(2), l2(3), or
l3(4)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.2"
::= { adsl2LineEntry 8 }
adsl2LineStatusInitResult OBJECT-TYPE
SYNTAX Adsl2InitResult
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the result of the last full initialization performed
on the line. It is an enumeration type with the following
values: noFail(0), configError(1), configNotFeasible(2),
commFail(3), noPeerAtu(4), or otherCause(5)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.3"
::= { adsl2LineEntry 9 }
adsl2LineStatusLastStateDs OBJECT-TYPE
SYNTAX Adsl2LastTransmittedState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last successful transmitted initialization state in
the downstream direction in the last full initialization
performed on the line."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.4"
::= { adsl2LineEntry 10 }
adsl2LineStatusLastStateUs OBJECT-TYPE
SYNTAX Adsl2LastTransmittedState
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The last successful transmitted initialization state in the
upstream direction in the last full initialization performed
on the line."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.5"
::= { adsl2LineEntry 11 }
adsl2LineStatusAtur OBJECT-TYPE
SYNTAX Adsl2LineStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state (existing failures) of the ATU-R.
This is a bit-map of possible conditions."
REFERENCE "ITU-T G.997.1, paragraph 7.1.1.2"
::= { adsl2LineEntry 12 }
adsl2LineStatusAtuc OBJECT-TYPE
SYNTAX Adsl2LineStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates current state (existing failures) of the ATU-C.
This is a bit-map of possible conditions."
REFERENCE "ITU-T G.997.1, paragraph 7.1.1.1"
::= { adsl2LineEntry 13 }
adsl2LineStatusLnAttenDs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub-
carriers during diagnostics mode and initialization. It
ranges from 0 to 1270 units of 0.1 dB (physical values
are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the line
attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the line
attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.6"
::= { adsl2LineEntry 14 }
adsl2LineStatusLnAttenUs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub-
carriers during diagnostics mode and initialization.
It ranges from 0 to 1270 units of 0.1 dB (physical values are
0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the line
attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the line
attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.7"
::= { adsl2LineEntry 15 }
adsl2LineStatusSigAttenDs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub-
carriers during Showtime. It ranges from 0 to 1270 units of
0.1 dB (physical values are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.8"
::= { adsl2LineEntry 16 }
adsl2LineStatusSigAttenUs OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The measured difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub-
carriers during Showtime. It ranges from 0 to 1270 units of
0.1 dB (physical values are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.9"
::= { adsl2LineEntry 17 }
adsl2LineStatusSnrMarginDs OBJECT-TYPE
SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Downstream SNR Margin is the maximum increase in dB of the
noise power received at the ATU-R, such that the BER
requirements are met for all downstream bearer channels. It
ranges from -640 to 630 units of 0.1 dB (physical values are
-64 to 63 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
SNR Margin is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
SNR Margin measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.10"
::= { adsl2LineEntry 18 }
adsl2LineStatusSnrMarginUs OBJECT-TYPE
SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Upstream SNR Margin is the maximum increase in dB of the noise
power received at the ATU-C, such that the BER requirements
are met for all downstream bearer channels. It ranges from
-640 to 630 units of 0.1 dB (physical values are -64 to
63 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
SNR Margin is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
SNR Margin measurement is currently unavailable."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.11"
::= { adsl2LineEntry 19 }
adsl2LineStatusAttainableRateDs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate Downstream.
The maximum downstream net data rate currently attainable by
the ATU-C transmitter and the ATU-R receiver, coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.12"
::= { adsl2LineEntry 20 }
adsl2LineStatusAttainableRateUs OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate Upstream.
The maximum upstream net data rate currently attainable by the
ATU-R transmitter and the ATU-C receiver, coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.13"
::= { adsl2LineEntry 21 }
adsl2LineStatusActPsdDs OBJECT-TYPE
SYNTAX Integer32 (-900..0 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Power Spectrum Density (PSD) Downstream. The average
downstream transmit PSD over the sub-carriers used for
downstream. It ranges from -900 to 0 units of 0.1 dB
(physical values are -90 to 0 dBm/Hz).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.14"
::= { adsl2LineEntry 22 }
adsl2LineStatusActPsdUs OBJECT-TYPE
SYNTAX Integer32 (-900..0 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Power Spectrum Density (PSD) Upstream. The average
upstream transmit PSD over the sub-carriers used for upstream.
It ranges from -900 to 0 units of 0.1 dB (physical values
are -90 to 0 dBm/Hz).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.15"
::= { adsl2LineEntry 23 }
adsl2LineStatusActAtpDs OBJECT-TYPE
SYNTAX Integer32 (-310..310 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Aggregate Transmit Power Downstream. The total amount
of transmit power delivered by the ATU-C at the U-C reference
point, at the instant of measurement. It ranges from -310 to
310 units of 0.1 dB (physical values are -31 to 31 dBm).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.16"
::= { adsl2LineEntry 24 }
adsl2LineStatusActAtpUs OBJECT-TYPE
SYNTAX Integer32 (-310..310 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Aggregate Transmit Power Upstream. The total amount of
transmit power delivered by the ATU-R at the U-R
reference point, at the instant of measurement. It ranges
from -310 to 310 units of 0.1 dB (physical values are -31
to 31 dBm).
A value of 0x7FFFFFFF (2147483647) indicates the measurement
is out of range to be represented."
REFERENCE "ITU-T G.997.1, paragraph 7.5.1.17"
::= { adsl2LineEntry 25 }
-- ----------------------------------------------
-- adsl2ChannelStatusTable --
-- ----------------------------------------------
adsl2ChannelStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChannelStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChannelStatusTable contains status
parameters of the ADSL2 channel. This table contains live
data from equipment."
::= { adsl2Status 1 }
adsl2ChannelStatusEntry OBJECT-TYPE
SYNTAX Adsl2ChannelStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChannelStatusTable contains status
parameters of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL channel, along with a termination unit."
INDEX {
ifIndex,
adsl2ChStatusUnit
}
::= { adsl2ChannelStatusTable 1 }
Adsl2ChannelStatusEntry ::= SEQUENCE {
adsl2ChStatusUnit Adsl2Unit,
adsl2ChStatusChannelNum Unsigned32,
adsl2ChStatusActDataRate Unsigned32,
adsl2ChStatusPrevDataRate Unsigned32,
adsl2ChStatusActDelay Unsigned32,
adsl2ChStatusAtmStatus Adsl2ChAtmStatus,
adsl2ChStatusPtmStatus Adsl2ChPtmStatus
}
adsl2ChStatusUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit atuc(1) or atur(2)."
::= { adsl2ChannelStatusEntry 1 }
adsl2ChStatusChannelNum OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Provides the bearer channel number associated with this
row (i.e., the channel ifIndex).
This enables determining the channel configuration profile
and the channel thresholds profile applicable for this
bearer channel."
::= { adsl2ChannelStatusEntry 2 }
adsl2ChStatusActDataRate OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual net data rate that the bearer channel is operating
at, if in L0 power management state. In L1 or L2 states, it
relates to the previous L0 state. The data rate is coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.1"
::= { adsl2ChannelStatusEntry 3 }
adsl2ChStatusPrevDataRate OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The previous net data rate that the bearer channel was
operating at just before the latest rate change event. This
could be a full or short initialization, fast retrain, DRA or
power management transitions, excluding transitions between L0
state and L1 or L2 states. The data rate is coded in
bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.2"
::= { adsl2ChannelStatusEntry 4 }
adsl2ChStatusActDelay OBJECT-TYPE
SYNTAX Unsigned32 (0..8176 )
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The actual one-way interleaving delay introduced by the
PMS-TC in the direction of the bearer channel, if in L0
power management state. In L1 or L2 states, it relates to
the previous L0 state. It is coded in ms (rounded to the
nearest ms)."
REFERENCE "ITU-T G.997.1, paragraph 7.5.2.3"
::= { adsl2ChannelStatusEntry 5 }
adsl2ChStatusAtmStatus OBJECT-TYPE
SYNTAX Adsl2ChAtmStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current state (existing failures) of the ADSL
channel in case its Data Path is ATM. This is a bit-map of
possible conditions. The various bit positions are:
noDefect(0),
noCellDelineation(1), or
lossOfCellDelineation(2).
In the case where the channel is not an ATM Data Path, the
object is set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.1.4"
::= { adsl2ChannelStatusEntry 6 }
adsl2ChStatusPtmStatus OBJECT-TYPE
SYNTAX Adsl2ChPtmStatus
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current state (existing failures) of the ADSL
channel in case its Data Path is PTM. This is a bit-map of
possible conditions. The various bit positions are:
noDefect(0), or
outOfSync(1).
In the case where the channel is not a PTM Data Path, the
object is set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.1.5"
::= { adsl2ChannelStatusEntry 7 }
-- ----------------------------------------------
-- Scalars that relate to the adsl2SCStatusTable.
-- ----------------------------------------------
adsl2ScalarSCMaxInterfaces OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value determines the upper size of adsl2SCStatusTable.
The maximum number of entries in adsl2SCStatusTable is equal
to two times the value of this attribute."
::= { adsl2ScalarSC 1 }
adsl2ScalarSCAvailInterfaces OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value determines the amount of space that is
currently available in adsl2SCStatusTable.
The number of entries available in adsl2SCStatusTable is equal
to two times the value of this attribute."
::= { adsl2ScalarSC 2 }
-- ----------------------------------------------
-- adsl2SCStatusTable --
-- ----------------------------------------------
adsl2SCStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2SCStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2SCStatusTable contains status parameters
of the ADSL2 sub-carriers. The following points apply to this
table:
1. The main purpose of this table is to hold the results
of a DELT.
2. This table also holds parameters obtained at line
initialization time.
3. The rows in this table are volatile; that is, they are
lost if the SNMP agent is rebooted.
4. Due to the large OCTET STRING attributes in this table,
the worst case memory requirements for this table are
very high. The manager may use the row status attribute
of this table to delete rows in order to reclaim memory.
5. The manager may create rows in this table. The SNMP
agent may create rows in this table. Only the manager
may delete rows in this table.
6. The maximum number of rows allowable in this table is
indicated by the scalar attribute
adsl2ScalarSCMaxInterfaces.
The number of rows available in this table is indicated
by the scalar attribute adsl2ScalarSCAvailInterfaces.
7. The SNMP agent is permitted to create rows in this table
when a DELT completes successfully or when line
initialization occurs. It is not mandatory for the SNMP
agent to create rows in this table; hence, it may be
necessary for the manager to create rows in this table
before any results can be stored.
8. If the manager attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail, and the response to the SNMP SET PDU
will contain the error noCreation(11).
9. If the SNMP agent attempts to create a row in this table
and there are no more rows available, the creation
attempt will fail, and the attribute
adsl2LineCmndConfLdsfFailReason will indicate the
reason for the failure. The failure reason will be either
tableFull(10) or noResources(11).
10. An example of use of this table is as follows:
Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT completes, and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : Due to a low memory condition, a row in the
: adsl2SCStatusTable table cannot be created at
: this time.
Step 5. : The reason for the failure, tableFull(10), is
: indicated in the adsl2LineCmndConfLdsfFailReason
: attribute.
11. Another example of use of this table is as follows :
Step 1. : The DELT is started by setting the
: adsl2LineCmndConfLdsf from inhibit to force.
Step 2. : The DELT completes and valid data is
: available.
Step 3. : The row in the adsl2SCStatusTable where the
: results will be stored does not yet exist so
: the SNMP agent attempts to create the row.
Step 4. : The row creation is successful.
Step 5. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2).
12. Another example of use of this table is as follows:
Step 1. : The manager creates a row in adsl2SCStatusTable
: for a particular ADSL2 line.
Step 2. : The DELT is started on the above-mentioned
: line by setting the adsl2LineCmndConfLdsf from
: inhibit to force.
Step 3. : The DELT completes, and valid data is
: available.
Step 4. : The value of the attribute
: adsl2LineCmndConfLdsfFailReasonreason is set
: to success(2)."
::= { adsl2Status 2 }
adsl2SCStatusEntry OBJECT-TYPE
SYNTAX Adsl2SCStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table Adsl2SCStatusEntry contains status parameters
of the ADSL2 sub-carriers.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238)."
INDEX {
ifIndex,
adsl2SCStatusDirection
}
::= { adsl2SCStatusTable 1 }
Adsl2SCStatusEntry ::= SEQUENCE {
adsl2SCStatusDirection Adsl2Direction,
adsl2SCStatusMtime Unsigned32,
adsl2SCStatusSnr OCTET STRING,
adsl2SCStatusBitsAlloc OCTET STRING,
adsl2SCStatusGainAlloc OCTET STRING,
adsl2SCStatusTssi Adsl2Tssi,
adsl2SCStatusLinScale Unsigned32,
adsl2SCStatusLinReal OCTET STRING,
adsl2SCStatusLinImg OCTET STRING,
adsl2SCStatusLogMt Unsigned32,
adsl2SCStatusLog OCTET STRING,
adsl2SCStatusQlnMt Unsigned32,
adsl2SCStatusQln OCTET STRING,
adsl2SCStatusLnAtten Unsigned32,
adsl2SCStatusSigAtten Unsigned32,
adsl2SCStatusSnrMargin Integer32,
adsl2SCStatusAttainableRate Unsigned32,
adsl2SCStatusActAtp Integer32,
adsl2SCStatusRowStatus RowStatus
}
adsl2SCStatusDirection OBJECT-TYPE
SYNTAX Adsl2Direction
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The direction of the sub-carrier is either
upstream or downstream."
::= { adsl2SCStatusEntry 1 }
adsl2SCStatusMtime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "symbols"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"SNR Measurement Time. The number of symbols used to
measure the SNR values on the respective transmission
direction. It should correspond to the value specified in the
recommendation (e.g., the number of symbols in 1 second
time interval for G.992.3). This parameter corresponds to
1 second in loop diagnostic procedure and should be updated
otherwise."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.20.1 (SNRMTds)
and paragraph 7.5.1.20.3 (SNRMTus)"
::= { adsl2SCStatusEntry 2 }
adsl2SCStatusSnr OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..512))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SNR Margin per sub-carrier, expressing the ratio between
the received signal power and received noise power per
subscriber. It is an array of 512 octets, designed for
supporting up to 512 (downstream) sub-carriers.
The number of utilized octets on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Octet i (0 <= i < NSC) is set to a value in the range 0 to
254 to indicate that the respective downstream or upstream sub-
carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB
(i.e., -32 to 95dB).
The special value 255 means that no measurement could be done
for the subcarrier because it is out of the PSD mask passband
or that the noise PSD is out of range to be represented.
