mirror of
https://github.com/hsnodgrass/snmp_mib_archive.git
synced 2025-04-18 00:13:02 +00:00
507 lines
18 KiB
Plaintext
507 lines
18 KiB
Plaintext
--
|
|
-- Caution. This MIB is temporary and experimental.
|
|
-- In the future it will be removed from products, perhaps
|
|
-- with short notice, in favor of more standard or generic MIBs.
|
|
-- Application developers should not depend on long-term access
|
|
-- to this MIB.
|
|
|
|
CISCO-CNO-SWITCH-MIB DEFINITIONS ::= BEGIN
|
|
|
|
IMPORTS
|
|
MODULE-IDENTITY, OBJECT-TYPE,
|
|
Integer32
|
|
FROM SNMPv2-SMI
|
|
MODULE-COMPLIANCE, OBJECT-GROUP
|
|
FROM SNMPv2-CONF
|
|
DisplayString
|
|
FROM SNMPv2-TC
|
|
ciscoExperiment
|
|
FROM CISCO-SMI
|
|
ifIndex
|
|
FROM RFC1213-MIB;
|
|
|
|
ciscoCNOSwitchMIB MODULE-IDENTITY
|
|
LAST-UPDATED "9810230000Z"
|
|
ORGANIZATION "Cisco System Inc."
|
|
CONTACT-INFO
|
|
"Cisco Systems
|
|
Customer Service
|
|
|
|
Postal: 170 W Tasman Drive
|
|
San Jose, CA 95134
|
|
USA
|
|
|
|
Tel: +1 800 533-NETS
|
|
|
|
E-mail: cs-sibu@cisco.com"
|
|
DESCRIPTION
|
|
"The MIB module for the management of Cisco
|
|
Network Office (CNO) switch products."
|
|
REVISION "9810230000Z"
|
|
DESCRIPTION
|
|
"Initial version of this mib."
|
|
::= { ciscoExperiment 43 }
|
|
|
|
ciscoCNOSwitchMIBObjects OBJECT IDENTIFIER ::= { ciscoCNOSwitchMIB 1 }
|
|
|
|
cnosSysInfo OBJECT IDENTIFIER ::= { ciscoCNOSwitchMIBObjects 1 }
|
|
cnosSysConfig OBJECT IDENTIFIER ::= { ciscoCNOSwitchMIBObjects 2 }
|
|
cnosPort OBJECT IDENTIFIER ::= { ciscoCNOSwitchMIBObjects 3 }
|
|
cnosVlan OBJECT IDENTIFIER ::= { ciscoCNOSwitchMIBObjects 4 }
|
|
|
|
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
-- |
|
|
-- General System Information |
|
|
-- |
|
|
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
|
|
|
|
cnosSysInfoSerialNo OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(0..255))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Serial number of the hardware."
|
|
::= { cnosSysInfo 1 }
|
|
|
|
|
|
cnosSysInfoBoardRevision OBJECT-TYPE
|
|
SYNTAX Integer32 (0..2147483647)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Returns the revision number of the switch main board
|
|
on which the system firmware resides."
|
|
::= { cnosSysInfo 2 }
|
|
|
|
cnosSysInfoBootVersion OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(0..8))
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Returns the version number of the switch boot S/W
|
|
residing in flash. The format is 'V1.2.3'."
|
|
::= { cnosSysInfo 3 }
|
|
|
|
cnosSysInfoAddrCapacity OBJECT-TYPE
|
|
SYNTAX Integer32 (0..2147483647)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The system-wide maximum number of addresses
|
|
supported."
|
|
::= { cnosSysInfo 4 }
|
|
|
|
-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
-- |
|
|
-- General System Configurations |
|
|
-- |
|
|
-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
|
|
|
|
cnosSysConfigReset OBJECT-TYPE
|
|
SYNTAX INTEGER { noReset(1), reset(2) }
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Setting this object to reset(2) causes a complete
|
|
reset of both hardware and software, but does not run
|
|
the POST (Power On Self Test).
|
|
|
|
Setting this object to noReset(1) has no effect.
|
|
The switch always returns the value noReset(1) when
|
|
this object is read."
