MrMeeb/snmp_mib_archive
1
0
Fork 0
mirror of https://github.com/hsnodgrass/snmp_mib_archive.git synced 2025-04-18 00:13:02 +00:00
Code Issues Actions Packages Projects Releases Wiki Activity
snmp_mib_archive/CISCO-MGX82XX-DSX3-MIB.my 2
Heston Snodgrass 89bf4b016e initial commit
2016-12-15 15:03:18 -07:00

3661 lines
123 KiB
Plaintext
Raw Blame History

-- *****************************************************************
-- CISCO-MGX82XX-DSX3-MIB: DS3/E3 interface MIB for MGX82xx products.
--
-- January 2003, Jyotsna Gummaraju
-- December 2002, Subra Hegde
--
-- Copyright (c) 2002 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************
CISCO-MGX82XX-DSX3-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Counter32,
Integer32 FROM SNMPv2-SMI
MODULE-COMPLIANCE,
OBJECT-GROUP FROM SNMPv2-CONF
DisplayString FROM SNMPv2-TC
dsx3Line,dsx3Framing FROM BASIS-MIB
ciscoWan FROM CISCOWAN-SMI;
ciscoMgx82xxDsx3MIB MODULE-IDENTITY
LAST-UPDATED "200301110000Z"
ORGANIZATION "Cisco Systems, Inc."
CONTACT-INFO
" Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-wanatm@cisco.com"
DESCRIPTION
"The MIB Module for DS3/E3 interface
configuration , statistics and Alarm
configuration.
This MIB is supported in T3/E3 service modules
in MGX products.
Some of the T3/E3 service modules(Cards) are:
PXM1 : Processor Switch Module.
CESM-T3E3: Circuit Emulation Service Module
FRSM-VHS : Frame Relay Service Module. Includes
T3 and Channelized T3 categories.
FRSM-2CT3: Channelized FRSM Module
SRM-3T3 : Service Resource Module
Terminologies Used :
SDH : SONET Digital Hierarchy
PLCP : Physical Layer Convergence Procedure.
BERT : Bit Error Rate Testing.
FEAC : Far End Alarm Code.
OOF : Out Of Frame.
AIS : Alarm Indication Signal.
LOF : Loss Of Frame.
RAI : Remote Alarm Indication.
HCS : Header Check Sequence
HEC : Header Error Control
MA byte : Maintenance and Adaptation byte
Tx MA Byte: This is explained in ITU-T G.832
This Byte contains following fields:
Payload type
Payload dependent bits
Timing maker bit
Rx MA Byte: This is explained in ITU-T G.832
This Byte contains following fields:
Payload type
Timing maker bit
"
REVISION "200301110000Z"
DESCRIPTION
"Initial version of the MIB.
The content of this MIB was originally available
in CISCO-WAN-AXIPOP-MIB defined using SMIv1.
The applicable objects from CISCO-WAN-AXIPOP-MIB
are defined using SMIv2 in this MIB. Also the
descriptions of some of the objects have been
modified."
::= { ciscoWan 59 }
dsx3Config OBJECT IDENTIFIER ::= { dsx3Line 1 }
dsx3AlarmConfig OBJECT IDENTIFIER ::= { dsx3Line 2 }
dsx3Alarm OBJECT IDENTIFIER ::= { dsx3Line 3 }
dsx3Counter OBJECT IDENTIFIER ::= { dsx3Line 4 }
dsx3PlcpConfig OBJECT IDENTIFIER ::= { dsx3Framing 1 }
dsx3PlcpAlarmConfig OBJECT IDENTIFIER ::= { dsx3Framing 2 }
dsx3PlcpAlarm OBJECT IDENTIFIER ::= { dsx3Framing 3 }
dsx3PlcpCounter OBJECT IDENTIFIER ::= { dsx3Framing 4 }
-- --------------------------------------------------------------
--
-- dsx3Config group
-- This group contains dsx3 line configuration table
--
-- --------------------------------------------------------------
cwDsx3ConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF CwDsx3ConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The DS3/E3 Configuration table. There is one row for each
DSX3 port in the system. The table size (number of
rows) is given by the value of dsx3LineNumOfValidEntries."
::= { dsx3Config 1 }
cwDsx3ConfigEntry OBJECT-TYPE
SYNTAX CwDsx3ConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the DSX3 Configuration table."