Each value in this array is 8 bits wide."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.20.2 (SNRpsds)
and paragraph 7.5.1.20.4 (SNRpsus)"
::= { adsl2SCStatusEntry 3 }
adsl2SCStatusBitsAlloc OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..256))
UNITS "bits"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The bits allocation per sub-carrier. An array of 256 octets
(512 nibbles), designed for supporting up to 512 (downstream)
sub-carriers.
The number of utilized nibbles on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Nibble i (0 <= i < NSC) is set to a value in the range 0
to 15 to indicate that the respective downstream or upstream
sub-carrier i has the same amount of bits allocation."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.21.1 (BITSpsds)
and paragraph 7.5.1.21.2 (BITSpsus)"
::= { adsl2SCStatusEntry 4 }
adsl2SCStatusGainAlloc OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The gain allocation per sub-carrier. An array of 512 16-bits
values, designed for supporting up to 512 (downstream) sub-
carriers.
The number of utilized octets on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate
that the respective downstream or upstream sub-carrier i has the
same amount of gain value.
The gain value is represented as a multiple of 1/512 on a
linear scale. Each value in this array is 16 bits wide and is
stored in big endian format."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.21.3 (GAINSpsds)
and paragraph 7.5.1.21.4 (GAINSpsus)"
::= { adsl2SCStatusEntry 5 }
adsl2SCStatusTssi OBJECT-TYPE
SYNTAX Adsl2Tssi
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transmit spectrum shaping (TSSi) breakpoints expressed
as the set of breakpoints exchanged during G.994.1.
Each breakpoint is a pair of values occupying 3 octets with the
following structure:
First 2 octets - Index of the subcarrier used in the context of
the breakpoint.
Third octet - The shaping parameter at the breakpoint.
Subcarrier index is an unsigned number in the range 1 to either
NSCds (downstream direction) or NSCus (upstream direction).
The shaping parameter value is in the range 0 to 127 (units of
-0.5dB). The special value 127 indicates that the subcarrier
is not transmitted."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.21.5 (TSSpsds)
and paragraph 7.5.1.21.6 (TSSpsus)"
::= { adsl2SCStatusEntry 6 }
adsl2SCStatusLinScale OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The scale factor to be applied to the H(f) linear
representation values for the respective transmission direction.
This parameter is only available after a loop diagnostic
procedure."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.18.1 (HLINSCds)
and paragraph 7.5.1.18.5 (HLINSCus)"
::= { adsl2SCStatusEntry 7 }
adsl2SCStatusLinReal OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of up to 512 complex H(f) linear representation
values in linear scale for the respective transmission
direction. It is designed to support up to 512 (downstream)
sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the real component [referred to here
as a(i)] of Hlin(f = i*Df) value for a particular sub-carrier
index i (0 <= i < NSC).
Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)),
where scale is Adsl2SubcarrierLinScale and a(i) and b(i)
[provided by the Adsl2SubcarrierLinImg object] are in the range
(-2^15+1) to (+2^15-1).
A special value a(i)=b(i)= -2^15 indicates that no measurement
could be done for the subcarrier because it is out of the
passband or that the attenuation is out of range to be
represented. This parameter is only available after a loop
diagnostic procedure.
Each value in this array is 16 bits wide and is stored in big
endian format."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.18.2 (HLINpsds)
and paragraph 7.5.1.18.6 (HLINpsds)"
::= { adsl2SCStatusEntry 8 }
adsl2SCStatusLinImg OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of up to 512 complex H(f) linear representation
values in linear scale for the respective transmission
direction. It is designed to support up to 512 (downstream)
sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the imaginary component [referred
to here as b(i)] of Hlin(f = i*Df) value for a particular sub-
carrier index i (0 <= i < NSC).
Hlin(f) is represented as ((scale/2^15)*((a(i)+j*b(i))/2^15)),
where scale is Adsl2SubcarrierLinScale and a(i) [provided by
the Adsl2SubcarrierLinReal object] and b(i) are in the range
(-2^15+1) to (+2^15-1).
A special value a(i)=b(i)= -2^15 indicates that no measurement
could be done for the subcarrier because it is out of the
passband or that the attenuation is out of range to be
represented. This parameter is only available after a loop
diagnostic procedure.
Each value in this array is 16 bits wide and is stored in big
endian format."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.18.2 (HLINpsds)
and paragraph 7.5.1.18.6 (HLINpsds)"
::= { adsl2SCStatusEntry 9 }
adsl2SCStatusLogMt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of symbols used to measure the H(f) logarithmic
measurement values for the respective transmission direction.
This parameter should correspond to the value specified in the
recommendation (e.g., the number of symbols in 1 second
time interval for G.992.3). This parameter corresponds to 1
second in loop diagnostic procedure and should be updated in
initialization"
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.18.3 (HLOGMTds)
and paragraph 7.5.1.18.7 (HLOGMTus)"
::= { adsl2SCStatusEntry 10 }
adsl2SCStatusLog OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..1024))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of up to 512 real H(f) logarithmic representation
values in dB for the respective transmission direction. It is
designed to support up to 512 (downstream) sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the real Hlog(f = i*Df) value for a
particular sub-carrier index i, (0 <= i < NSC).
The real Hlog(f) value is represented as (6-m(i)/10), with m(i)
in the range 0 to 1022. A special value m=1023 indicates that
no measurement could be done for the subcarrier because it is
out of the passband or that the attenuation is out of range to
be represented. This parameter is applicable in loop
diagnostic procedure and initialization.
Each value in this array is 16 bits wide and is stored
in big endian format."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.18.4 (HLOGpsds)
and paragraph 7.5.1.18.8 (HLOGpsus)"
::= { adsl2SCStatusEntry 11 }
adsl2SCStatusQlnMt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of symbols used to measure the Quiet Line Noise
values on the respective transmission direction. This
parameter should correspond to the value specified in the
recommendation (e.g., the number of symbols in 1 second time
interval for G.992.3). This parameter corresponds to 1 second
in loop diagnostic procedure and should be updated in
initialization"
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.19.1 (QLNMTds)
and paragraph 7.5.1.19.3 (QLNMTus)"
::= { adsl2SCStatusEntry 12 }
adsl2SCStatusQln OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..512))
UNITS "dBm/Hz"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An array of up to 512 real Quiet Line Noise values in dBm/Hz
for the respective transmission direction. It is designed for
up to 512 (downstream) sub-carriers.
The number of utilized values on downstream direction depends
on NSCds, and on upstream direction it depends on NSCus. This
value is referred to here as NSC.
Each array entry represents the QLN(f = i*Df) value for a
particular sub-carrier index i, (0 <= i < NSC).
The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the
range 0 to 254. A special value n(i)=255 indicates that no
measurement could be done for the subcarrier because it is out
of the passband or that the noise PSD is out of range to be
represented.
This parameter is applicable in loop diagnostic procedure and
initialization. Each value in this array is 8 bits wide."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.19.2 (QLNpsds)
and paragraph 7.5.1.19.4 (QLNpsus)"
::= { adsl2SCStatusEntry 13 }
adsl2SCStatusLnAtten OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When referring to the downstream direction, it is the measured
difference in the total power transmitted by the ATU-C and the
total power received by the ATU-R over all sub-carriers during
diagnostics mode.
When referring to the upstream direction, it is the measured
difference in the total power transmitted by the ATU-R and the
total power received by the ATU-C over all sub-carriers during
diagnostics mode.
It ranges from 0 to 1270 units of 0.1 dB (physical values are
0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the line
attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the line
attenuation measurement is unavailable.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.6 (LATNds)
and paragraph 7.5.1.7 (LATNus)"
::= { adsl2SCStatusEntry 14 }
adsl2SCStatusSigAtten OBJECT-TYPE
SYNTAX Unsigned32 (0..1270 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"When referring to the downstream direction, it is the measured
difference in the total power transmitted by the
ATU-C and the total power received by the ATU-R over all sub-
carriers during Showtime after the diagnostics mode.
When referring to the upstream direction, it is the measured
difference in the total power transmitted by the
ATU-R and the total power received by the ATU-C over all sub-
carriers during Showtime after the diagnostics mode.
It ranges from 0 to 1270 units of 0.1 dB (physical values
are 0 to 127 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
signal attenuation is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
signal attenuation measurement is unavailable.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.8 (SATNds)
and paragraph 7.5.1.9 (SATNus)"
::= { adsl2SCStatusEntry 15 }
adsl2SCStatusSnrMargin OBJECT-TYPE
SYNTAX Integer32 (-640..630 | 2147483646 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"SNR Margin is the maximum increase in dB of the noise power
received at the ATU (ATU-R on downstream direction and ATU-C
on upstream direction), such that the BER requirements are met
for all bearer channels received at the ATU. It ranges from
-640 to 630 units of 0.1 dB (physical values are -64 to
63 dB).
A special value of 0x7FFFFFFF (2147483647) indicates the
SNR Margin is out of range to be represented.
A special value of 0x7FFFFFFE (2147483646) indicates the
SNR Margin measurement is currently unavailable.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.10 (SNRMds)
and paragraph 7.5.1.11 (SNRMus)"
::= { adsl2SCStatusEntry 16 }
adsl2SCStatusAttainableRate OBJECT-TYPE
SYNTAX Unsigned32
UNITS "bits/second"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Maximum Attainable Data Rate. The maximum net data rate
currently attainable by the ATU-C transmitter and ATU-R
receiver (when referring to downstream direction) or by the
ATU-R transmitter and ATU-C receiver (when referring to
upstream direction). Value is coded in bits/second.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.12 (ATTNDRds)
and paragraph 7.5.1.13 (ATTNDRus)"
::= { adsl2SCStatusEntry 17 }
adsl2SCStatusActAtp OBJECT-TYPE
SYNTAX Integer32
UNITS "0.1 dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Actual Aggregate Transmit Power from the ATU (ATU-R on
downstream direction and ATU-C on upstream direction), at the
instant of measurement. It ranges from -310 to 310 units of
0.1 dB (physical values are -31 to 31 dBm). A value of all
1's indicates the measurement is out of range to be
represented.
This object reflects the value of the parameter following the
most recent DELT performed on the associated line. Once
the DELT process is over, the parameter no longer changes
until the row is deleted or a new DELT process is initiated."
REFERENCE
"ITU-T G.997.1, paragraph 7.5.1.16 (ACTATPds)
and paragraph 7.5.1.17 (ACTATPus)"
::= { adsl2SCStatusEntry 18 }
adsl2SCStatusRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Row Status. The manager may create and delete rows
of this table. Please see the description of
adsl2SCStatusTable above for more details."
::= { adsl2SCStatusEntry 19 }
-- ----------------------------------------------
-- adsl2LineInventoryTable --
-- ----------------------------------------------
adsl2LineInventoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineInventoryTable contains inventory of the
ADSL2 units."
::= { adsl2Inventory 1 }
adsl2LineInventoryEntry OBJECT-TYPE
SYNTAX Adsl2LineInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineInventoryTable contains inventory of the
ADSL2 units.
The index of this table is an interface index where the
interface has an ifType of adsl2plus(238)."
INDEX {
ifIndex,
adsl2LInvUnit
}
::= { adsl2LineInventoryTable 1 }
Adsl2LineInventoryEntry ::= SEQUENCE {
adsl2LInvUnit Adsl2Unit,
adsl2LInvG994VendorId OCTET STRING,
adsl2LInvSystemVendorId OCTET STRING,
adsl2LInvVersionNumber OCTET STRING,
adsl2LInvSerialNumber OCTET STRING,
adsl2LInvSelfTestResult Unsigned32,
adsl2LInvTransmissionCapabilities Adsl2TransmissionModeType
}
adsl2LInvUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit atuc(1) or atur(2)."
::= { adsl2LineInventoryEntry 1 }
adsl2LInvG994VendorId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR
message. It consists of 8 binary octets, including a country
code followed by a (regionally allocated) provider code, as
defined in Recommendation T.35."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 2 }
adsl2LInvSystemVendorId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU System Vendor ID (identifies the ATU system
integrator) as inserted in the Overhead Messages (both ATUs
for G.992.3 and G.992.4) or in the Embedded Operations
Channel (only ATU-R in G.992.1 and G.992.2). It consists of
8 binary octets, with the same format as used for
Adsl2InvG994VendorId."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 3 }
adsl2LInvVersionNumber OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..16))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU version number (vendor-specific information) as
inserted in the Overhead Messages (both ATUs for G.992.3 and
G.992.4) or in the Embedded Operations Channel (only ATU-R in
G.992.1 and G.992.2). It consists of up to 16 binary octets."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 4 }
adsl2LInvSerialNumber OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU serial number (vendor-specific information) as
inserted in the Overhead Messages (both ATUs for G.992.3 and
G.992.4) or in the Embedded Operations Channel (only ATU-R in
G.992.1 and G.992.2). It is vendor-specific information. It
consists of up to 32 ASCII characters."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 5 }
adsl2LInvSelfTestResult OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU self-test result, coded as a 32-bit value. The
most significant octet of the result is '0' if the self-test
passed, and '1' if the self-test failed. The interpretation
of the other octets is vendor discretionary."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 6 }
adsl2LInvTransmissionCapabilities OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The ATU transmission system capability list of the different
coding types. It is coded in a bit-map representation with 1
or more bits set. A bit set to '1' means that the ATU
supports the respective coding. The value may be derived
from the handshaking procedures defined in G.994.1. A set
of ADSL2 line transmission modes, with one bit per mode."
REFERENCE "ITU-T G.997.1, paragraph 7.4"
::= { adsl2LineInventoryEntry 7 }
-- ----------------------------------------------
-- adsl2LineConfTemplateTable --
-- ----------------------------------------------
adsl2LineConfTemplateTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfTemplateTable contains ADSL2 line
configuration templates.
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileLine 1 }
adsl2LineConfTemplateEntry OBJECT-TYPE
SYNTAX Adsl2LineConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfTemplateTable contains the ADSL2 line
configuration template.
A default template with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2LConfTempTemplateName }
::= { adsl2LineConfTemplateTable 1 }
Adsl2LineConfTemplateEntry ::= SEQUENCE {
adsl2LConfTempTemplateName SnmpAdminString,
adsl2LConfTempLineProfile SnmpAdminString,
adsl2LConfTempChan1ConfProfile SnmpAdminString,
adsl2LConfTempChan1RaRatioDs Unsigned32,
adsl2LConfTempChan1RaRatioUs Unsigned32,
adsl2LConfTempChan2ConfProfile SnmpAdminString,
adsl2LConfTempChan2RaRatioDs Unsigned32,
adsl2LConfTempChan2RaRatioUs Unsigned32,
adsl2LConfTempChan3ConfProfile SnmpAdminString,
adsl2LConfTempChan3RaRatioDs Unsigned32,
adsl2LConfTempChan3RaRatioUs Unsigned32,
adsl2LConfTempChan4ConfProfile SnmpAdminString,
adsl2LConfTempChan4RaRatioDs Unsigned32,
adsl2LConfTempChan4RaRatioUs Unsigned32,
adsl2LConfTempRowStatus RowStatus
}
adsl2LConfTempTemplateName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
REFERENCE "DSL Forum TR-90, paragraph 5.1.4"
::= { adsl2LineConfTemplateEntry 1 }
adsl2LConfTempLineProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Line
Configuration Profile Table, (adsl2LineConfProfTable),
which applies for this ADSL2 line."