|
|
DEFVAL { noReset }
|
|
::= { cnosSysConfig 1 }
|
|
|
|
cnosSysConfigDefaultReset OBJECT-TYPE
|
|
SYNTAX INTEGER { noReset(1), reset(2) }
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Setting this object to reset(2) causes a complete
|
|
reset of both hardware and software, but does not run
|
|
the POST (Power On Self Test). All configuration
|
|
parameters will revert to their factory default
|
|
settings, and all addresses assigned will be removed.
|
|
|
|
Setting this object to noReset(1) has no effect.
|
|
The switch always returns the value noReset(1) when
|
|
this object is read."
|
|
DEFVAL { noReset }
|
|
::= { cnosSysConfig 2 }
|
|
|
|
cnosSysConfigMonitor OBJECT-TYPE
|
|
SYNTAX INTEGER { enabled(1), disabled(2) }
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Selects whether frames to/from certain ports are
|
|
sent to conSwitchSysConfigMonitorPort. A port is
|
|
selected for monitoring purpose when its
|
|
cnosPortMonitoring object is set to enabled."
|
|
DEFVAL { disabled }
|
|
::= { cnosSysConfig 3 }
|
|
|
|
cnosSysConfigMonitorPort OBJECT-TYPE
|
|
SYNTAX Integer32 (0..8)
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Port number to which all frames to/from monitored
|
|
ports are sent. Frames are only monitored if the
|
|
sysConfigMonitor object is set to enabled(1).
|
|
|
|
A number from 1 to 8 selects a switch port. The
|
|
number 0 selects no monitor port."
|
|
DEFVAL { 0 }
|
|
::= { cnosSysConfig 4 }
|
|
|
|
-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
-- |
|
|
-- The Switch Port Table |
|
|
-- |
|
|
-- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
|
|
|
|
cnosPortTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CnosPortEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A list of configuration entries for individually
|
|
switched ports. There in one entry created
|
|
automatically for each switch port (ifType of
|
|
ethernetCsmacd) on the device."
|
|
::= { cnosPort 1 }
|
|
|
|
cnosPortEntry OBJECT-TYPE
|
|
SYNTAX CnosPortEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Configuration parameters for an individually
|
|
switched port."
|
|
INDEX { ifIndex }
|
|
::= { cnosPortTable 1 }
|
|
|
|
CnosPortEntry ::=
|
|
SEQUENCE {
|
|
cnosPortControllerRevision
|
|
Integer32,
|
|
cnosPortName
|
|
DisplayString,
|
|
cnosPortDuplexAdmin
|
|
INTEGER,
|
|
cnosPortDuplexStatus
|
|
INTEGER,
|
|
cnosPortSpeedAdmin
|
|
INTEGER,
|
|
cnosPortSpeedStatus
|
|
INTEGER,
|
|
cnosPortMonitoring
|
|
INTEGER,
|
|
cnosPortLinkStatus
|
|
INTEGER,
|
|
cnosPortSTPPortFastMode
|
|
INTEGER,
|
|
cnosPortVlanMember
|
|
INTEGER
|
|
}
|
|
|
|
cnosPortControllerRevision OBJECT-TYPE
|
|
SYNTAX Integer32 (0..2147483647)
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Returns the revision number of the port controller."
|
|
::= { cnosPortEntry 1 }
|
|
|
|
cnosPortName OBJECT-TYPE
|
|
SYNTAX DisplayString (SIZE(0..80))
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A descriptive string of up to 80 characters used by
|
|
the network administrator to name a port."
|
|
::= { cnosPortEntry 2 }
|
|
|
|
cnosPortDuplexAdmin OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
fullDuplex(1),
|
|
halfDuplex(2),
|
|
autoNegotiate(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Set to fullDuplex(1) to operate in full duplex mode:
|
|
port will allow simultaneous transmit and receive
|
|
which can double its bandwidth. Set to halfDuplex(2)
|
|
to operate in normal mode. Set to autoNegotiate(3) to
|
|
allow the switch to negotiate with the other end of
|
|
the connection."
|
|
DEFVAL { autoNegotiate }
|
|
::= { cnosPortEntry 3 }
|
|
|
|
cnosPortDuplexStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
fullDuplex(1),
|
|
halfDuplex(2)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The operating duplex mode of the switched port."