INDEX { dsx3LineNum }
::= { cwDsx3ConfigTable 1 }
CwDsx3ConfigEntry ::=
SEQUENCE {
dsx3LineNum Integer32,
cwDsx3LineType INTEGER,
cwDsx3LineCoding INTEGER,
cwDsx3LineLength INTEGER,
dsx3LineOOFCriteria INTEGER,
dsx3LineAIScBitsCheck INTEGER,
dsx3LineLoopbackCommand INTEGER,
dsx3LineRcvFEACValidation INTEGER,
dsx3LineXmtFEACCode INTEGER,
dsx3LineBERTEnable INTEGER,
dsx3LineBERTPattern INTEGER,
dsx3LineBERTResult INTEGER,
dsx3BERTResultClrButton INTEGER,
dsx3TrailTraceOption INTEGER,
dsx3TxTrailTrace DisplayString,
dsx3RxTrailTrace DisplayString,
dsx3TxTimingMarker INTEGER,
dsx3RxTimingMarker INTEGER,
dsx3TxPayloadType INTEGER,
dsx3RxPayloadType INTEGER,
dsx3TxTumf Integer32,
dsx3RxTumf Integer32,
dsx3LineEnable INTEGER,
dsx3FarEndLoopbkLineNum INTEGER,
dsx3LineXmtClockSrc INTEGER,
dsx3FarEndLoopbkLineStatus Integer32,
dsx3LineEqualizer INTEGER,
dsx3NearEndLoopbkLineStatus Integer32,
dsx3SubRateEnable INTEGER,
dsx3DsuSelect INTEGER,
dsx3LineRate Integer32,
dsx3LineScrambleEnable INTEGER
}
dsx3LineNum OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is the identifier of a DS3/E3
Interface on a managed device.
The range supported depends upon the type of
the card(controller card, service module).
For 1 port Card : Range is 1..1
Example : CESM-T3E3
For 2 Port Card : Range is 1..2
Example : PXM1-2T3E3.
For 3 Port Card : Range is 1..3
Example: SRM-3T3"
::= { cwDsx3ConfigEntry 1 }
cwDsx3LineType OBJECT-TYPE
SYNTAX INTEGER {
dsx3CbitParity (1),
g832-g804 (2),
dsx3M23 (3),
g751 (4),
dsx3Unframed (5),
e3Unframed (6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable indicates the variety of DS3 C-bit
or E3 application implementing this interface.
The type of interface affects the interpretation
of the usage and error statistics. The rate of DS3
is 44.736 Mbps and E3 is 34.368 Mbps.
The values, in sequence, describe:
TITLE: SPECIFICATION:
dsx3CbitParity ANSI T1.107a-1990 [9a]
g832-g804 ITU-T G.832, G.804
dsx3M23 ANSI T1.107-1988 [9]
g751 ITU-T G.751
CESM-T3 supports only ds3Unframed linetype.
CESM-E3 supports only e3Unframed linetype."
::= { cwDsx3ConfigEntry 2 }
cwDsx3LineCoding OBJECT-TYPE
SYNTAX INTEGER {
dsx3B3ZS (1),
e3HDB3 (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable describes the variety of Zero Code
Suppression used on this interface, which in turn
affects a number of its characteristics.
dsx3B3ZS and e3HDB3 refer to the use of specified
patterns of normal bits and bipolar violations
which are used to replace sequences of zero bits
of a specified length.
dsx3B3ZS(1) : Bipolar 3-Zero Substitution(B3ZS) suppression.
e3HDB3 (2) : High-Density Bipolar 3(HDB3) suppression."
::= { cwDsx3ConfigEntry 3 }
cwDsx3LineLength OBJECT-TYPE
SYNTAX INTEGER {
lessThan225(1),
moreThan225(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the length of the
DS3 Line. This object provides information
for line build out circuitry if it exists
and can use this object to adjust the
line build out."
::= { cwDsx3ConfigEntry 4 }
dsx3LineOOFCriteria OBJECT-TYPE
SYNTAX INTEGER {
fBits3Of8 (1),
fBits3Of16 (2),
notApplicable(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the out of frame decision
criteria.
OOF is declared when errors are detected in the
framing octets for four consecuitive frames.
fBits3Of8(1) : an OOF condition is declared if at
least 3 of 8 framing bits are in error.
fBits3Of16(2): an OOF is declared if 3 of 16 framing
bits are found to be in error.
notApplicable(3) : used in case where it is not
applicable. This value can not be set.
This object is not applicable when cwDsx3LineType is
set to g832-g804(2) or g751(4).
This object is not applicable for CESM-T3/E3"
::= { cwDsx3ConfigEntry 5 }
dsx3LineAIScBitsCheck OBJECT-TYPE
SYNTAX INTEGER {
checkCbits(1),
ignorebits(2),
notApplicable(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If check C-Bits options is chosen then AIS is declared
when 1010 pattern is found and C-Bits are all zero.
In the other case an AIS condition is declared when the
AIS pattern 1010... is detected irrespective of the state
of the C Bits.
This object does not apply to the E3 interface.
The value notApplicable(3) is used in case of interfaces
where this object is not applicable.
This object is not applicable for CESM-T3/E3."
::= { cwDsx3ConfigEntry 6 }
dsx3LineLoopbackCommand OBJECT-TYPE
SYNTAX INTEGER {
dsx3NoLoop(1),
dsx3RemoteLineLoop(2),
dsx3LocalLineLoop(3),
dsx3InbndLocalLoopback(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable represents the loopback configuration
of the DS3/E3 interface.
The values mean:
dsx3NoLoop
Not in the loopback state. A device that is
not capable of performing a loopback on
the interface shall always return this as
it's value.
dsx3RemoteLineLoop
Near End loops back Remote data
dsx3LocalLineLoop
Near End loops back Local data(outbound).
dsx3InboundLoopback
Near End in bound loopback Local data(inbound)."