REFERENCE "DSL Forum TR-90, paragraph 5.1.4"
DEFVAL { "DEFVAL" }
::= { adsl2LineConfTemplateEntry 2 }
adsl2LConfTempChan1ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table,
(adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #1. The channel profile name specified here must
match the name of an existing row in the
adsl2ChConfProfileTable table."
DEFVAL { "DEFVAL" }
::= { adsl2LineConfTemplateEntry 3 }
adsl2LConfTempChan1RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32 (0..100 )
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #1 when performing rate
adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the 100 -
adsl2LConfTempChan1RaRatioDs is the ratio of excess data
rate to be assigned to all other bearer channels on Downstream
direction. The sum of rate adaptation ratios over all bearers
on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 100 }
::= { adsl2LineConfTemplateEntry 4 }
adsl2LConfTempChan1RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32 (0..100 )
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #1 when performing rate
adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the
100 - adsl2LConfTempChan1RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 100 }
::= { adsl2LineConfTemplateEntry 5 }
adsl2LConfTempChan2ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table
(adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #2. If the channel is unused, then the object is set
to a zero-length string.
This object may be set to a zero-length string only if
adsl2LConfTempChan3ConfProfile contains a zero-length
string."
DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 6 }
adsl2LConfTempChan2RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32 (0..100 )
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #2 when performing rate
adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the
100 - adsl2LConfTempChan2RaRatioDs is the ratio of excess
data rate to be assigned to all other bearer channels on
Downstream direction. The sum of rate adaptation ratios
over all bearers on the same direction shall be equal to
100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 7 }
adsl2LConfTempChan2RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32 (0..100 )
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #2 when performing rate
adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the
100 - adsl2LConfTempChan2RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 8 }
adsl2LConfTempChan3ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table
(adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #3. If the channel is unused, then the object is set
to a zero-length string.
This object may be set to a zero-length string only if
adsl2LConfTempChan4ConfProfile contains a zero-length
string.
This object may be set to a non-zero-length string only if
adsl2LConfTempChan2ConfProfile contains a non-zero-length
string."
DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 9 }
adsl2LConfTempChan3RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32 (0..100 )
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #3 when performing rate
adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the 100 -
adsl2LConfTempChan3RaRatioDs is the ratio of excess data
rate to be assigned to all other bearer channels on Downstream
direction. The sum of rate adaptation ratios over all bearers
on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 10 }
adsl2LConfTempChan3RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32 (0..100 )
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #3 when performing rate
adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the
100 - adsl2LConfTempChan3RaRatioUs is the ratio of excess
data rate to be assigned to all other bearer channels on
Upstream direction. The sum of rate adaptation ratios over
all bearers on the same direction shall be equal to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 11 }
adsl2LConfTempChan4ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Configuration Profile Table
(adsl2ChConfProfileTable) that applies to ADSL2 bearer
channel #4. If the channel is unused, then the object is set
to a zero-length string.
This object may be set to a non-zero-length string only if
adsl2LConfTempChan3ConfProfile contains a non-zero-length
string."
DEFVAL { "" }
::= { adsl2LineConfTemplateEntry 12 }
adsl2LConfTempChan4RaRatioDs OBJECT-TYPE
SYNTAX Unsigned32 (0..100 )
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #4 when performing rate
adaptation on Downstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over all
bearer channels. Also, the 100 -
adsl2LConfTempChan4RaRatioDs is the ratio of
excess data rate to be assigned to all other bearer channels.
The sum of rate adaptation ratios over all bearers on the same
direction shall sum to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 13 }
adsl2LConfTempChan4RaRatioUs OBJECT-TYPE
SYNTAX Unsigned32 (0..100 )
UNITS "percent"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Rate Adaptation Ratio. The ratio (in %) that should be taken
into account for the bearer channel #4 when performing rate
adaptation on Upstream. The ratio refers to the available
data rate in excess of the Minimum Data Rate, summed over
all bearer channels. Also, the 100 -
adsl2LConfTempChan4RaRatioUs is the
ratio of excess data rate to be assigned to all other bearer
channels. The sum of rate adaptation ratios over all bearers
on the same direction shall sum to 100%."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
DEFVAL { 0 }
::= { adsl2LineConfTemplateEntry 14 }
adsl2LConfTempRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or to modify or
delete an existing row in this table.
A template is activated by setting this object to 'active'.
When 'active' is set, the system will validate the template.
Before a template can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
lines."
::= { adsl2LineConfTemplateEntry 15 }
-- ----------------------------------------
-- adsl2LineConfProfTable --
-- ----------------------------------------
adsl2LineConfProfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfProfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfProfTable contains ADSL2 line profile
configuration.
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileLine 2 }
adsl2LineConfProfEntry OBJECT-TYPE
SYNTAX Adsl2LineConfProfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfProfTable contains ADSL2 line profile
configuration.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2LConfProfProfileName }
::= { adsl2LineConfProfTable 1 }
Adsl2LineConfProfEntry ::= SEQUENCE {
adsl2LConfProfProfileName SnmpAdminString,
adsl2LConfProfScMaskDs Adsl2ScMaskDs,
adsl2LConfProfScMaskUs Adsl2ScMaskUs,
adsl2LConfProfRfiBandsDs Adsl2RfiDs,
adsl2LConfProfRaModeDs Adsl2RaMode,
adsl2LConfProfRaModeUs Adsl2RaMode,
adsl2LConfProfRaUsNrmDs Unsigned32,
adsl2LConfProfRaUsNrmUs Unsigned32,
adsl2LConfProfRaUsTimeDs Unsigned32,
adsl2LConfProfRaUsTimeUs Unsigned32,
adsl2LConfProfRaDsNrmsDs Unsigned32,
adsl2LConfProfRaDsNrmsUs Unsigned32,
adsl2LConfProfRaDsTimeDs Unsigned32,
adsl2LConfProfRaDsTimeUs Unsigned32,
adsl2LConfProfTargetSnrmDs Unsigned32,
adsl2LConfProfTargetSnrmUs Unsigned32,
adsl2LConfProfMaxSnrmDs Unsigned32,
adsl2LConfProfMaxSnrmUs Unsigned32,
adsl2LConfProfMinSnrmDs Unsigned32,
adsl2LConfProfMinSnrmUs Unsigned32,
adsl2LConfProfMsgMinUs Unsigned32,
adsl2LConfProfMsgMinDs Unsigned32,
adsl2LConfProfAtuTransSysEna Adsl2TransmissionModeType,
adsl2LConfProfPmMode Adsl2LConfProfPmMode,
adsl2LConfProfL0Time Unsigned32,
adsl2LConfProfL2Time Unsigned32,
adsl2LConfProfL2Atpr Unsigned32,
adsl2LConfProfL2Atprt Unsigned32,
adsl2LConfProfRowStatus RowStatus
}
adsl2LConfProfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2LineConfProfEntry 1 }
adsl2LConfProfScMaskDs OBJECT-TYPE
SYNTAX Adsl2ScMaskDs
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Sub-carriers mask. A bitmap of 512 bits that allows masking
up to 512 downstream sub-carriers, depending on NSCds. If bit
i (0 <= i < NSCds) is set to '1', the respective
downstream sub-carrier i is masked, and if set to '0', the
respective sub-carrier is unmasked. Note that there should
always be unmasked sub-carriers (i.e., the object cannot be
all 1's). Also note that if NSCds < 512, all bits
i (NSCds < i <= 512) should be set to '1'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.6"
::= { adsl2LineConfProfEntry 2 }
adsl2LConfProfScMaskUs OBJECT-TYPE
SYNTAX Adsl2ScMaskUs
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Sub-carriers mask. A bitmap of 64 bits that allows masking
up to 64 downstream sub-carriers, depending on NSCds. If
bit i (0 <= i < NSCus) is set to '1', the respective
upstream sub-carrier i is masked, and if set to '0', the
respective sub-carrier is unmasked. Note that there
should always be unmasked sub-carriers (i.e., the object
cannot be all 1's). Also note that if NSCus <
64, all bits i (NSCus < i <= 64) should be set to '1'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.7"
::= { adsl2LineConfProfEntry 3 }
adsl2LConfProfRfiBandsDs OBJECT-TYPE
SYNTAX Adsl2RfiDs
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The subset of downstream PSD mask breakpoints that shall be
used to notch an RFI band.
The specific interpolation around these points is defined in
G.992.5. It is a bitmap of 512 bits that allows referring to
up to 512 downstream sub-carriers, depending on NSCds. If bit
i (0 <= i < NSCds) is set to '1', the respective downstream
sub-carrier i is part of a notch filter, and if set to '0',
the respective sub-carrier is not part of a notch filter.
This information complements the specification provided by
adsl2LConfProfPsdMaskDs.
Note that if NSCds < 512, all bits i (NSCds<i<512)
should be set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2.9"
::= { adsl2LineConfProfEntry 4 }
adsl2LConfProfRaModeDs OBJECT-TYPE
SYNTAX Adsl2RaMode
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The mode of operation of a rate-adaptive ATU-C in the transmit
direction. The parameter can take three values:
manual(1),
raInit(2), or
dynamicRa(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.1"
DEFVAL { manual }
::= { adsl2LineConfProfEntry 5 }
adsl2LConfProfRaModeUs OBJECT-TYPE
SYNTAX Adsl2RaMode
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The mode of operation of a rate-adaptive ATU-R in the transmit
direction. The parameter can take three values:
manual(1),
raInit(2), or
dynamicRa(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.2"
DEFVAL { manual }
::= { adsl2LineConfProfEntry 6 }
adsl2LConfProfRaUsNrmDs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 )
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Downstream Up-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is above this value and stays above it for
more than the time specified by the adsl2LConfProfRaUsTimeDs,
the ATU-R shall attempt to increase the downstream net data
rate. The Downstream Up-Shift Noise Margin ranges from 0 to
310 units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.3"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 7 }
adsl2LConfProfRaUsNrmUs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 )
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Upstream Up-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is above this value and stays above it for more
than the time specified by the adsl2LConfProfRaUsTimeUs, the
ATU-C shall attempt to increase the upstream net data rate.
The Upstream Up-Shift Noise Margin ranges from 0 to 310 units
of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.4"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 8 }
adsl2LConfProfRaUsTimeDs OBJECT-TYPE
SYNTAX Unsigned32 (0..16383 )
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Downstream Up-Shift Time Interval, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. The interval of
time that the downstream noise margin should stay above the
Downstream Up-Shift Noise Margin before the ATU-R shall
attempt to increase the downstream net data rate. The time
interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.5"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 9 }
adsl2LConfProfRaUsTimeUs OBJECT-TYPE
SYNTAX Unsigned32 (0..16383 )
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Upstream Up-Shift Time Interval, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay above the
Upstream Up-Shift Noise Margin before the ATU-C shall
attempt to increase the upstream net data rate. The time
interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.6"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 10 }
adsl2LConfProfRaDsNrmsDs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 )
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Downstream Down-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. If the downstream
noise margin is below this value and stays below that for more
than the time specified by the adsl2LConfProfRaDsTimeDs, the
ATU-R shall attempt to decrease the downstream net data rate.
The Downstream Down-Shift Noise Margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.7"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 11 }
adsl2LConfProfRaDsNrmsUs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 )
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Upstream Down-Shift Noise Margin value, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. If the upstream
noise margin is below this value and stays below that for more
than the time specified by the adsl2LConfProfRaDsTimeUs, the
ATU-C shall attempt to decrease the upstream net data rate.
The Upstream Down-Shift Noise Margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.8"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 12 }
adsl2LConfProfRaDsTimeDs OBJECT-TYPE
SYNTAX Unsigned32 (0..16383 )
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Downstream Down-Shift Time Interval, to be used when
adsl2LConfProfRaModeDs is set to dynamicRa. The interval of
time the downstream noise margin should stay below the
Downstream Down-Shift Noise Margin before the ATU-R shall
attempt to decrease the downstream net data rate. The time
interval ranges from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.9"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 13 }
adsl2LConfProfRaDsTimeUs OBJECT-TYPE
SYNTAX Unsigned32 (0..16383 )
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The Upstream Down-Shift Time Interval, to be used when
adsl2LConfProfRaModeUs is set to dynamicRa. The interval of
time the upstream noise margin should stay below the Upstream
Down-Shift Noise Margin before the ATU-C shall attempt to
decrease the upstream net data rate. The time interval ranges
from 0 to 16383 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.4.10"
DEFVAL { 3600 }
::= { adsl2LineConfProfEntry 14 }
adsl2LConfProfTargetSnrmDs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 )
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU-R receiver shall achieve,
relative to the BER requirement for each of the downstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.1"
DEFVAL { 60 }
::= { adsl2LineConfProfEntry 15 }
adsl2LConfProfTargetSnrmUs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 )
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU-C receiver shall achieve,
relative to the BER requirement for each of the upstream
bearer channels, to successfully complete initialization.
The target noise margin ranges from 0 to 310 units of 0.1 dB
(physical values are 0 to 31 dB)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.2"
DEFVAL { 60 }
::= { adsl2LineConfProfEntry 16 }
adsl2LConfProfMaxSnrmDs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum Noise Margin the ATU-R receiver shall try to
sustain. If the Noise Margin is above this level, the ATU-R
shall request that the ATU-C reduce the ATU-C transmit power
to get a noise margin below this limit (if this functionality
is supported). The maximum noise margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB). A value of
0x7FFFFFFF (2147483647) means that there is no maximum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.3"
DEFVAL { 310 }
::= { adsl2LineConfProfEntry 17 }
adsl2LConfProfMaxSnrmUs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 | 2147483647)
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum Noise Margin the ATU-C receiver shall try to
sustain. If the Noise Margin is above this level, the ATU-C
shall request that the ATU-R reduce the ATU-R transmit power
to get a noise margin below this limit (if this functionality
is supported). The maximum noise margin ranges from 0 to 310
units of 0.1 dB (physical values are 0 to 31 dB). A value of
0x7FFFFFFF (2147483647) means that there is no maximum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.4"
DEFVAL { 310 }
::= { adsl2LineConfProfEntry 18 }
adsl2LConfProfMinSnrmDs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 )
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU-R receiver shall tolerate.
If the noise margin falls below this level, the ATU-R shall
request that the ATU-C increase the ATU-C transmit power.