|
|
::= { cnosPortEntry 4 }
|
|
|
|
cnosPortSpeedAdmin OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
tenMbps(1),
|
|
oneHundredMbps(2),
|
|
autoNegotiate(3)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Set to tenMbps(1) to operate in 10Mbps speed mode.
|
|
Set to oneHundredMbps(2) to operate in 100Mbps speed
|
|
mode. Set to autoNegotiate(3) to allow the switch
|
|
to negotiate with the other end of the connection."
|
|
DEFVAL { autoNegotiate }
|
|
::= { cnosPortEntry 5 }
|
|
|
|
cnosPortSpeedStatus OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
tenMbps(1),
|
|
oneHundredMbps(2)
|
|
}
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The operating speed of the switched port."
|
|
::= { cnosPortEntry 6 }
|
|
|
|
cnosPortMonitoring OBJECT-TYPE
|
|
SYNTAX INTEGER { enabled(1), disabled(2) }
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Set to enabled(1) to forward receive and transmit
|
|
frames on this port to the port identified by
|
|
cnosSysConfigMonitorPort. Set to disabled(2)
|
|
to not monitor frame traffic on this port."
|
|
DEFVAL { disabled }
|
|
::= { cnosPortEntry 7 }
|
|
|
|
cnosPortLinkStatus OBJECT-TYPE
|
|
SYNTAX INTEGER { link(1), noLink(2) }
|
|
MAX-ACCESS read-only
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The current port link status."
|
|
::= { cnosPortEntry 8 }
|
|
|
|
cnosPortSTPPortFastMode OBJECT-TYPE
|
|
SYNTAX INTEGER { enabled(1), disabled(2) }
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"This object configures the port into the Spanning
|
|
Tree port-fast mode. When enabled(1), the STP can
|
|
transition the port's state directly from blocking
|
|
to forwarding, and vice versa, without going through
|
|
the intermediate listening and learning states.
|
|
|
|
This object should only be enabled for a port that
|
|
is connected to a single workstation. A port that is
|
|
attached to a network segment with multiple network
|
|
nodes or bridges should have this object set to
|
|
disabled(2) since a temporary loop may occur when
|
|
port changes state."
|
|
DEFVAL { disabled }
|
|
::= { cnosPortEntry 9 }
|
|
|
|
cnosPortVlanMember OBJECT-TYPE
|
|
SYNTAX INTEGER {
|
|
vlan1(1),
|
|
vlan2(2),
|
|
vlan3(3),
|
|
vlan4(4),
|
|
all(5)
|
|
}
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Set the port to be a member of a specified VLAN.
|
|
Set the port to all(5) to be shared among
|
|
all VLANs."
|
|
DEFVAL { vlan1 }
|
|
::= { cnosPortEntry 10 }
|
|
|
|
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
-- |
|
|
-- The VLAN Group |
|
|
-- |
|
|
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
|
|
cnosVlanTable OBJECT-TYPE
|
|
SYNTAX SEQUENCE OF CnosVlanEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Table containing a list of VLANs."
|
|
|
|
::= { cnosVlan 1 }
|
|
|
|
cnosVlanEntry OBJECT-TYPE
|
|
SYNTAX CnosVlanEntry
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Information pertaining to a VLAN."
|
|
INDEX { cnosVlanIndex }
|
|
::= { cnosVlanTable 1 }
|
|
|
|
CnosVlanEntry ::= SEQUENCE {
|
|
cnosVlanIndex
|
|
Integer32,
|
|
cnosVlanSTPState
|
|
INTEGER
|
|
}
|
|
|
|
cnosVlanIndex OBJECT-TYPE
|
|
SYNTAX Integer32(1..4)
|
|
MAX-ACCESS not-accessible
|
|
STATUS current
|
|
DESCRIPTION
|
|
"Identification of a VLAN entry."
|
|
::= { cnosVlanEntry 1 }
|
|
|
|
cnosVlanSTPState OBJECT-TYPE
|
|
SYNTAX INTEGER { enabled(1), disabled(2) }
|
|
MAX-ACCESS read-write
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The switch implements the 802.1d Spanning Tree
|
|
Algorithm & Protocol (STP) on all its port to detect
|
|
loops in the bridge topology. The user may, for
|
|
any reason, elect to disable the execution of STP,
|
|
by setting this object to disabled(2)."