::= { cwDsx3ConfigEntry 7 }
dsx3LineRcvFEACValidation OBJECT-TYPE
SYNTAX INTEGER{
fFEACCodes4Of5 (1),
fFEACCodes8Of10 (2),
fFEACCodesDisable (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This entry specifies the FEAC code validation criteria.
fFEACCodes4Of5(1) : a valid FEAC code is declared if
4 of 5 codes match.
fFEACCodes8Of10(2): a valid FEAC code is declared if
8 of 10 codes match.
fFEACCodesDisable(3) : Do not respond to any valid FEAC code.
This object is not applicable to E3 interface.
This object is not supported in CESM-T3/E3."
::= { cwDsx3ConfigEntry 8 }
dsx3LineXmtFEACCode OBJECT-TYPE
SYNTAX INTEGER {
dsx3SendNoCode(1),
dsx3SendLineCode(2),
dsx3SendPayloadCode(3),
dsx3SendResetCode(4),
dsx3SendDS1LoopCode(5),
dsx3SendTestPattern(6)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable indicates what bit-oriented code to transmit
over the far-end alarm and control (FEAC) channel.
The values mean:
dsx3SendNoCode
sending looped or normal data
dsx3SendLineCode
sending a request for a line loopback
dsx3SendPayloadCode
sending a request for a payload loopback
(i.e., all DS1/E1s in a DS3/E3 frame)
dsx3SendResetCode
sending a loopback deactivation request.
dsx3SendDS1LoopCode
sending a request to put part of DS1/E1 within
T3/E3 respectively into loopback.
dsx3SendTestPattern
sending a test pattern.
This object is not applicable for CESM-T3/E3"
::= { cwDsx3ConfigEntry 9 }
dsx3LineBERTEnable OBJECT-TYPE
SYNTAX INTEGER {
disabled(1),
enabled(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object enables/disables the BERT function on
an interface.
The possible values are :
disabled(1): disables port BERT functionality
enabled (2): enables port BERT functionality.
value specified in dsx3LineBERTPattern
is transmitted over the interface.
The far end may be looped back and the
test pattern verified."
::= { cwDsx3ConfigEntry 10 }
dsx3LineBERTPattern OBJECT-TYPE
SYNTAX INTEGER {
allZero(1),
allOnes(2),
alternateOneZero(3),
doubleOneZero(4),
userOneWord(5),
userTwoWords(6),
userThreeWords(7),
userFourWords(8),
pattern2p15minus1(9),
pattern2p20minus1(10),
pattern2p23minus1(11)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object defines the test bit pattern to be
used for BERT.
The possible values are :
Repetitive Patterns
allZero(1): All Zeroes(Continuous spaces). This is
repeating pattern of zeros(...000...).
The use of this pattern is to test and verify
that the ones density policing mechanism is
functioning properly. This pattern must be
used in circuits optioned for B8ZS.
allOnes(2): All Ones(Continuous Marks). This is repeating
pattern of ones(...1111...). This provides
testing of maximum power level requirements.
The all one pattern test causes the repeater
to consume the maximum amount of power.
If there is insufficient DC span power then the
repeater may begin to fail.
Typically this pattern is used for a simple
continuity check. It may also be used to detect
the presence of unwanted loop in the network.
alternateOneZero(3): Alternate one/zero pattern(..1010..). This
pattern produces a 50% ones density. It is
used to stress the repeater's DC power
consumption.
doubleOneZero(4): Double alternate one/zero(..1100..).
userOneWord(5),
userTwoWords(6),
userThreeWords(7),
userFourWords(8),
pattern2p15minus1(9) :
This is the 2^15-1(32767 bit length)
pattern as specified in ITU O.151.
It has the maximum of 15(inverted) sequential zeros.
This sequence is primarily intended for
error and jitter measurements at bit
rates of 1544, 2048, 6312, 8448,
32064 and 44736 kbit/s.
pattern2p20minus1(10):
This is the 2^20-1(1048575 bits in length)
pattern specified in ITU O.153.It has
the maximum of 19(non-inverted) sequential
zeros. This pattern is primarily intended
for error measurements at bit rates up to
73kbit/s. This pattern stresses the
equalization and timing recovery circuitry
of line repeaters.
pattern2p23minus1(11):
This is the 2^23-1(1048575 bits in length) pattern."
::= { cwDsx3ConfigEntry 11 }
dsx3LineBERTResult OBJECT-TYPE
SYNTAX INTEGER {
bertFailed(1),
bertPassed(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Result of BERT Test. The value in this object
is not applicable if dsx3LineBERTEnable is set to
disabled(1)."
::= { cwDsx3ConfigEntry 12 }
dsx3BERTResultClrButton OBJECT-TYPE
SYNTAX INTEGER {
noAction(1),
clear(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object to clear(2) causes the BERT
result field to get cleared."
::= { cwDsx3ConfigEntry 13 }
--
-- The following are the E3 specific configuration parameters
--
dsx3TrailTraceOption OBJECT-TYPE
SYNTAX INTEGER {
disable(1),
enable(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used for enabling/disabling
G.832 Trail Trace. The trail trace is used to
repetitively transmit a trail access point identifier
so that a trail receiving terminal can verify its
continued connection to the intended transmitter.
It uses a 16-byte numbering format (see Rec E.164).