If an increase to ATU-C transmit power is not possible, a
loss-of-margin (LOM) defect occurs, the ATU-R shall fail and
attempt to reinitialize, and the NMS shall be notified. The
minimum noise margin ranges from 0 to 310 units of
0.1 dB (physical values are 0 to 31 dB). A value of 0 means
that there is no minimum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.5"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 19 }
adsl2LConfProfMinSnrmUs OBJECT-TYPE
SYNTAX Unsigned32 (0..310 )
UNITS "0.1 dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The minimum Noise Margin the ATU-C receiver shall tolerate.
If the noise margin falls below this level, the ATU-C shall
request that the ATU-R increase the ATU-R transmit power.
If an increase of ATU-R transmit power is not possible, a
loss-of-margin (LOM) defect occurs, the ATU-C shall fail and
attempt to reinitialize, and the NMS shall be notified. The
minimum noise margin ranges from 0 to 310 units of
0.1 dB (physical values are 0 to 31 dB). A value of 0 means
that there is no minimum."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.3.6"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 20 }
adsl2LConfProfMsgMinUs OBJECT-TYPE
SYNTAX Unsigned32 (4000..63000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Overhead Rate Upstream. Defines the minimum rate of
the message-based overhead that shall be maintained by the ATU
in upstream direction. Expressed in bits per second and
ranges from 4000 to 63000 bps."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.5.1"
DEFVAL { 4000 }
::= { adsl2LineConfProfEntry 21 }
adsl2LConfProfMsgMinDs OBJECT-TYPE
SYNTAX Unsigned32 (4000..63000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Overhead Rate Downstream. Defines the minimum rate of
the message-based overhead that shall be maintained by the ATU
in downstream direction. Expressed in bits per second and
ranges from 4000 to 63000 bps."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.5.2"
DEFVAL { 4000 }
::= { adsl2LineConfProfEntry 22 }
adsl2LConfProfAtuTransSysEna OBJECT-TYPE
SYNTAX Adsl2TransmissionModeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"ATU Transmission System Enabling (ATSE). A list of the
different coding types enabled in this profile. It is coded
in a bit-map representation with 1 or more bits set. A bit
set to '1' means that the ATUs may apply the respective
coding for the ADSL line. A bit set to '0' means that
the ATUs cannot apply the respective coding for the ADSL
line. All 'reserved' bits should be set to '0'."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.1"
::= { adsl2LineConfProfEntry 23 }
adsl2LConfProfPmMode OBJECT-TYPE
SYNTAX Adsl2LConfProfPmMode
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Power management state Enabling. Defines the power states the
ATU-C or ATU-R may autonomously transition to on this line.
The various bit positions are: allowTransitionsToIdle(0) and
allowTransitionsToLowPower(1). A bit with a '1' value means
that the ATU is allowed to transit into the respective state,
and a '0' value means that the ATU is not allowed
to transit into the respective state."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.4"
DEFVAL { { } }
::= { adsl2LineConfProfEntry 24 }
adsl2LConfProfL0Time OBJECT-TYPE
SYNTAX Unsigned32 (0..255 )
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This minimum time (in seconds) between an Exit from the L2
state and the next Entry into the L2 state. It ranges from 0
to 255 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.5"
DEFVAL { 255 }
::= { adsl2LineConfProfEntry 25 }
adsl2LConfProfL2Time OBJECT-TYPE
SYNTAX Unsigned32 (0..255 )
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This minimum time (in seconds) between an Entry into the
L2 state and the first Power Trim in the L2 state and between
two consecutive Power Trims in the L2 State.
It ranges from 0 to 255 seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.1.6"
DEFVAL { 255 }
::= { adsl2LineConfProfEntry 26 }
adsl2LConfProfL2Atpr OBJECT-TYPE
SYNTAX Unsigned32 (0..31 )
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum aggregate transmit power reduction (in dB) that
can be performed at transition of L0 to L2 state or through a
single Power Trim in the L2 state.
It ranges from 0 dB to 31 dB."
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.7"
DEFVAL { 10 }
::= { adsl2LineConfProfEntry 27 }
adsl2LConfProfL2Atprt OBJECT-TYPE
SYNTAX Unsigned32 (0..31 )
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The total maximum aggregate transmit power reduction
(in dB) that can be performed in an L2 state. This is the
sum of all reductions of L2 Request (i.e., at transition of
L0 to L2 state) and Power Trims."
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.1.9"
DEFVAL { 31 }
::= { adsl2LineConfProfEntry 28 }
adsl2LConfProfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or to modify or
delete an existing row in this table.
A profile is activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2LineConfProfEntry 29 }
-- ----------------------------------------
-- adsl2LineConfProfModeSpecTable --
-- ----------------------------------------
adsl2LineConfProfModeSpecTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineConfProfModeSpecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfProfModeSpecTable extends the
ADSL2 line configuration profile by ADSL Mode Specific
parameters.
A row in this table that has an index of
adsl2LConfProfAdslMode == defMode(1) is called a
'mandatory' row.
A row in this table that has an index such that
adsl2LConfProfAdslMode is not equal to defMode(1)
is called an 'optional' row.
When a row in the adsl2LineConfProfTable table
(the parent row) is created, the SNMP agent will
automatically create a 'mandatory' row in this table.
When the parent row is deleted, the SNMP agent will
automatically delete all associated rows in this table.
Any attempt to delete the 'mandatory' row using the
adsl2LConfProfModeSpecRowStatus attribute will be
rejected by the SNMP agent.
The manager MAY create an 'optional' row in this table
using the adsl2LConfProfModeSpecRowStatus attribute if
the parent row exists.
The manager MAY delete an 'optional' row in this table
using the adsl2LConfProfModeSpecRowStatus attribute at
any time.
If the actual transmission mode of a DSL line does not
match one of the 'optional' rows in this table, then
the line will use the PSD configuration from the
'mandatory' row.
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileLine 3 }
adsl2LineConfProfModeSpecEntry OBJECT-TYPE
SYNTAX Adsl2LineConfProfModeSpecEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineConfProfModeSpecTable extends the
ADSL2 line configuration profile by ADSL Mode Specific
parameters."
INDEX {
adsl2LConfProfProfileName,
adsl2LConfProfAdslMode
}
::= { adsl2LineConfProfModeSpecTable 1 }
Adsl2LineConfProfModeSpecEntry ::= SEQUENCE {
adsl2LConfProfAdslMode Adsl2OperationModes,
adsl2LConfProfMaxNomPsdDs Integer32,
adsl2LConfProfMaxNomPsdUs Integer32,
adsl2LConfProfMaxNomAtpDs Unsigned32,
adsl2LConfProfMaxNomAtpUs Unsigned32,
adsl2LConfProfMaxAggRxPwrUs Integer32,
adsl2LConfProfPsdMaskDs Adsl2PsdMaskDs,
adsl2LConfProfPsdMaskUs Adsl2PsdMaskUs,
adsl2LConfProfPsdMaskSelectUs Unsigned32,
adsl2LConfProfModeSpecRowStatus RowStatus
}
adsl2LConfProfAdslMode OBJECT-TYPE
SYNTAX Adsl2OperationModes
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ADSL Mode is a way of categorizing the various ADSL
transmission modes into groups; each group (ADSL Mode) shares
the same PSD configuration.
There should be multiple entries in this table for a given
line profile in case multiple bits are set in
adsl2LConfProfAtuTransSysEna for that profile."
REFERENCE "DSL Forum TR-90, paragraph 5.1.8"
::= { adsl2LineConfProfModeSpecEntry 1 }
adsl2LConfProfMaxNomPsdDs OBJECT-TYPE
SYNTAX Integer32 (-600..-300 )
UNITS "0.1 dBm/Hz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal transmit PSD in the downstream
direction during initialization and Showtime. It ranges from
-600 to -300 units of 0.1 dBm/Hz (physical values are -60 to
-30 dBm/Hz)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { -300 }
::= { adsl2LineConfProfModeSpecEntry 2 }
adsl2LConfProfMaxNomPsdUs OBJECT-TYPE
SYNTAX Integer32 (-600..-300 )
UNITS "0.1 dBm/Hz"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal transmit PSD in the upstream direction
during initialization and Showtime. It ranges from -600 to
-300 units of 0.1 dBm/Hz (physical values are -60 to
-30 dBm/Hz)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { -300 }
::= { adsl2LineConfProfModeSpecEntry 3 }
adsl2LConfProfMaxNomAtpDs OBJECT-TYPE
SYNTAX Unsigned32 (0..255 )
UNITS "0.1 dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal aggregate transmit power in the
downstream direction during initialization and Showtime. It
ranges from 0 to 255 units of 0.1 dBm (physical values are 0
to 25.5 dBm)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { 255 }
::= { adsl2LineConfProfModeSpecEntry 4 }
adsl2LConfProfMaxNomAtpUs OBJECT-TYPE
SYNTAX Unsigned32 (0..255 )
UNITS "0.1 dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum nominal aggregate transmit power in the upstream
direction during initialization and Showtime. It ranges from
0 to 255 units of 0.1 dBm (physical values are 0 to 25.5
dBm)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { 255 }
::= { adsl2LineConfProfModeSpecEntry 5 }
adsl2LConfProfMaxAggRxPwrUs OBJECT-TYPE
SYNTAX Integer32 (-255..255 | 2147483647)
UNITS "0.1 dBm"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The maximum upstream aggregate receive power over the relevant
set of sub-carriers. The ATU-C should verify that the
upstream power cutback is such that this maximum aggregate
receive power value is honored. It ranges from -255 to 255
units of 0.1 dBm (physical values are -25.5 to 25.5 dBm).
A value of 0x7FFFFFFF (2147483647) means that there is no
limit."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
DEFVAL { 255 }
::= { adsl2LineConfProfModeSpecEntry 6 }
adsl2LConfProfPsdMaskDs OBJECT-TYPE
SYNTAX Adsl2PsdMaskDs
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The downstream PSD mask applicable at the U-C2 reference
point.
This parameter is used only for G.992.5, and it may impose PSD
restrictions (breakpoints) in addition to the Limit PSD mask
defined in G.992.5.
This is a string of 32 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 94-95, which are
associated with a 32nd breakpoint.
Each subcarrier index is an unsigned number in the range 1 to
NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 32, all remaining
octets are set to the value 0. Note that the content of this
object should be correlated with the sub-carriers mask and with
the RFI setup."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
::= { adsl2LineConfProfModeSpecEntry 7 }
adsl2LConfProfPsdMaskUs OBJECT-TYPE
SYNTAX Adsl2PsdMaskUs
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The upstream PSD mask applicable at the U-R2 reference
point.
This parameter is used only for G.992.5, and it may impose PSD
restrictions (breakpoints) in addition to the Limit PSD mask
defined in G.992.5.
This is a string of 4 pairs of values in the following
structure:
Octets 0+1 - Index of 1st sub-carrier used in the context
of a first breakpoint.
Octet 2 - The PSD reduction for the sub-carrier indicated in
octets 0 and 1.
Octets 3-5 - Same, for a 2nd breakpoint.
Octets 6-8 - Same, for a 3rd breakpoint.
This architecture continues until octets 9-11, which are
associated with a 4th breakpoint.
Each subcarrier index is an unsigned number in the range 1 to
NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to
255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are
in the range 0 to 190 (0 to -95dBm/Hz).
When the number of breakpoints is less than 4, all remaining
octets are set to the value 0. Note that the content of this
object should be correlated with the sub-carriers mask and with
the RFI setup."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1.2"
::= { adsl2LineConfProfModeSpecEntry 8 }
adsl2LConfProfPsdMaskSelectUs OBJECT-TYPE
SYNTAX Unsigned32 (1..9 )
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The selected upstream PSD mask. This parameter is used only
for annexes J and M of G.992.3 and G.992.5, and the same
selection is used for all relevant enabled bits in
adsl2LConfProfAtuTransSysEna."
REFERENCE "ITU-T G.997.1 (amendment 1), 7.3.1.2.10"
DEFVAL { 1 }
::= { adsl2LineConfProfModeSpecEntry 9 }
adsl2LConfProfModeSpecRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or to modify or
delete an existing row in this table.
A profile is activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2LineConfProfModeSpecEntry 10 }
-- ----------------------------------------------
-- adsl2ChConfProfileTable --
-- ----------------------------------------------
adsl2ChConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChConfProfileTable contains ADSL2 channel
profile configuration.
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileChannel 1 }
adsl2ChConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2ChConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChConfProfileTable contains ADSL2 channel
profile configuration.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2ChConfProfProfileName }
::= { adsl2ChConfProfileTable 1 }
Adsl2ChConfProfileEntry ::= SEQUENCE {
adsl2ChConfProfProfileName SnmpAdminString,
adsl2ChConfProfMinDataRateDs Unsigned32,
adsl2ChConfProfMinDataRateUs Unsigned32,
adsl2ChConfProfMinResDataRateDs Unsigned32,
adsl2ChConfProfMinResDataRateUs Unsigned32,
adsl2ChConfProfMaxDataRateDs Unsigned32,
adsl2ChConfProfMaxDataRateUs Unsigned32,
adsl2ChConfProfMinDataRateLowPwrDs Unsigned32,
adsl2ChConfProfMaxDelayDs Unsigned32,
adsl2ChConfProfMaxDelayUs Unsigned32,
adsl2ChConfProfMinProtectionDs Adsl2SymbolProtection,
adsl2ChConfProfMinProtectionUs Adsl2SymbolProtection,
adsl2ChConfProfMaxBerDs Adsl2MaxBer,
adsl2ChConfProfMaxBerUs Adsl2MaxBer,
adsl2ChConfProfUsDataRateDs Unsigned32,
adsl2ChConfProfDsDataRateDs Unsigned32,
adsl2ChConfProfUsDataRateUs Unsigned32,
adsl2ChConfProfDsDataRateUs Unsigned32,
adsl2ChConfProfImaEnabled TruthValue,
adsl2ChConfProfRowStatus RowStatus
}
adsl2ChConfProfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2ChConfProfileEntry 1 }
adsl2ChConfProfMinDataRateDs OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Data Rate on Downstream direction. The minimum net
data rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 2 }
adsl2ChConfProfMinDataRateUs OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Data Rate on Upstream direction. The minimum net data
rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 3 }
adsl2ChConfProfMinResDataRateDs OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Reserved Data Rate on Downstream direction. The
minimum reserved net data rate for the bearer channel, coded
in bits/second. This parameter is used only if the Rate
Adaptation Mode in the direction of the bearer channel (i.e.,
adsl2LConfProfRaModeDs) is set to dynamicRa."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 4 }
adsl2ChConfProfMinResDataRateUs OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Reserved Data Rate on Upstream direction. The minimum
reserved net data rate for the bearer channel, coded in
bits/second. This parameter is used only if the Rate
Adaptation Mode in the direction of the bearer channel (i.e.,
adsl2LConfProfRaModeUs) is set to dynamicRa."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 5 }
adsl2ChConfProfMaxDataRateDs OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Data Rate on Downstream direction. The maximum net
data rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 6 }
adsl2ChConfProfMaxDataRateUs OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Data Rate on Upstream direction. The maximum net data
rate for the bearer channel, coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 7 }
adsl2ChConfProfMinDataRateLowPwrDs OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Data Rate in Low Power state on Downstream direction.