|
|
DEFVAL { enabled }
|
|
::= { cnosVlanEntry 2 }
|
|
|
|
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
-- |
|
|
-- The CNO Ethernet Switch Enterprise Specific Traps |
|
|
-- |
|
|
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
|
|
ciscoCNOSwitchNotifications OBJECT IDENTIFIER
|
|
::= { ciscoCNOSwitchMIB 2 }
|
|
|
|
ciscoCNOSwitchNotificationsPrefix OBJECT IDENTIFIER
|
|
::= { ciscoCNOSwitchNotifications 0}
|
|
|
|
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
-- |
|
|
-- The CNO Ethernet Switch Enterprise Module comformance |
|
|
-- |
|
|
-- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
|
|
|
|
ciscoCNOSwitchMIBComformance OBJECT IDENTIFIER
|
|
::= { ciscoCNOSwitchMIB 3 }
|
|
|
|
ciscoCNOSwitchMIBCompliances OBJECT IDENTIFIER
|
|
::= { ciscoCNOSwitchMIBComformance 1 }
|
|
ciscoCNOSwitchMIBGroups OBJECT IDENTIFIER
|
|
::= { ciscoCNOSwitchMIBComformance 2 }
|
|
|
|
--
|
|
-- compliance statements
|
|
--
|
|
ciscoCNOSwitchCompliance MODULE-COMPLIANCE
|
|
STATUS current
|
|
DESCRIPTION
|
|
"The compliance statement for the Cisco CNO
|
|
switch products."
|
|
MODULE -- this module
|
|
MANDATORY-GROUPS {
|
|
ciscoCNOSwitchSysInfoGroup,
|
|
ciscoCNOSwitchConfigGroup,
|
|
ciscoCNOSwitchPortGroup,
|
|
ciscoCNOSwitchMonitorPortGroup,
|
|
ciscoCNOSwitchVlanGroup
|
|
}
|
|
|
|
::= { ciscoCNOSwitchMIBCompliances 1 }
|
|
|
|
--
|
|
-- group statements
|
|
--
|
|
ciscoCNOSwitchSysInfoGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cnosSysInfoSerialNo,
|
|
cnosSysInfoBoardRevision,
|
|
cnosSysInfoBootVersion,
|
|
cnosSysInfoAddrCapacity
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of the system information objects
|
|
for use with the Cisco CNO switch products."
|
|
::= { ciscoCNOSwitchMIBGroups 1 }
|
|
|
|
ciscoCNOSwitchConfigGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cnosSysConfigReset,
|
|
cnosSysConfigDefaultReset
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of the system configuration objects
|
|
for use with the Cisco CNO switch products."
|
|
::= { ciscoCNOSwitchMIBGroups 2 }
|
|
|
|
ciscoCNOSwitchPortGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cnosPortName,
|
|
cnosPortControllerRevision,
|
|
cnosPortDuplexAdmin,
|
|
cnosPortDuplexStatus,
|
|
cnosPortSpeedAdmin,
|
|
cnosPortSpeedStatus,
|
|
cnosPortLinkStatus,
|
|
cnosPortSTPPortFastMode
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of the the switched port objects for
|
|
use with the Cisco CNO switch products."
|
|
::= { ciscoCNOSwitchMIBGroups 3 }
|
|
|
|
ciscoCNOSwitchMonitorPortGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cnosSysConfigMonitor,
|
|
cnosSysConfigMonitorPort,
|
|
cnosPortMonitoring
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of the switched port monitoring objects
|
|
for use with the Cisco CNO switch products."
|
|
::= { ciscoCNOSwitchMIBGroups 4 }
|
|
|
|
ciscoCNOSwitchVlanGroup OBJECT-GROUP
|
|
OBJECTS {
|
|
cnosPortVlanMember,
|
|
cnosVlanSTPState
|
|
}
|
|
STATUS current
|
|
DESCRIPTION
|
|
"A collection of the VLAN objects for use with the
|
|
Cisco CNO switch products."
|
|
::= { ciscoCNOSwitchMIBGroups 5 }
|
|
|
|
END
|