The first byte of the string is a frame start marker
and includes the result of a CRC-7 calculation over
the previous frame.
The value of this object is set to disable(1) in case
of cards where this feature is not supported.
This object is not applicable for FRSM-VHS and
CESM-T3/E3."
REFERENCE
"ITU-T G.832"
::= { cwDsx3ConfigEntry 14 }
dsx3TxTrailTrace OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..15))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used for specifying the
data to be used for G.832 Trail Trace ID/String.
This object is applicable only for E3 interfaces
with G.832 framing.
The trail trace ID is a 16 octet field that
contains 1 octet of CRC-7(first octet) and 15
octets of data.
The CRC-7 is automatically calculated by the
system(card supporting this feature).
The format of the value is:
Frame Start Marker Error(HEX): CRC-7
Bytes 2-6 (ASCII) [Byte 1-5 of this object]
Bytes 7-11 (ASCII) [Byte 6-10 of this object]
Bytes 12-16 (ASCII) [Byte 11-15 of this object]
This object is not applicable for FRSM-VHS and
CESM-T3/E3."
REFERENCE
"ITU-T G.832"
::= { cwDsx3ConfigEntry 15 }
dsx3RxTrailTrace OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..15))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Received G.832 Trail Trace string.
The format of the value is:
First byte indicates CRC-7(frame start marker).
Bytes 2-6 (ASCII) [Byte 1-5 of this object]
Bytes 7-11 (ASCII) [Byte 6-10 of this object]
Bytes 12-16 (ASCII) [Byte 11-15 of this object]
The value of all zeroes indicates bad CRC-7.
This object is not applicable for FRSM-VHS and
CESM-T3/E3."
REFERENCE
"ITU-T G.832"
::= { cwDsx3ConfigEntry 16 }
dsx3TxTimingMarker OBJECT-TYPE
SYNTAX INTEGER {
traceable (1),
untraceable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Transmitted timing marker bit in G.832 MA byte.
This object can be set to traceable(1) to indicate
that the timing source is traceable to a primary
reference clock and is otherwise set to untraceable(2).
This is always set to untraceable(2) in case of
card where this feature is not supported.
This feature is not supported in FRSM-VHS and
CESM-T3/E3."
REFERENCE
"ITU-T G.832"
::= { cwDsx3ConfigEntry 17 }
dsx3RxTimingMarker OBJECT-TYPE
SYNTAX INTEGER {
traceable (1),
untraceable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Received timing marker bit in G.832 MA byte.
This object can be set to traceable(1) to indicate
that the timing source is tracable to a primary
reference clock and is otherwise set to untraceable(2).
This is always set to untraceable(2) in case of
card where this feature is not supported.
This feature is not supported in FRSM-VHS and
CESM-T3/E3."
REFERENCE
"ITU-T G.832"
::= { cwDsx3ConfigEntry 18 }
dsx3TxPayloadType OBJECT-TYPE
SYNTAX INTEGER {
unequipped (1),
equipped (2),
atm (3),
sdhtu12s (4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object specifies the G.832 payload type
for transmit data.
The possible values are :
unequipped (1): not carrying any payload
equipped (2): Equipped,non-specific
atm (3): ATM
sdhtu12s (4): SDH Elements mapping
It is recommended that this object is not instantiated
in case of cards which does not support G.832 functionality.
This is not supported in FRSM-VHS and CESM-T3/E3"
REFERENCE
"ITU-T G.832 section 2.1.2."
DEFVAL { unequipped }
::= { cwDsx3ConfigEntry 19 }
dsx3RxPayloadType OBJECT-TYPE
SYNTAX INTEGER {
unequipped (1),
equipped (2),
atm (3),
sdhtu12s (4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Received payload type field in G.832 byte
The possible values are :
unequipped (1): not carrying any payload
equipped (2): Equipped,non-specific
atm (3): ATM
sdhtu12s (4): SDH Elements mapping
It is recommended that this object is not instantiated
in case of cards which does not support G.832 functionality.
This is not supported in FRSM-VHS and CESM-T3/E3"
REFERENCE
"ITU-T G.832 section 2.1.2."
::= { cwDsx3ConfigEntry 20 }
dsx3TxTumf OBJECT-TYPE
SYNTAX Integer32 (0..3)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the value of
Tributary Multiframe Indicator(bits 6 and 7 of MA byte)
in case of TU-1xs mapping.
This is not supported in FRSM-VHS and CESM-T3/E3."
REFERENCE
"ITU-T G.832, section 3.4.3"
::= { cwDsx3ConfigEntry 21 }
dsx3RxTumf OBJECT-TYPE
SYNTAX Integer32 (0..3)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains the value of
Tributary Multiframe Indicator(bits 6 and 7 of MA byte)
in case of TU-1xs mapping.
This object is not supported in FRSM-VHS
and CESM-T3/E3."
REFERENCE
"ITU-T G.832, section 3.4.3"
::= { cwDsx3ConfigEntry 22 }
dsx3LineEnable OBJECT-TYPE
SYNTAX INTEGER {
disable (1),
enable (2),
modify (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is used for enabling/disabling an interface
and modifying the interface configuration.