The minimum net data rate for the bearer channel, coded in
bits/second, during the low power state (L1 in G.992.2, L2 in
G.992.3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.1"
::= { adsl2ChConfProfileEntry 8 }
adsl2ChConfProfMaxDelayDs OBJECT-TYPE
SYNTAX Unsigned32 (0..63 )
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Interleave Delay on Downstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on
Downstream direction. The ATUs shall choose the S (factor)
and D (depth) values such that the actual one-way interleaving
delay (adsl2ChStatusActDelay) is as close as possible to,
but less than or equal to, adsl2ChConfProfMaxDelayDs. The
delay is coded in ms, with the value 0 indicating no delay
bound is being imposed."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.2"
::= { adsl2ChConfProfileEntry 9 }
adsl2ChConfProfMaxDelayUs OBJECT-TYPE
SYNTAX Unsigned32 (0..63 )
UNITS "milliseconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Interleave Delay on Upstream direction. The maximum
one-way interleaving delay introduced by the PMS-TC on
Upstream direction. The ATUs shall choose the S (factor) and
D (depth) values such that the actual one-way interleaving
delay (adsl2ChStatusActDelay) is as close as possible to,
but less than or equal to, adsl2ChConfProfMaxDelayUs. The
delay is coded in ms, with the value 0 indicating no delay
bound is being imposed."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.2"
::= { adsl2ChConfProfileEntry 10 }
adsl2ChConfProfMinProtectionDs OBJECT-TYPE
SYNTAX Adsl2SymbolProtection
UNITS "symbols"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Impulse Noise Protection on Downstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol), and 1-16 symbols in steps
of 1 symbol."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.3"
DEFVAL { noProtection }
::= { adsl2ChConfProfileEntry 11 }
adsl2ChConfProfMinProtectionUs OBJECT-TYPE
SYNTAX Adsl2SymbolProtection
UNITS "symbols"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Minimum Impulse Noise Protection on Upstream direction. The
minimum impulse noise protection for the bearer channel,
expressed in symbols. The parameter can take the following
values: noProtection (i.e., INP not required), halfSymbol
(i.e., INP length is 1/2 symbol), and 1-16 symbols in steps
of 1 symbol."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.3"
DEFVAL { noProtection }
::= { adsl2ChConfProfileEntry 12 }
adsl2ChConfProfMaxBerDs OBJECT-TYPE
SYNTAX Adsl2MaxBer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Bit Error Ratio on Downstream direction. The maximum
bit error ratio for the bearer channel. The parameter can
take the following values (for 1E-3, 1E-5 or 1E-7):
eminus3(1),
eminus5(2), or
eminus7(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.4"
DEFVAL { eminus5 }
::= { adsl2ChConfProfileEntry 13 }
adsl2ChConfProfMaxBerUs OBJECT-TYPE
SYNTAX Adsl2MaxBer
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Maximum Bit Error Ratio on Upstream direction. The maximum
bit error ratio for the bearer channel. The parameter can
take the following values (for 1E-3, 1E-5 or 1E-7):
eminus3(1),
eminus5(2), or
eminus7(3)."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.4"
DEFVAL { eminus5 }
::= { adsl2ChConfProfileEntry 14 }
adsl2ChConfProfUsDataRateDs OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Data Rate Threshold Up shift for downstream direction. An
'Up-shift rate change' event is triggered when the actual
downstream data rate exceeds, by more than the threshold, the
data rate at the last entry into Showtime. The parameter is
coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 15 }
adsl2ChConfProfDsDataRateDs OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Data Rate Threshold Down-shift for downstream direction. A
'Down-shift rate change' event is triggered when the actual
downstream data rate is below the data rate at the last entry
into Showtime, by more than the threshold. The parameter is
coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 16 }
adsl2ChConfProfUsDataRateUs OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Data Rate Threshold Up shift for upstream direction. An
'Up-shift rate change' event is triggered when the actual
upstream data rate exceeds, by more than the threshold, the
data rate at the last entry into Showtime. The parameter is
coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 17 }
adsl2ChConfProfDsDataRateUs OBJECT-TYPE
SYNTAX Unsigned32 (0..200000000 )
UNITS "bits/second"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Data Rate Threshold Down-shift for upstream direction. A
'Down-shift rate change' event is triggered when the actual
upstream data rate is below the data rate at the last entry
into Showtime, by more than the threshold. The parameter is
coded in bits/second."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2.6"
::= { adsl2ChConfProfileEntry 18 }
adsl2ChConfProfImaEnabled OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"IMA Mode Enable. The parameter enables the IMA operation mode
in the ATM Data Path. Relevant only if the channel is an ATM
Data Path. When in 'enable' state, the ATM data path should
comply with the requirements for IMA transmission."
REFERENCE "ITU-T G.997.1, paragraph 7.3.4.1"
DEFVAL { false }
::= { adsl2ChConfProfileEntry 19 }
adsl2ChConfProfRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or to modify or
delete an existing row in this table.
A profile is activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2ChConfProfileEntry 20 }
-- ----------------------------------------------
-- adsl2LineAlarmConfTemplateTable --
-- ----------------------------------------------
adsl2LineAlarmConfTemplateTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineAlarmConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineAlarmConfTemplateTable contains
ADSL2 line configuration templates.
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileAlarmConf 1 }
adsl2LineAlarmConfTemplateEntry OBJECT-TYPE
SYNTAX Adsl2LineAlarmConfTemplateEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineAlarmConfTemplateTable contains ADSL2
line PM thresholds templates.
A default template with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this
document."
INDEX { adsl2LAlarmConfTempTemplateName }
::= { adsl2LineAlarmConfTemplateTable 1 }
Adsl2LineAlarmConfTemplateEntry ::= SEQUENCE {
adsl2LAlarmConfTempTemplateName SnmpAdminString,
adsl2LAlarmConfTempLineProfile SnmpAdminString,
adsl2LAlarmConfTempChan1ConfProfile SnmpAdminString,
adsl2LAlarmConfTempChan2ConfProfile SnmpAdminString,
adsl2LAlarmConfTempChan3ConfProfile SnmpAdminString,
adsl2LAlarmConfTempChan4ConfProfile SnmpAdminString,
adsl2LAlarmConfTempRowStatus RowStatus
}
adsl2LAlarmConfTempTemplateName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2LineAlarmConfTemplateEntry 1 }
adsl2LAlarmConfTempLineProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2 Line
Thresholds Configuration Profile Table
(adsl2LineAlarmConfProfileTable) that applies to this ADSL2
line."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineAlarmConfTemplateEntry 2 }
adsl2LAlarmConfTempChan1ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #1. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "DEFVAL" }
::= { adsl2LineAlarmConfTemplateEntry 3 }
adsl2LAlarmConfTempChan2ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #2. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table. If the channel is unused,
then the object is set to a zero-length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 4 }
adsl2LAlarmConfTempChan3ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #3. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table.
This object may be set to a non-zero-length string only if
adsl2LAlarmConfTempChan2ConfProfile contains a non-zero-
length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 5 }
adsl2LAlarmConfTempChan4ConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (0..32))
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row in the ADSL2
Channel Thresholds Configuration Profile Table
(adsl2ChAlarmConfProfileTable) that applies for ADSL2
bearer channel #4. The channel profile name specified here
must match the name of an existing row in the
adsl2ChAlarmConfProfileTable table.
This object may be set to a non-zero-length string only if
adsl2LAlarmConfTempChan3ConfProfile contains a non-zero-
length string."
REFERENCE "DSL Forum TR-90, paragraph 5.4.1"
DEFVAL { "" }
::= { adsl2LineAlarmConfTemplateEntry 6 }
adsl2LAlarmConfTempRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or to modify or
delete an existing row in this table.
A template is activated by setting this object to 'active'.
When 'active' is set, the system will validate the template.
Before a template can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
lines."
::= { adsl2LineAlarmConfTemplateEntry 7 }
-- ----------------------------------------------
-- adsl2LineAlarmConfProfileTable --
-- ----------------------------------------------
adsl2LineAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2LineAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineAlarmConfProfileTable contains ADSL2
line PM thresholds profiles.
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileAlarmConf 2 }
adsl2LineAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2LineAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2LineAlarmConfProfileTable contains ADSL2
line PM thresholds profiles.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this
document."
INDEX { adsl2LineAlarmConfProfileName }
::= { adsl2LineAlarmConfProfileTable 1 }
Adsl2LineAlarmConfProfileEntry ::= SEQUENCE {
adsl2LineAlarmConfProfileName SnmpAdminString,
adsl2LineAlarmConfProfileAtucThresh15MinFecs HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinEs HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinSes HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinLoss HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAtucThresh15MinUas HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinFecs HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinEs HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinSes HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinLoss HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileAturThresh15MinUas HCPerfIntervalThreshold,
adsl2LineAlarmConfProfileThresh15MinFailedFullInt Unsigned32,
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt Unsigned32,
adsl2LineAlarmConfProfileRowStatus RowStatus
}
adsl2LineAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2LineAlarmConfProfileEntry 1 }
adsl2LineAlarmConfProfileAtucThresh15MinFecs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MFecs counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 2 }
adsl2LineAlarmConfProfileAtucThresh15MinEs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MEs counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 3 }
adsl2LineAlarmConfProfileAtucThresh15MinSes OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MSes counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 4 }
adsl2LineAlarmConfProfileAtucThresh15MinLoss OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MLoss counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 5 }
adsl2LineAlarmConfProfileAtucThresh15MinUas OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MUas counter,
when adsl2PMLCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 6 }
adsl2LineAlarmConfProfileAturThresh15MinFecs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MFecs counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 7 }
adsl2LineAlarmConfProfileAturThresh15MinEs OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MEs counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 8 }
adsl2LineAlarmConfProfileAturThresh15MinSes OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MSes counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 9 }
adsl2LineAlarmConfProfileAturThresh15MinLoss OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MLoss counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 10 }
adsl2LineAlarmConfProfileAturThresh15MinUas OBJECT-TYPE
SYNTAX HCPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurr15MUas counter,
when adsl2PMLCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 11 }
adsl2LineAlarmConfProfileThresh15MinFailedFullInt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurrInit15MfailedFullInits
counter.
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 12 }
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMLCurrInit15MFailedShortInits
counter.
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.1"
DEFVAL { 0 }
::= { adsl2LineAlarmConfProfileEntry 13 }
adsl2LineAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or to modify or
delete an existing row in this table.
A profile is activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2LineAlarmConfProfileEntry 14 }
-- ----------------------------------------------
-- adsl2ChAlarmConfProfileTable --
-- ----------------------------------------------
adsl2ChAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2ChAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChAlarmConfProfileTable contains ADSL2
channel PM thresholds profiles.
Entries in this table MUST be maintained in a
persistent manner."
::= { adsl2ProfileAlarmConf 3 }
adsl2ChAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Adsl2ChAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2ChAlarmConfProfileTable contains ADSL2
channel PM thresholds profiles.
A default profile with an index of 'DEFVAL' will
always exist, and its parameters will be set to vendor-
specific values, unless otherwise specified in this document."
INDEX { adsl2ChAlarmConfProfileName }
::= { adsl2ChAlarmConfProfileTable 1 }
Adsl2ChAlarmConfProfileEntry ::= SEQUENCE {
adsl2ChAlarmConfProfileName SnmpAdminString,
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations Unsigned32,
adsl2ChAlarmConfProfileAtucThresh15MinCorrected Unsigned32,
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations Unsigned32,
adsl2ChAlarmConfProfileAturThresh15MinCorrected Unsigned32,
adsl2ChAlarmConfProfileRowStatus RowStatus
}
adsl2ChAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE (1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object identifies a row in this table."
::= { adsl2ChAlarmConfProfileEntry 1 }
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMChCurr15MCodingViolations
counter, when adsl2PMChCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 2 }
adsl2ChAlarmConfProfileAtucThresh15MinCorrected OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMChCurr15MCorrectedBlocks
counter, when adsl2PMChCurrUnit is atuc(1).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 3 }
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMChCurr15MCodingViolations
counter, when adsl2PMChCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 4 }
adsl2ChAlarmConfProfileAturThresh15MinCorrected OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"A threshold for the adsl2PMChCurr15MCorrectedBlocks
counter, when adsl2PMChCurrUnit is atur(2).
The value 0 means that no threshold is specified for the
associated counter."
REFERENCE "ITU-T G.997.1, paragraph 7.3.2"
DEFVAL { 0 }
::= { adsl2ChAlarmConfProfileEntry 5 }
adsl2ChAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create a new row or to modify or
delete an existing row in this table.
A profile is activated by setting this object to 'active'.
When 'active' is set, the system will validate the profile.
Before a profile can be deleted or taken out of service
(by setting this object to 'destroy' or 'notInService'),
it must first be unreferenced from all associated
templates."
::= { adsl2ChAlarmConfProfileEntry 6 }
-- ----------------------------------------------
-- PM line current counters --
-- ----------------------------------------------
adsl2PMLineCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 lines."
::= { adsl2PMLine 1 }
adsl2PMLineCurrEntry OBJECT-TYPE
SYNTAX Adsl2PMLineCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrTable contains current Performance
Monitoring results of ADSL2 lines.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), along with a
termination unit.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
INDEX {
ifIndex,
adsl2PMLCurrUnit
}
::= { adsl2PMLineCurrTable 1 }
Adsl2PMLineCurrEntry ::= SEQUENCE {
adsl2PMLCurrUnit Adsl2Unit,
adsl2PMLCurrValidIntervals Unsigned32,
adsl2PMLCurrInvalidIntervals Unsigned32,
adsl2PMLCurr15MTimeElapsed HCPerfTimeElapsed,
adsl2PMLCurr15MFecs Counter32,
adsl2PMLCurr15MEs Counter32,
adsl2PMLCurr15MSes Counter32,
adsl2PMLCurr15MLoss Counter32,
adsl2PMLCurr15MUas Counter32,
adsl2PMLCurr1DayValidIntervals Unsigned32,
adsl2PMLCurr1DayInvalidIntervals Unsigned32,
adsl2PMLCurr1DayTimeElapsed HCPerfTimeElapsed,
adsl2PMLCurr1DayFecs Counter32,
adsl2PMLCurr1DayEs Counter32,
adsl2PMLCurr1DaySes Counter32,
adsl2PMLCurr1DayLoss Counter32,
adsl2PMLCurr1DayUas Counter32
}
adsl2PMLCurrUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit atuc(1) or atur(2)."