The possible values are:
disable (1): Interface is administratively down
enable (2): Interface is administratively up.
modify (3): Used for modifying the parameters
of an interface that has been already
enabled(administratively up).
To modify the parameters of this table, the value
of this object must be set to enable(2) or modify(3)."
::= { cwDsx3ConfigEntry 23 }
dsx3FarEndLoopbkLineNum OBJECT-TYPE
SYNTAX INTEGER {
ds1line1(1),
ds1line2(2),
ds1line3(3),
ds1line4(4),
ds1line5(5),
ds1line6(6),
ds1line7(7),
ds1line8(8),
ds1line9(9),
ds1line10(10),
ds1line11(11),
ds1line12(12),
ds1line13(13),
ds1line14(14),
ds1line15(15),
ds1line16(16),
ds1line17(17),
ds1line18(18),
ds1line19(19),
ds1line20(20),
ds1line21(21),
ds1line22(22),
ds1line23(23),
ds1line24(24),
ds1line25(25),
ds1line26(26),
ds1line27(27),
ds1line28(28),
ds1line29(29),
ds3line(30)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specify which DS1 or DS3 line in the far-end for the
loopback testing.
For CESM-T3/E3, only ds3line(30) is valid."
::= { cwDsx3ConfigEntry 24 }
dsx3LineXmtClockSrc OBJECT-TYPE
SYNTAX INTEGER {
backplaneClk (1),
recoverClk (2),
localClk (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The source of the transmit clock.
backplaneClk(2) : clock source is from the backplane.
recoverClk (3) : clock source is derived from another
t3 interface.
localClk (4) : clock source is from a local
oscillator on the card"
::= { cwDsx3ConfigEntry 25 }
dsx3FarEndLoopbkLineStatus OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is a bitmap of the DSX3 FarEnd line
loopback status bits
Bit Position Loopback indicator
----------- -----
1 DS1 Line 1
2 DS1 Line 2
3 DS1 Line 3
4 DS1 Line 4
5 DS1 Line 5
6 DS1 Line 6
7 DS1 Line 7
8 DS1 Line 8
9 DS1 Line 9
10 DS1 Line 10
11 DS1 Line 11
12 DS1 Line 12
...
...
...
28 DS1 Line 28
29 all DS1 Lines
30 DSX3
For CESM-T3/E3, only DSX3 bit (bit 30) is valid."
::= { cwDsx3ConfigEntry 26 }
dsx3LineEqualizer OBJECT-TYPE
SYNTAX INTEGER {
intrnlequalizer(1),
extequalizer(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object indicates whether the internal equalizer
is being used or bypassed. Set this value depending on
the line equipment to which the receiver is attached.
intrnlequalizer(1): Use internal line equalizer
extequalizer(2) : Use External equalizer or bypass internal
equalizer."
::= { cwDsx3ConfigEntry 27 }
dsx3NearEndLoopbkLineStatus OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is a bitmap of the DSX3 NearEnd line
loopback status bits
BitPosition Loopback indicator
----------- -----
1 DS1 Line 1
2 DS1 Line 2
3 DS1 Line 3
4 DS1 Line 4
5 DS1 Line 5
6 DS1 Line 6
7 DS1 Line 7
8 DS1 Line 8
9 DS1 Line 9
10 DS1 Line 10
11 DS1 Line 11
12 DS1 Line 12
...
...
...
28 DS1 Line 28
29 DS1 Line 29
30 DSX3
For CESM-T3/E3, only DSX3 bit (bit 30) is valid."
::= { cwDsx3ConfigEntry 28 }
dsx3SubRateEnable OBJECT-TYPE
SYNTAX INTEGER {
disable (1),
enable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable controls whether the DS3 subrates are
enabled or not. The DS3 subrate is part of
DSU functionality.
This object is currently supported only in FRSM-VHS
cards.
It is recommended that this object is not instantiated
in case of cards which does not support DSU functionality."
DEFVAL { disable }
::= { cwDsx3ConfigEntry 29 }
dsx3DsuSelect OBJECT-TYPE
SYNTAX INTEGER {
dl3100Mode(1),
adcKentroxMode(2),
larsCom(3),
clearChannel(4),
dsuAlgorithm2(5),
dsuAlgorithm3(6),
dsuAlgorithm4(7),
dsuAlgorithm5(8)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The dsx3DsuSelect variable controls the type of DSU mode
to be selected. The 'dsx3SubRateEnable' has to be set to
'enable' before selecting the mode in 'dsx3DsuSelect'.
The possible values for this are :
dl3100Mode - Indicates compatibility with Digital Link Inc's
DL3100 DSU mode of operation. This mode permits
line rates to be in multiples of 300 Kbps.
adcKentroxMode - Indicates compatibility with ADC Kentrox's DSU.
This mode permits line rates to be in multiples
of 500 Kbps.
larsCom - Indicates compatability with LarsCom DSU.
clearChannel - Indicates the standard G.751 framing format
(12 overhead bits and 1524 data bits in an E3
frame).This option is supported only in FRSM-2E3.
dsuAlgorithm1 - dsuAlgorith4 - Presently this is not used in any of
the cards.
This object is supported only in FRSM-VHS cards.