::= { adsl2PMLineCurrEntry 1 }
adsl2PMLCurrValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMLineCurrEntry 2 }
adsl2PMLCurrInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMLineCurrEntry 3 }
adsl2PMLCurr15MTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrEntry 4 }
adsl2PMLCurr15MFecs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 5 }
adsl2PMLCurr15MEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >=1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >=1 OR RDI >=1 OR LPR-FE >=1 .
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 6 }
adsl2PMLCurr15MSes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1 .
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 7 }
adsl2PMLCurr15MLoss OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was LOS (or
LOS-FE for ATU-R)."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 8 }
adsl2PMLCurr15MUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this
interval. Unavailability begins at the onset of 10
contiguous severely-errored seconds, and ends at the
onset of 10 contiguous seconds with no severely-errored
seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 9 }
adsl2PMLCurr1DayValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMLineCurrEntry 10 }
adsl2PMLCurr1DayInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMLineCurrEntry 11 }
adsl2PMLCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrEntry 12 }
adsl2PMLCurr1DayFecs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 13 }
adsl2PMLCurr1DayEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 14 }
adsl2PMLCurr1DaySes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 15 }
adsl2PMLCurr1DayLoss OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was LOS (or
LOS-FE for ATU-R)."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 16 }
adsl2PMLCurr1DayUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely-
errored seconds, and ends at the onset of 10 contiguous
seconds with no severely-errored seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrEntry 17 }
-- ----------------------------------------------
-- PM line init current counters --
-- ----------------------------------------------
adsl2PMLineCurrInitTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineCurrInitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrInitTable contains current
initialization counters of the ADSL2 line.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLine 2 }
adsl2PMLineCurrInitEntry OBJECT-TYPE
SYNTAX Adsl2PMLineCurrInitEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineCurrInitTable contains current
initialization counters of the ADSL2 line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), and a
termination unit."
INDEX { ifIndex }
::= { adsl2PMLineCurrInitTable 1 }
Adsl2PMLineCurrInitEntry ::= SEQUENCE {
adsl2PMLCurrInit15MTimeElapsed Unsigned32,
adsl2PMLCurrInit15MFullInits Unsigned32,
adsl2PMLCurrInit15MFailedFullInits Unsigned32,
adsl2PMLCurrInit15MShortInits Unsigned32,
adsl2PMLCurrInit15MFailedShortInits Unsigned32,
adsl2PMLCurrInit1DayTimeElapsed Unsigned32,
adsl2PMLCurrInit1DayFullInits Unsigned32,
adsl2PMLCurrInit1DayFailedFullInits Unsigned32,
adsl2PMLCurrInit1DayShortInits Unsigned32,
adsl2PMLCurrInit1DayFailedShortInits Unsigned32
}
adsl2PMLCurrInit15MTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrInitEntry 1 }
adsl2PMLCurrInit15MFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 2 }
adsl2PMLCurrInit15MFailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 3 }
adsl2PMLCurrInit15MShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 4 }
adsl2PMLCurrInit15MFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 5 }
adsl2PMLCurrInit1DayTimeElapsed OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMLineCurrInitEntry 6 }
adsl2PMLCurrInit1DayFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 7 }
adsl2PMLCurrInit1DayFailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 8 }
adsl2PMLCurrInit1DayShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 9 }
adsl2PMLCurrInit1DayFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineCurrInitEntry 10 }
-- -----------------------------------------
-- PM line history 15 Minutes --
-- -----------------------------------------
adsl2PMLineHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineHist15MinTable contains PM line history
for 15min intervals of the ADSL2 line."
::= { adsl2PMLine 3 }
adsl2PMLineHist15MinEntry OBJECT-TYPE
SYNTAX Adsl2PMLineHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineHist15MinTable contains PM line history
for 15min intervals of the ADSL2 line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), along with a
termination unit, and an interval number."
INDEX {
ifIndex,
adsl2PMLHist15MUnit,
adsl2PMLHist15MInterval
}
::= { adsl2PMLineHist15MinTable 1 }
Adsl2PMLineHist15MinEntry ::= SEQUENCE {
adsl2PMLHist15MUnit Adsl2Unit,
adsl2PMLHist15MInterval Unsigned32,
adsl2PMLHist15MMonitoredTime Unsigned32,
adsl2PMLHist15MFecs Counter32,
adsl2PMLHist15MEs Counter32,
adsl2PMLHist15MSes Counter32,
adsl2PMLHist15MLoss Counter32,
adsl2PMLHist15MUas Counter32,
adsl2PMLHist15MValidInterval TruthValue
}
adsl2PMLHist15MUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit atuc(1) or atur(2)."
::= { adsl2PMLineHist15MinEntry 1 }
adsl2PMLHist15MInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..96 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineHist15MinEntry 2 }
adsl2PMLHist15MMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineHist15MinEntry 3 }
adsl2PMLHist15MFecs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 4 }
adsl2PMLHist15MEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 5 }
adsl2PMLHist15MSes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 6 }
adsl2PMLHist15MLoss OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was LOS (or
LOS-FE for ATU-R)."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 7 }
adsl2PMLHist15MUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely-
errored seconds, and ends at the onset of 10 contiguous
seconds with no severely-errored seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist15MinEntry 8 }
adsl2PMLHist15MValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineHist15MinEntry 9 }
-- -------------------------------------
-- PM line history 1 Day --
-- -------------------------------------
adsl2PMLineHist1DayTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineHist1DayTable contains PM line history
for 24-hour intervals of the ADSL2 line."
::= { adsl2PMLine 4 }
adsl2PMLineHist1DayEntry OBJECT-TYPE
SYNTAX Adsl2PMLineHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineHist1DayTable contains PM line history
for 24-hour intervals of the ADSL2 line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), along with a
termination unit, and an interval number."
INDEX {
ifIndex,
adsl2PMLHist1DUnit,
adsl2PMLHist1DInterval
}
::= { adsl2PMLineHist1DayTable 1 }
Adsl2PMLineHist1DayEntry ::= SEQUENCE {
adsl2PMLHist1DUnit Adsl2Unit,
adsl2PMLHist1DInterval Unsigned32,
adsl2PMLHist1DMonitoredTime Unsigned32,
adsl2PMLHist1DFecs Counter32,
adsl2PMLHist1DEs Counter32,
adsl2PMLHist1DSes Counter32,
adsl2PMLHist1DLoss Counter32,
adsl2PMLHist1DUas Counter32,
adsl2PMLHist1DValidInterval TruthValue
}
adsl2PMLHist1DUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMLineHist1DayEntry 1 }
adsl2PMLHist1DInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..30 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineHist1DayEntry 2 }
adsl2PMLHist1DMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineHist1DayEntry 3 }
adsl2PMLHist1DFecs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was at least
one FEC correction event for one or more bearer channels in
this line. This parameter is inhibited during UAS or SES."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 4 }
adsl2PMLHist1DEs OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: CRC-8 >= 1 for one or more bearer channels OR
LOS >= 1 OR SEF >= 1 OR LPR >= 1
ATU-R: FEBE >= 1 for one or more bearer channels OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 5 }
adsl2PMLHist1DSes OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was:
ATU-C: (CRC-8 summed over all bearer channels) >= 18 OR
LOS >= 1 OR SEF >> 1 OR LPR >= 1
ATU-R: (FEBE summed over all bearer channels) >= 18 OR
LOS-FE >= 1 OR RDI >= 1 OR LPR-FE >= 1.
This parameter is inhibited during UAS."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 6 }
adsl2PMLHist1DLoss OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds during this interval where there was LOS (or
LOS-FE for ATU-R)."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 7 }
adsl2PMLHist1DUas OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of seconds in Unavailability State during this interval.
Unavailability begins at the onset of 10 contiguous severely-
errored seconds, and ends at the onset of 10 contiguous
seconds with no severely-errored seconds."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineHist1DayEntry 8 }
adsl2PMLHist1DValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineHist1DayEntry 9 }
-- -----------------------------------------
-- PM line init history 15 Minutes --
-- -----------------------------------------
adsl2PMLineInitHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineInitHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineInitHist15MinTable contains PM line
initialization history for 15-minute intervals of the ADSL2
line."
::= { adsl2PMLine 5 }
adsl2PMLineInitHist15MinEntry OBJECT-TYPE
SYNTAX Adsl2PMLineInitHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineInitHist15MinTable contains PM line
initialization history for 15 minutes intervals of the ADSL2
line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), and an interval
number."
INDEX {
ifIndex,
adsl2PMLHistInit15MInterval
}
::= { adsl2PMLineInitHist15MinTable 1 }
Adsl2PMLineInitHist15MinEntry ::= SEQUENCE {
adsl2PMLHistInit15MInterval Unsigned32,
adsl2PMLHistInit15MMonitoredTime Unsigned32,
adsl2PMLHistInit15MFullInits Unsigned32,
adsl2PMLHistInit15MFailedFullInits Unsigned32,
adsl2PMLHistInit15MShortInits Unsigned32,
adsl2PMLHistInit15MFailedShortInits Unsigned32,
adsl2PMLHistInit15MValidInterval TruthValue
}
adsl2PMLHistInit15MInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..96 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineInitHist15MinEntry 1 }
adsl2PMLHistInit15MMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineInitHist15MinEntry 2 }
adsl2PMLHistInit15MFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 3 }
adsl2PMLHistInit15MFailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 4 }
adsl2PMLHistInit15MShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 5 }
adsl2PMLHistInit15MFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist15MinEntry 6 }
adsl2PMLHistInit15MValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineInitHist15MinEntry 7 }
-- -----------------------------------------
-- PM line init history 1 Day --
-- -----------------------------------------
adsl2PMLineInitHist1DayTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMLineInitHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineInitHist1DayTable contains PM line
initialization history for 24-hour intervals of the ADSL2
line."
::= { adsl2PMLine 6 }
adsl2PMLineInitHist1DayEntry OBJECT-TYPE
SYNTAX Adsl2PMLineInitHist1DayEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMLineInitHist1DayTable contains PM line
initialization history for 24-hour intervals of the ADSL2
line.
The index of this table consists of an interface index, where
the interface has an ifType of adsl2plus(238), and an interval
number."
INDEX {
ifIndex,
adsl2PMLHistinit1DInterval
}
::= { adsl2PMLineInitHist1DayTable 1 }
Adsl2PMLineInitHist1DayEntry ::= SEQUENCE {
adsl2PMLHistinit1DInterval Unsigned32,
adsl2PMLHistinit1DMonitoredTime Unsigned32,
adsl2PMLHistinit1DFullInits Unsigned32,
adsl2PMLHistinit1DFailedFullInits Unsigned32,
adsl2PMLHistinit1DShortInits Unsigned32,
adsl2PMLHistinit1DFailedShortInits Unsigned32,
adsl2PMLHistinit1DValidInterval TruthValue
}
adsl2PMLHistinit1DInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..30 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMLineInitHist1DayEntry 1 }
adsl2PMLHistinit1DMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMLineInitHist1DayEntry 2 }
adsl2PMLHistinit1DFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of full initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 3 }
adsl2PMLHistinit1DFailedFullInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed full initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 4 }
adsl2PMLHistinit1DShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of short initializations attempted on the line
(successful and failed) during this interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 5 }
adsl2PMLHistinit1DFailedShortInits OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of failed short initializations on the line during this
interval."
REFERENCE "ITU-T G.997.1, paragraph 7.2.1"
::= { adsl2PMLineInitHist1DayEntry 6 }
adsl2PMLHistinit1DValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMLineInitHist1DayEntry 7 }
-- -------------------------------------------------
-- PM channel current counters --
-- -------------------------------------------------
adsl2PMChCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The PM counters in the table are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMChannel 1 }
adsl2PMChCurrEntry OBJECT-TYPE
SYNTAX Adsl2PMChCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL channel, along with a termination unit."
INDEX {
ifIndex,
adsl2PMChCurrUnit
}
::= { adsl2PMChCurrTable 1 }
Adsl2PMChCurrEntry ::= SEQUENCE {
adsl2PMChCurrUnit Adsl2Unit,
adsl2PMChCurrValidIntervals Unsigned32,
adsl2PMChCurrInvalidIntervals Unsigned32,
adsl2PMChCurr15MTimeElapsed HCPerfTimeElapsed,
adsl2PMChCurr15MCodingViolations Unsigned32,
adsl2PMChCurr15MCorrectedBlocks Unsigned32,
adsl2PMChCurr1DayValidIntervals Unsigned32,
adsl2PMChCurr1DayInvalidIntervals Unsigned32,
adsl2PMChCurr1DayTimeElapsed HCPerfTimeElapsed,
adsl2PMChCurr1DayCodingViolations Unsigned32,
adsl2PMChCurr1DayCorrectedBlocks Unsigned32
}
adsl2PMChCurrUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMChCurrEntry 1 }
adsl2PMChCurrValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMChCurrEntry 2 }
adsl2PMChCurrInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMChCurrEntry 3 }
adsl2PMChCurr15MTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMChCurrEntry 4 }
adsl2PMChCurr15MCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the
channel during the interval. This parameter is inhibited
during UAS or SES. If the CRC is applied over multiple
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 5 }
adsl2PMChCurr15MCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 6 }
adsl2PMChCurr1DayValidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Valid intervals."
::= { adsl2PMChCurrEntry 7 }
adsl2PMChCurr1DayInvalidIntervals OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Invalid intervals."
::= { adsl2PMChCurrEntry 8 }
adsl2PMChCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX HCPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds since this PM interval began.
Note that the PM counters are not reset even when the XTU
is reinitialized. They are reinitialized only when the
agent itself is reset or reinitialized."
::= { adsl2PMChCurrEntry 9 }
adsl2PMChCurr1DayCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the
channel during the interval. This parameter is inhibited
during UAS or SES. If the CRC is applied over multiple
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 10 }
adsl2PMChCurr1DayCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChCurrEntry 11 }
-- -----------------------------------------
-- PM channel history 15 Minutes --
-- -----------------------------------------
adsl2PMChHist15MinTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel."
::= { adsl2PMChannel 2 }
adsl2PMChHist15MinEntry OBJECT-TYPE
SYNTAX Adsl2PMChHist15MinEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChCurrTable contains current Performance
Monitoring results of the ADSL2 channel.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL channel, along with a termination unit, and the
interval number."
INDEX {
ifIndex,
adsl2PMChHist15MUnit,
adsl2PMChHist15MInterval
}
::= { adsl2PMChHist15MinTable 1 }
Adsl2PMChHist15MinEntry ::= SEQUENCE {
adsl2PMChHist15MUnit Adsl2Unit,
adsl2PMChHist15MInterval Unsigned32,
adsl2PMChHist15MMonitoredTime Unsigned32,
adsl2PMChHist15MCodingViolations Unsigned32,
adsl2PMChHist15MCorrectedBlocks Unsigned32,
adsl2PMChHist15MValidInterval TruthValue
}
adsl2PMChHist15MUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMChHist15MinEntry 1 }
adsl2PMChHist15MInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..96 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMChHist15MinEntry 2 }
adsl2PMChHist15MMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMChHist15MinEntry 3 }
adsl2PMChHist15MCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the
channel during the interval. This parameter is inhibited
during UAS or SES. If the CRC is applied over multiple
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist15MinEntry 4 }
adsl2PMChHist15MCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist15MinEntry 5 }
adsl2PMChHist15MValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMChHist15MinEntry 6 }
-- ----------------------------------------
-- PM channel history 1 Day --
-- ----------------------------------------
adsl2PMChHist1DTable OBJECT-TYPE
SYNTAX SEQUENCE OF Adsl2PMChHist1DEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChHist1DayTable contains PM channel history
for 1-day intervals of ADSL2."
::= { adsl2PMChannel 3 }
adsl2PMChHist1DEntry OBJECT-TYPE
SYNTAX Adsl2PMChHist1DEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table adsl2PMChHist1DayTable contains PM channel history
for 1-day intervals of ADSL2.
The index of this table consists of an interface index, where
the interface has an ifType value that is applicable
for a DSL channel, along with a termination unit, and the
interval number."
INDEX {
ifIndex,
adsl2PMChHist1DUnit,
adsl2PMChHist1DInterval
}
::= { adsl2PMChHist1DTable 1 }
Adsl2PMChHist1DEntry ::= SEQUENCE {
adsl2PMChHist1DUnit Adsl2Unit,
adsl2PMChHist1DInterval Unsigned32,
adsl2PMChHist1DMonitoredTime Unsigned32,
adsl2PMChHist1DCodingViolations Unsigned32,
adsl2PMChHist1DCorrectedBlocks Unsigned32,
adsl2PMChHist1DValidInterval TruthValue
}
adsl2PMChHist1DUnit OBJECT-TYPE
SYNTAX Adsl2Unit
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The termination unit."
::= { adsl2PMChHist1DEntry 1 }
adsl2PMChHist1DInterval OBJECT-TYPE
SYNTAX Unsigned32 (1..30 )
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The interval number."
::= { adsl2PMChHist1DEntry 2 }
adsl2PMChHist1DMonitoredTime OBJECT-TYPE
SYNTAX Unsigned32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total seconds monitored in this interval."
::= { adsl2PMChHist1DEntry 3 }
adsl2PMChHist1DCodingViolations OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC-8 (FEBE for ATU-R) anomalies occurring in the
channel during the interval. This parameter is inhibited
during UAS or SES. If the CRC is applied over multiple
channels, then each related CRC-8 (or FEBE) anomaly should
increment each of the counters related to the individual
channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist1DEntry 4 }
adsl2PMChHist1DCorrectedBlocks OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of FEC (FFEC for ATU-R) anomalies (corrected code words)
occurring in the channel during the interval. This parameter
is inhibited during UAS or SES. If the FEC is applied over
multiple channels, then each related FEC (or FFEC) anomaly
should increment each of the counters related to the
individual channels."
REFERENCE "ITU-T G.997.1, paragraph 7.2.2"
::= { adsl2PMChHist1DEntry 5 }
adsl2PMChHist1DValidInterval OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if the data for this interval is
valid."
::= { adsl2PMChHist1DEntry 6 }
-- -----------------------------------------
-- Notifications Group --
-- -----------------------------------------
adsl2LinePerfFECSThreshAtuc NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurr15MFecs,
adsl2LineAlarmConfProfileAtucThresh15MinFecs
}
STATUS current
DESCRIPTION
"This notification indicates that the FEC seconds threshold
has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 1 }
adsl2LinePerfFECSThreshAtur NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurr15MFecs,
adsl2LineAlarmConfProfileAturThresh15MinFecs
}
STATUS current
DESCRIPTION
"This notification indicates that the FEC seconds threshold
has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 2 }
adsl2LinePerfESThreshAtuc NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurr15MEs,
adsl2LineAlarmConfProfileAtucThresh15MinEs
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds threshold
has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 3 }
adsl2LinePerfESThreshAtur NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurr15MEs,
adsl2LineAlarmConfProfileAturThresh15MinEs
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds threshold
has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 4 }
adsl2LinePerfSESThreshAtuc NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurr15MSes,
adsl2LineAlarmConfProfileAtucThresh15MinSes
}
STATUS current
DESCRIPTION
"This notification indicates that the severely-errored seconds
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 5 }
adsl2LinePerfSESThreshAtur NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurr15MSes,
adsl2LineAlarmConfProfileAturThresh15MinSes
}
STATUS current
DESCRIPTION
"This notification indicates that the severely-errored seconds
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 6 }
adsl2LinePerfLOSSThreshAtuc NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurr15MLoss,
adsl2LineAlarmConfProfileAtucThresh15MinLoss
}
STATUS current
DESCRIPTION
"This notification indicates that the LOS seconds
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 7 }
adsl2LinePerfLOSSThreshAtur NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurr15MLoss,
adsl2LineAlarmConfProfileAturThresh15MinLoss
}
STATUS current
DESCRIPTION
"This notification indicates that the LOS seconds
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 8 }
adsl2LinePerfUASThreshAtuc NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurr15MUas,
adsl2LineAlarmConfProfileAtucThresh15MinUas
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 9 }
adsl2LinePerfUASThreshAtur NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurr15MUas,
adsl2LineAlarmConfProfileAturThresh15MinUas
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 10 }
adsl2LinePerfCodingViolationsThreshAtuc NOTIFICATION-TYPE
OBJECTS {
adsl2PMChCurr15MCodingViolations,
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations
}
STATUS current
DESCRIPTION
"This notification indicates that the coding violations
threshold has been reached/exceeded for the referred ATU-C."
::= { adsl2Notifications 11 }
adsl2LinePerfCodingViolationsThreshAtur NOTIFICATION-TYPE
OBJECTS {
adsl2PMChCurr15MCodingViolations,
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations
}
STATUS current
DESCRIPTION
"This notification indicates that the coding violations
threshold has been reached/exceeded for the referred ATU-R."
::= { adsl2Notifications 12 }
adsl2LinePerfCorrectedThreshAtuc NOTIFICATION-TYPE
OBJECTS {
adsl2PMChCurr15MCorrectedBlocks,
adsl2ChAlarmConfProfileAtucThresh15MinCorrected
}
STATUS current
DESCRIPTION
"This notification indicates that the corrected blocks
(FEC events) threshold has been reached/exceeded for the
referred ATU-C."
::= { adsl2Notifications 13 }
adsl2LinePerfCorrectedThreshAtur NOTIFICATION-TYPE
OBJECTS {
adsl2PMChCurr15MCorrectedBlocks,
adsl2ChAlarmConfProfileAturThresh15MinCorrected
}
STATUS current
DESCRIPTION
"This notification indicates that the corrected blocks
(FEC events) threshold has been reached/exceeded for the
referred ATU-R."
::= { adsl2Notifications 14 }
adsl2LinePerfFailedFullInitThresh NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurrInit15MFailedFullInits,
adsl2LineAlarmConfProfileThresh15MinFailedFullInt
}
STATUS current
DESCRIPTION
"This notification indicates that the failed full
initializations threshold has been reached/exceeded for the
referred ADSL/ADSL2 or ADSL2+ line."
::= { adsl2Notifications 15 }
adsl2LinePerfFailedShortInitThresh NOTIFICATION-TYPE
OBJECTS {
adsl2PMLCurrInit15MFailedShortInits,
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt
}
STATUS current
DESCRIPTION
"This notification indicates that the failed short
initializations threshold has been reached/exceeded for the
referred ADSL/ADSL2 or ADSL2+ line."
::= { adsl2Notifications 16 }
adsl2LineStatusChangeAtuc NOTIFICATION-TYPE
OBJECTS { adsl2LineStatusAtuc }
STATUS current
DESCRIPTION
"This notification indicates that a status change is
detected for the referred ATU-C."
::= { adsl2Notifications 17 }
adsl2LineStatusChangeAtur NOTIFICATION-TYPE
OBJECTS { adsl2LineStatusAtur }
STATUS current
DESCRIPTION
"This notification indicates that a status change is
detected for the referred ATU-R."
::= { adsl2Notifications 18 }
-- conformance information
adsl2Groups OBJECT IDENTIFIER
::= { adsl2Conformance 1 }
adsl2Compliances OBJECT IDENTIFIER
::= { adsl2Conformance 2 }
adsl2LineMibCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities that
manage ADSL/ADSL2 or ADSL2+ interfaces."
MODULE -- this module
MANDATORY-GROUPS {
adsl2LineGroup,
adsl2ChannelStatusGroup,
adsl2SCStatusGroup,
adsl2LineInventoryGroup,
adsl2LineConfTemplateGroup,
adsl2LineConfProfGroup,
adsl2LineConfProfModeSpecGroup,
adsl2ChConfProfileGroup,
adsl2LineAlarmConfTemplateGroup,
adsl2PMLineCurrGroup,
adsl2PMLineCurrInitGroup,
adsl2PMLineHist15MinGroup,
adsl2PMLineHist1DayGroup,
adsl2PMLineInitHist15MinGroup,
adsl2PMLineInitHist1DayGroup,
adsl2PMChCurrGroup,
adsl2PMChHist15MinGroup,
adsl2PMChHist1DGroup
}
GROUP adsl2ChannelStatusAtmGroup
DESCRIPTION
"The group of status objects required when the data path
is ATM."
GROUP adsl2ChannelStatusPtmGroup
DESCRIPTION
"The group of status objects required when the data path
is PTM."
GROUP adsl2LineConfProfRaGroup
DESCRIPTION
"The group of objects required for controlling the rate-
adaptive behavior of the line."
GROUP adsl2LineConfProfMsgMinGroup
DESCRIPTION
"The group of objects required for controlling the rate
reserved for Overhead traffic."
GROUP adsl2LineAlarmConfProfileGroup
DESCRIPTION
"The group of objects that define the alarm thresholds
on line-level PM counters."
GROUP adsl2ChAlarmConfProfileGroup
DESCRIPTION
"The group of objects that define the alarm thresholds
on channel-level PM counters."
GROUP adsl2ChConfProfileAtmGroup
DESCRIPTION
"The group of configuration objects required when the data
path is ATM."
GROUP adsl2ChConfProfileMinResGroup
DESCRIPTION
"The group of configuration objects required for the
reserved data rate."
GROUP adsl2PMLineCurrInitShortGroup
DESCRIPTION
"The group of PM counters for the current interval's
short initializations."
GROUP adsl2PMLineInitHist15MinShortGroup
DESCRIPTION
"The group of PM counters for the previous 15-minute
interval's short initializations."
GROUP adsl2PMLineInitHist1DayShortGroup
DESCRIPTION
"The group of PM counters for the previous 24-hour
interval's short initializations."
GROUP adsl2ScalarSCGroup
DESCRIPTION
"The group of objects that report the available memory
resources for DELT processes."
GROUP adsl2ThreshNotificationGroup
DESCRIPTION
"The group of threshold crossing notifications."
GROUP adsl2StatusChangeNotificationGroup
DESCRIPTION
"The group of status change notifications."
::= { adsl2Compliances 1 }
-- units of conformance
adsl2LineGroup OBJECT-GROUP
OBJECTS {
adsl2LineCnfgTemplate,
adsl2LineAlarmCnfgTemplate,
adsl2LineCmndConfPmsf,
adsl2LineCmndConfLdsf,
adsl2LineCmndConfLdsfFailReason,
adsl2LineCmndAutomodeColdStart,
adsl2LineStatusAtuTransSys,
adsl2LineStatusPwrMngState,
adsl2LineStatusInitResult,
adsl2LineStatusLastStateDs,
adsl2LineStatusLastStateUs,
adsl2LineStatusAtur,
adsl2LineStatusAtuc,
adsl2LineStatusLnAttenDs,
adsl2LineStatusLnAttenUs,
adsl2LineStatusSigAttenDs,
adsl2LineStatusSigAttenUs,
adsl2LineStatusSnrMarginDs,
adsl2LineStatusSnrMarginUs,
adsl2LineStatusAttainableRateDs,
adsl2LineStatusAttainableRateUs,
adsl2LineStatusActPsdDs,
adsl2LineStatusActPsdUs,
adsl2LineStatusActAtpDs,
adsl2LineStatusActAtpUs
}
STATUS current
DESCRIPTION
"The group of configuration, status, and commands objects
on the line level."
::= { adsl2Groups 1 }
adsl2ChannelStatusGroup OBJECT-GROUP
OBJECTS {
adsl2ChStatusChannelNum,
adsl2ChStatusActDataRate,
adsl2ChStatusPrevDataRate,
adsl2ChStatusActDelay
}
STATUS current
DESCRIPTION
"The group of status objects on the channel level."
::= { adsl2Groups 2 }
adsl2ChannelStatusAtmGroup OBJECT-GROUP
OBJECTS { adsl2ChStatusAtmStatus }
STATUS current
DESCRIPTION
"The group of status objects on the data path level
when it is ATM."
::= { adsl2Groups 3 }
adsl2ChannelStatusPtmGroup OBJECT-GROUP
OBJECTS { adsl2ChStatusPtmStatus }
STATUS current
DESCRIPTION
"The group of status objects on the data path level
when it is PTM."
::= { adsl2Groups 4 }
adsl2SCStatusGroup OBJECT-GROUP
OBJECTS {
adsl2SCStatusMtime,
adsl2SCStatusSnr,
adsl2SCStatusBitsAlloc,
adsl2SCStatusGainAlloc,
adsl2SCStatusTssi,
adsl2SCStatusLinScale,
adsl2SCStatusLinReal,
adsl2SCStatusLinImg,
adsl2SCStatusLogMt,
adsl2SCStatusLog,
adsl2SCStatusQlnMt,
adsl2SCStatusQln,
adsl2SCStatusLnAtten,
adsl2SCStatusSigAtten,
adsl2SCStatusSnrMargin,
adsl2SCStatusAttainableRate,
adsl2SCStatusActAtp,
adsl2SCStatusRowStatus
}
STATUS current
DESCRIPTION
"The group of status objects on the sub-carrier level.
They are updated as a result of a DELT process."
::= { adsl2Groups 5 }
adsl2LineInventoryGroup OBJECT-GROUP
OBJECTS {
adsl2LInvG994VendorId,
adsl2LInvSystemVendorId,
adsl2LInvVersionNumber,
adsl2LInvSerialNumber,
adsl2LInvSelfTestResult,
adsl2LInvTransmissionCapabilities
}
STATUS current
DESCRIPTION
"The group of inventory objects per XTU."