It is recommended that this object is not instantiated
in case of cards which does not support DSU functionality."
DEFVAL { dl3100Mode }
::= { cwDsx3ConfigEntry 30 }
dsx3LineRate OBJECT-TYPE
SYNTAX Integer32 (300..44736)
UNITS "kbps"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The desired line rate when 'dsx3SubRateEnable' is enabled.
If dsx3DsuSelect is set to 'dl3100Mode', the line rate can
be configured in steps of 300 Kbps.
If dsx3DsuSelect is set to 'adcKentroxMode', the line rate can
be configured in steps of 500 Kbps.
This object is supported only in FRSM-VHS cards.
It is recommended that this object is not instantiated
in case of cards which does not support DSU functionality."
::= { cwDsx3ConfigEntry 31 }
dsx3LineScrambleEnable OBJECT-TYPE
SYNTAX INTEGER {
disabled (1),
enabled (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable turns the scrambling feature ON/OFF
The scrambling is a technique that enables framing
to be maintained on certain medium-speed edge and
trunk interfaces.
This object is ONLY applicable for FRSM-2T3/E3."
::= { cwDsx3ConfigEntry 32 }
dsx3LineNumOfValidEntries OBJECT-TYPE
SYNTAX Integer32(0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of DSX3 configuration entries (regardless
of their current configuration) in the cwDsx3ConfigTable."
::= { dsx3Config 2 }
-- --------------------------------------------------------------
--
-- dsx3AlarmConfig group
--
-- --------------------------------------------------------------
dsx3AlarmConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dsx3AlarmConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The DSX3 interface alarm configuration table. This table contains
the parameters associated with detecting and declaring alarms for
the interface. The parameters include severity of alarm, alarm
integration parameters and 15 minute and 24 hour thresholds.
The number of rows is given by dsx3LineNumOfValidEntries."
::= { dsx3AlarmConfig 1 }
dsx3AlarmConfigEntry OBJECT-TYPE
SYNTAX Dsx3AlarmConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the DSX3 Alarm Configuration table.
Thresholds may be configured for:
Line Code Violations (LCV),
LineErrored Seconds (LES),
Line Severely Errored Seconds (LSES),
P-bit Coding Violations (PCV),
P-bit Errored Seconds (PES),
P-bit Severely Errored Seconds(PSES),
Severely Errored Seconds (SES),
Severely Errored Framing Seconds(SEFS),
Unavailable Seconds (UAS),
C-bit coding violations (CCV),
C-bit errored seconds (CES),
C-bit errored seconds (CSES).
Once these thresholds are exceeded, minor or major alarms
are raised. Please refer to RFC2496 for descriptions of these
errors."
INDEX { dsx3LineNum }
::= { dsx3AlarmConfigTable 1 }
Dsx3AlarmConfigEntry ::=
SEQUENCE {
dsx3RedSeverity INTEGER,
dsx3RAISeverity INTEGER,
dsx3NEAlarmUpCount Integer32,
dsx3NEAlarmDownCount Integer32,
dsx3NEAlarmThreshold Integer32,
dsx3FEAlarmUpCount Integer32,
dsx3FEAlarmDownCount Integer32,
dsx3FEAlarmThreshold Integer32,
dsx3StatisticalAlarmSeverity INTEGER,
dsx3LCV15MinThreshold Integer32,
dsx3LCV24HrThreshold Integer32,
dsx3LES15MinThreshold Integer32,
dsx3LES24HrThreshold Integer32,
dsx3LSES15MinThreshold Integer32,
dsx3LSES24HrThreshold Integer32,
dsx3PCV15MinThreshold Integer32,
dsx3PCV24HrThreshold Integer32,
dsx3PES15MinThreshold Integer32,
dsx3PES24HrThreshold Integer32,
dsx3PSES15MinThreshold Integer32,
dsx3PSES24HrThreshold Integer32,
dsx3SEFS15MinThreshold Integer32,
dsx3SEFS24HrThreshold Integer32,
dsx3AISS15MinThreshold Integer32,
dsx3AISS24HrThreshold Integer32,
dsx3UAS15MinThreshold Integer32,
dsx3UAS24HrThreshold Integer32,
dsx3E3BIP8CV15MinThreshold Integer32,
dsx3E3BIP8CV24HrThreshold Integer32,
dsx3E3BIP8ES15MinThreshold Integer32,
dsx3E3BIP8ES24HrThreshold Integer32,
dsx3E3BIP8SES15MinThreshold Integer32,
dsx3E3BIP8SES24HrThreshold Integer32,
dsx3CCV15MinThreshold Integer32,
dsx3CCV24HrThreshold Integer32,
dsx3CES15MinThreshold Integer32,
dsx3CES24HrThreshold Integer32,
dsx3CSES15MinThreshold Integer32,
dsx3CSES24HrThreshold Integer32
}
dsx3RedSeverity OBJECT-TYPE
SYNTAX INTEGER {
minor(1),
major(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to setup the severity of RED
alarm. So when LOS/LOF alarm is detected the card will
send the alarm with appropriate severity status.
A major alarm will cause audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
LOF detection is not applicable for CESM-8T3/E3.
"
::= { dsx3AlarmConfigEntry 1 }
dsx3RAISeverity OBJECT-TYPE
SYNTAX INTEGER {
minor(1),
major(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to setup the severity of RAI
alarm. So when RAI alarm is detected the card will
send the alarm with appropriate severity status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
This is not applicable for CESM-T3/E3.
"
::= { dsx3AlarmConfigEntry 2 }
dsx3NEAlarmUpCount OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This parameter specifies the increment to the
Near End alarm integration counters. The local
alarms are LOS and LOF. The Default value is 6
and the integration counter is incremented by
this value every 10 ms while the alarm persists.
The counter is decremented by the value of
dsx3NEAlarmDnCount while there is no alarm
(the counter does not decrement below zero).
When the integration counter exceeds
dsx3NEAlarmThreshold an Alarm of the severity
specified for the particular NE alarm is declared.
LOF detection is not applicable for CESM-T3/E3"
::= { dsx3AlarmConfigEntry 3 }
dsx3NEAlarmDownCount OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This parameter specifies the decrement to the
Near End alarm integration counters. The local
alarms are LOS and LOF. The Default value is 1 and
the integration counter is decremented by this value
every 10 ms while no alarm persists. The counter is
incremented by the value of dsx3NEAlarmUpCount
while there is no alarm (the counter does not decrement below
zero). When the integration counter reaches zero any Alarm
previously declared is removed.
LOF detection is not applicable for CESM-T3/E3"
::= { dsx3AlarmConfigEntry 4 }
dsx3NEAlarmThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value that
the alarm integration counter must reach for an near end
Alarm to be declared. If the up count is 6, the down count
is 1 and the threshold 1500, an Alarm is integrated in
2.5 sec and removed in 15 seconds."
::= { dsx3AlarmConfigEntry 5 }
dsx3FEAlarmUpCount OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This parameter specifies the increment to the
Far End alarm integration counters. The local alarms
are RAI and AIS. The Default value is 6 and the
integration counter is incremented by this value every
10 ms while the alarm persists. The counter is decremented
by the value of dsx3FEAlarmDnCount while there is no alarm
(the counter does not decrement below zero).
When the integration counter exceeds dsx3FEAlarmThreshold
an Alarm of the severity specified for the particular far end
alarm is declared.
This object is not applicable for CESM-T3/E3. "
::= { dsx3AlarmConfigEntry 6 }
dsx3FEAlarmDownCount OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This parameter specifies the decrement to the
Far End alarm integration counters. The local alarms
are AIS and RAI. The Default value is 1. The integration
counter is decremented by this value every 10 ms
(till zero), while no alarm persists. The counter is
incremented by the value of dsx3FEAlarmUpCount
while there is no alarm. When the integration counter
decrements to zero any previously declared Alarm is removed.
This object is not applicable for CESM-T3/E3. "
::= { dsx3AlarmConfigEntry 7 }
dsx3FEAlarmThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value that
the alarm integration counter must reach for an far end
Alarm to be declared. If the up count is 6, the down count
is 1 and the threshold 1500, an Alarm is integrated in
2.5 sec and removed in 15 seconds.
This object is not applicable for CESM-T3/E3. "
::= { dsx3AlarmConfigEntry 8 }
dsx3StatisticalAlarmSeverity OBJECT-TYPE
SYNTAX INTEGER {
minor(1),
major(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to setup the severity of
any of the Statistical alarms. So when a
Statistical Counter exceeds its specified threshold
the card will send the alarm with appropriate
severity. A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED."
::= { dsx3AlarmConfigEntry 9 }
dsx3LCV15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared."
::= { dsx3AlarmConfigEntry 10 }
dsx3LCV24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval"
::= { dsx3AlarmConfigEntry 11 }
dsx3LES15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared."
::= { dsx3AlarmConfigEntry 12 }
dsx3LES24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval"
::= { dsx3AlarmConfigEntry 13 }
dsx3LSES15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared."
::= { dsx3AlarmConfigEntry 14 }
dsx3LSES24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval"
::= { dsx3AlarmConfigEntry 15 }
dsx3PCV15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not supported in CESM-T3/E3.
This object is not applicable for E3 interface."
::= { dsx3AlarmConfigEntry 16 }
dsx3PCV24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
This object is not supported in CESM-T3/E3.
This object is not applicable for E3 interface."
::= { dsx3AlarmConfigEntry 17 }
dsx3PES15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not supported in CESM-T3/E3.
This object is not applicable for E3 interface."
::= { dsx3AlarmConfigEntry 18 }
dsx3PES24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval.
This object is not supported in CESM-T3/E3
This object is not applicable for E3 interface."
::= { dsx3AlarmConfigEntry 19 }
dsx3PSES15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object does not apply to the E3 interface.
This object is not supported in CESM-T3/E3."
::= { dsx3AlarmConfigEntry 20 }
dsx3PSES24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3."
::= { dsx3AlarmConfigEntry 21 }
dsx3SEFS15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmConfigEntry 22 }
dsx3SEFS24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmConfigEntry 23 }
dsx3AISS15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmConfigEntry 24 }
dsx3AISS24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmConfigEntry 25 }
dsx3UAS15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared."