::= { adsl2Groups 6 }
adsl2LineConfTemplateGroup OBJECT-GROUP
OBJECTS {
adsl2LConfTempLineProfile,
adsl2LConfTempChan1ConfProfile,
adsl2LConfTempChan1RaRatioDs,
adsl2LConfTempChan1RaRatioUs,
adsl2LConfTempChan2ConfProfile,
adsl2LConfTempChan2RaRatioDs,
adsl2LConfTempChan2RaRatioUs,
adsl2LConfTempChan3ConfProfile,
adsl2LConfTempChan3RaRatioDs,
adsl2LConfTempChan3RaRatioUs,
adsl2LConfTempChan4ConfProfile,
adsl2LConfTempChan4RaRatioDs,
adsl2LConfTempChan4RaRatioUs,
adsl2LConfTempRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line configuration template."
::= { adsl2Groups 7 }
adsl2LineConfProfGroup OBJECT-GROUP
OBJECTS {
adsl2LConfProfScMaskDs,
adsl2LConfProfScMaskUs,
adsl2LConfProfRfiBandsDs,
adsl2LConfProfRaModeDs,
adsl2LConfProfRaModeUs,
adsl2LConfProfTargetSnrmDs,
adsl2LConfProfTargetSnrmUs,
adsl2LConfProfMaxSnrmDs,
adsl2LConfProfMaxSnrmUs,
adsl2LConfProfMinSnrmDs,
adsl2LConfProfMinSnrmUs,
adsl2LConfProfAtuTransSysEna,
adsl2LConfProfPmMode,
adsl2LConfProfL0Time,
adsl2LConfProfL2Time,
adsl2LConfProfL2Atpr,
adsl2LConfProfL2Atprt,
adsl2LConfProfRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line configuration profile."
::= { adsl2Groups 8 }
adsl2LineConfProfRaGroup OBJECT-GROUP
OBJECTS {
adsl2LConfProfRaUsNrmDs,
adsl2LConfProfRaUsNrmUs,
adsl2LConfProfRaUsTimeDs,
adsl2LConfProfRaUsTimeUs,
adsl2LConfProfRaDsNrmsDs,
adsl2LConfProfRaDsNrmsUs,
adsl2LConfProfRaDsTimeDs,
adsl2LConfProfRaDsTimeUs
}
STATUS current
DESCRIPTION
"The group of objects required for controlling the rate-
adaptive behavior of the line."
::= { adsl2Groups 9 }
adsl2LineConfProfMsgMinGroup OBJECT-GROUP
OBJECTS {
adsl2LConfProfMsgMinUs,
adsl2LConfProfMsgMinDs
}
STATUS current
DESCRIPTION
"The group of objects required for controlling the rate
reserved for Overhead traffic."
::= { adsl2Groups 10 }
adsl2LineConfProfModeSpecGroup OBJECT-GROUP
OBJECTS {
adsl2LConfProfMaxNomPsdDs,
adsl2LConfProfMaxNomPsdUs,
adsl2LConfProfMaxNomAtpDs,
adsl2LConfProfMaxNomAtpUs,
adsl2LConfProfMaxAggRxPwrUs,
adsl2LConfProfPsdMaskDs,
adsl2LConfProfPsdMaskUs,
adsl2LConfProfPsdMaskSelectUs,
adsl2LConfProfModeSpecRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line configuration profile
that have an instance for each operation mode allowed."
::= { adsl2Groups 11 }
adsl2ChConfProfileGroup OBJECT-GROUP
OBJECTS {
adsl2ChConfProfMinDataRateDs,
adsl2ChConfProfMinDataRateUs,
adsl2ChConfProfMaxDataRateDs,
adsl2ChConfProfMaxDataRateUs,
adsl2ChConfProfMinDataRateLowPwrDs,
adsl2ChConfProfMaxDelayDs,
adsl2ChConfProfMaxDelayUs,
adsl2ChConfProfMinProtectionDs,
adsl2ChConfProfMinProtectionUs,
adsl2ChConfProfMaxBerDs,
adsl2ChConfProfMaxBerUs,
adsl2ChConfProfUsDataRateDs,
adsl2ChConfProfDsDataRateDs,
adsl2ChConfProfUsDataRateUs,
adsl2ChConfProfDsDataRateUs,
adsl2ChConfProfRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a channel configuration profile."
::= { adsl2Groups 12 }
adsl2ChConfProfileAtmGroup OBJECT-GROUP
OBJECTS {
adsl2ChConfProfImaEnabled,
adsl2ChStatusAtmStatus
}
STATUS current
DESCRIPTION
"The group of configuration objects required when the data
path is ATM."
::= { adsl2Groups 13 }
adsl2ChConfProfileMinResGroup OBJECT-GROUP
OBJECTS {
adsl2ChConfProfMinResDataRateDs,
adsl2ChConfProfMinResDataRateUs
}
STATUS current
DESCRIPTION
"The group of configuration objects required for the
reserved data rate."
::= { adsl2Groups 14 }
adsl2LineAlarmConfTemplateGroup OBJECT-GROUP
OBJECTS {
adsl2LAlarmConfTempLineProfile,
adsl2LAlarmConfTempChan1ConfProfile,
adsl2LAlarmConfTempChan2ConfProfile,
adsl2LAlarmConfTempChan3ConfProfile,
adsl2LAlarmConfTempChan4ConfProfile,
adsl2LAlarmConfTempRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line alarm
template."
::= { adsl2Groups 15 }
adsl2LineAlarmConfProfileGroup OBJECT-GROUP
OBJECTS {
adsl2LineAlarmConfProfileAtucThresh15MinFecs,
adsl2LineAlarmConfProfileAtucThresh15MinEs,
adsl2LineAlarmConfProfileAtucThresh15MinSes,
adsl2LineAlarmConfProfileAtucThresh15MinLoss,
adsl2LineAlarmConfProfileAtucThresh15MinUas,
adsl2LineAlarmConfProfileAturThresh15MinFecs,
adsl2LineAlarmConfProfileAturThresh15MinEs,
adsl2LineAlarmConfProfileAturThresh15MinSes,
adsl2LineAlarmConfProfileAturThresh15MinLoss,
adsl2LineAlarmConfProfileAturThresh15MinUas,
adsl2LineAlarmConfProfileThresh15MinFailedFullInt,
adsl2LineAlarmConfProfileThresh15MinFailedShrtInt,
adsl2LineAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a line alarm profile."
::= { adsl2Groups 16 }
adsl2ChAlarmConfProfileGroup OBJECT-GROUP
OBJECTS {
adsl2ChAlarmConfProfileAtucThresh15MinCodingViolations,
adsl2ChAlarmConfProfileAtucThresh15MinCorrected,
adsl2ChAlarmConfProfileAturThresh15MinCodingViolations,
adsl2ChAlarmConfProfileAturThresh15MinCorrected,
adsl2ChAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"The group of objects in a channel alarm profile."
::= { adsl2Groups 17 }
adsl2PMLineCurrGroup OBJECT-GROUP
OBJECTS {
adsl2PMLCurrValidIntervals,
adsl2PMLCurrInvalidIntervals,
adsl2PMLCurr15MTimeElapsed,
adsl2PMLCurr15MFecs,
adsl2PMLCurr15MEs,
adsl2PMLCurr15MSes,
adsl2PMLCurr15MLoss,
adsl2PMLCurr15MUas,
adsl2PMLCurr1DayValidIntervals,
adsl2PMLCurr1DayInvalidIntervals,
adsl2PMLCurr1DayTimeElapsed,
adsl2PMLCurr1DayFecs,
adsl2PMLCurr1DayEs,
adsl2PMLCurr1DaySes,
adsl2PMLCurr1DayLoss,
adsl2PMLCurr1DayUas
}
STATUS current
DESCRIPTION
"The group of objects that report the line-level
counters for current PM intervals."
::= { adsl2Groups 18 }
adsl2PMLineCurrInitGroup OBJECT-GROUP
OBJECTS {
adsl2PMLCurrInit15MTimeElapsed,
adsl2PMLCurrInit15MFullInits,
adsl2PMLCurrInit15MFailedFullInits,
adsl2PMLCurrInit1DayTimeElapsed,
adsl2PMLCurrInit1DayFullInits,
adsl2PMLCurrInit1DayFailedFullInits
}
STATUS current
DESCRIPTION
"The group of objects that report the full
initialization counters for current PM intervals."
::= { adsl2Groups 19 }
adsl2PMLineCurrInitShortGroup OBJECT-GROUP
OBJECTS {
adsl2PMLCurrInit15MShortInits,
adsl2PMLCurrInit15MFailedShortInits,
adsl2PMLCurrInit1DayShortInits,
adsl2PMLCurrInit1DayFailedShortInits
}
STATUS current
DESCRIPTION
"The group of objects that report the short
initialization counters for current PM intervals."
::= { adsl2Groups 20 }
adsl2PMLineHist15MinGroup OBJECT-GROUP
OBJECTS {
adsl2PMLHist15MMonitoredTime,
adsl2PMLHist15MFecs,
adsl2PMLHist15MEs,
adsl2PMLHist15MSes,
adsl2PMLHist15MLoss,
adsl2PMLHist15MUas,
adsl2PMLHist15MValidInterval
}
STATUS current
DESCRIPTION
"The group of line-level PM counters for the previous
15-minute interval."
::= { adsl2Groups 21 }
adsl2PMLineHist1DayGroup OBJECT-GROUP
OBJECTS {
adsl2PMLHist1DMonitoredTime,
adsl2PMLHist1DFecs,
adsl2PMLHist1DEs,
adsl2PMLHist1DSes,
adsl2PMLHist1DLoss,
adsl2PMLHist1DUas,
adsl2PMLHist1DValidInterval
}
STATUS current
DESCRIPTION
"The group of line-level PM counters for the previous
24-hour interval."
::= { adsl2Groups 22 }
adsl2PMLineInitHist15MinGroup OBJECT-GROUP
OBJECTS {
adsl2PMLHistInit15MMonitoredTime,
adsl2PMLHistInit15MFullInits,
adsl2PMLHistInit15MFailedFullInits,
adsl2PMLHistInit15MValidInterval
}
STATUS current
DESCRIPTION
"The group of PM counters for the previous 15-minute
interval's full initializations."
::= { adsl2Groups 23 }
adsl2PMLineInitHist15MinShortGroup OBJECT-GROUP
OBJECTS {
adsl2PMLHistInit15MShortInits,
adsl2PMLHistInit15MFailedShortInits
}
STATUS current
DESCRIPTION
"The group of PM counters for the previous 15-minute
interval's short initializations."
::= { adsl2Groups 24 }
adsl2PMLineInitHist1DayGroup OBJECT-GROUP
OBJECTS {
adsl2PMLHistinit1DMonitoredTime,
adsl2PMLHistinit1DFullInits,
adsl2PMLHistinit1DFailedFullInits,
adsl2PMLHistinit1DValidInterval
}
STATUS current
DESCRIPTION
"The group of PM counters for the previous 24-hour
interval's full initializations."
::= { adsl2Groups 25 }
adsl2PMLineInitHist1DayShortGroup OBJECT-GROUP
OBJECTS {
adsl2PMLHistinit1DShortInits,
adsl2PMLHistinit1DFailedShortInits
}
STATUS current
DESCRIPTION
"The group of PM counters for the previous 24-hour
interval's short initializations."
::= { adsl2Groups 26 }
adsl2PMChCurrGroup OBJECT-GROUP
OBJECTS {
adsl2PMChCurrValidIntervals,
adsl2PMChCurrInvalidIntervals,
adsl2PMChCurr15MTimeElapsed,
adsl2PMChCurr15MCodingViolations,
adsl2PMChCurr15MCorrectedBlocks,
adsl2PMChCurr1DayValidIntervals,
adsl2PMChCurr1DayInvalidIntervals,
adsl2PMChCurr1DayTimeElapsed,
adsl2PMChCurr1DayCodingViolations,
adsl2PMChCurr1DayCorrectedBlocks
}
STATUS current
DESCRIPTION
"The group of objects that report the channel-level
counters for current PM intervals."
::= { adsl2Groups 27 }
adsl2PMChHist15MinGroup OBJECT-GROUP
OBJECTS {
adsl2PMChHist15MMonitoredTime,
adsl2PMChHist15MCodingViolations,
adsl2PMChHist15MCorrectedBlocks,
adsl2PMChHist15MValidInterval
}
STATUS current
DESCRIPTION
"The group of objects that report the channel-level
counters for previous 15-minute PM intervals."
::= { adsl2Groups 28 }
adsl2PMChHist1DGroup OBJECT-GROUP
OBJECTS {
adsl2PMChHist1DMonitoredTime,
adsl2PMChHist1DCodingViolations,
adsl2PMChHist1DCorrectedBlocks,
adsl2PMChHist1DValidInterval
}
STATUS current
DESCRIPTION
"The group of objects that report the channel-level
counters for previous 24-hour PM intervals."
::= { adsl2Groups 29 }
adsl2ScalarSCGroup OBJECT-GROUP
OBJECTS {
adsl2ScalarSCMaxInterfaces,
adsl2ScalarSCAvailInterfaces
}
STATUS current
DESCRIPTION
"The group of objects that report the available memory
resources for DELT processes."
::= { adsl2Groups 30 }
adsl2ThreshNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
adsl2LinePerfFECSThreshAtuc,
adsl2LinePerfFECSThreshAtur,
adsl2LinePerfESThreshAtuc,
adsl2LinePerfESThreshAtur,
adsl2LinePerfSESThreshAtuc,
adsl2LinePerfSESThreshAtur,
adsl2LinePerfLOSSThreshAtuc,
adsl2LinePerfLOSSThreshAtur,
adsl2LinePerfUASThreshAtuc,
adsl2LinePerfUASThreshAtur,
adsl2LinePerfCodingViolationsThreshAtuc,
adsl2LinePerfCodingViolationsThreshAtur,
adsl2LinePerfCorrectedThreshAtuc,
adsl2LinePerfCorrectedThreshAtur,
adsl2LinePerfFailedFullInitThresh,
adsl2LinePerfFailedShortInitThresh
}
STATUS current
DESCRIPTION
"This group supports notifications of significant conditions
associated with ADSL/ADSL2/ADSL2+ lines."
::= { adsl2Groups 31 }
adsl2StatusChangeNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS {
adsl2LineStatusChangeAtuc,
adsl2LineStatusChangeAtur
}
STATUS current
DESCRIPTION
"This group supports notifications of threshold crossing
associated with ADSL/ADSL2/ADSL2+ lines."
::= { adsl2Groups 32 }
END
Reference in New Issue View Git Blame Copy Permalink