::= { dsx3AlarmConfigEntry 26 }
dsx3UAS24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared. The threshold is
checked every 15 minutes for the preceding 24 hour interval"
::= { dsx3AlarmConfigEntry 27 }
dsx3E3BIP8CV15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"G.832 BIP-8 error monitoring byte. 15 minute
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3."
::= { dsx3AlarmConfigEntry 28 }
dsx3E3BIP8CV24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"G.832 BIP-8 error monitoring byte. 24 hour
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS.
This object is not supported in CESM-T3/E3."
::= { dsx3AlarmConfigEntry 29 }
dsx3E3BIP8ES15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"G.832 BIP-8 error monitoring byte. 15 minute
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS.
This object is not supported in CESM-T3/E3."
::= { dsx3AlarmConfigEntry 30 }
dsx3E3BIP8ES24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"G.832 BIP-8 error monitoring byte. 24 hour
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3
"
::= { dsx3AlarmConfigEntry 31 }
dsx3E3BIP8SES15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"G.832 BIP-8 error monitoring byte. 15 minute
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3
"
::= { dsx3AlarmConfigEntry 32 }
dsx3E3BIP8SES24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"G.832 BIP-8 error monitoring byte. 24 hour
threshold value.
This has no significance to E3 with G.751 framing
which is used in FRSM-VHS
This object is not supported in CESM-T3/E3
"
::= { dsx3AlarmConfigEntry 33 }
dsx3CCV15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3."
::= { dsx3AlarmConfigEntry 34 }
dsx3CCV24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3."
::= { dsx3AlarmConfigEntry 35 }
dsx3CES15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3."
::= { dsx3AlarmConfigEntry 36 }
dsx3CES24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3."
::= { dsx3AlarmConfigEntry 37 }
dsx3CSES15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a 15 minute window causes
a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3."
::= { dsx3AlarmConfigEntry 38 }
dsx3CSES24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the value
which when exceeded in a sliding 24 hour window causes
a statistical alarm to be declared.
This object is not applicable for E3 interface.
This object is not supported in CESM-T3/E3."
::= { dsx3AlarmConfigEntry 39 }
-- --------------------------------------------------------------
--
-- dsx3Alarm group
-- This group contains dsx3 Alarm table
--
-- --------------------------------------------------------------
dsx3AlarmTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dsx3AlarmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The DSX3 interface alarm table. This table
contains the performance statistics and Error Events
based on 15 minute and/or 24 hour interval.
Performance Parameters:
LES : Line Errored Seconds
PES : P-bit Errored Seconds
PSES : P-bit Severely Errored Seconds
CES : C-bit Errored Seconds
CSES : C-bit Severely Errored Seconds
SEFS : Severely Errored Framing Seconds
UAS : Unavailable Seconds
Error Events:
BPV : Bipolar Violation
EXZ : Excessive Zeros
LCV : Line Coding Violation
PCV : P-bit Coding Violation
CCV : C-bit Coding Violation."
REFERENCE
"RFC 2496, Section 2.4.1 and 2.4.2"
::= { dsx3Alarm 1 }
dsx3AlarmEntry OBJECT-TYPE
SYNTAX Dsx3AlarmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the DSX3 Alarm table. The bucket
statistics(15 minute and 24 hour interval statistics)
are gathered for each ds3/e3 interface.
Any entry is created automatically when ds3 interface
is created."
INDEX { dsx3LineNum }
::= { dsx3AlarmTable 1 }
Dsx3AlarmEntry ::=
SEQUENCE {
dsx3LineAlarmState Integer32,
dsx3LineStatisticalAlarmState Integer32,
dsx3LCVCurrent Counter32,
dsx3LCV15MinBucket Counter32,
dsx3LCV24HrBucket Counter32,
dsx3LESCurrent Counter32,
dsx3LES15MinBucket Counter32,
dsx3LES24HrBucket Counter32,
dsx3LSESCurrent Counter32,
dsx3LSES15MinBucket Counter32,
dsx3LSES24HrBucket Counter32,
dsx3PCVCurrent Counter32,
dsx3PCV15MinBucket Counter32,
dsx3PCV24HrBucket Counter32,
dsx3PESCurrent Counter32,
dsx3PES15MinBucket Counter32,
dsx3PES24HrBucket Counter32,
dsx3PSESCurrent Counter32,
dsx3PSES15MinBucket Counter32,
dsx3PSES24HrBucket Counter32,
dsx3SEFSCurrent Counter32,
dsx3SEFS15MinBucket Counter32,
dsx3SEFS24HrBucket Counter32,
dsx3AISSCurrent Counter32,
dsx3AISS15MinBucket Counter32,
dsx3AISS24HrBucket Counter32,
dsx3UASCurrent Counter32,
dsx3UAS15MinBucket Counter32,
dsx3UAS24HrBucket Counter32,
dsx3PercentLcvEFS Integer32,
dsx3E3BIP8CVCurrent Counter32,
dsx3E3BIP8CV15MinBucket Counter32,
dsx3E3BIP8CV24HrBucket Counter32,
dsx3E3BIP8ESCurrent Counter32,
dsx3E3BIP8ES15MinBucket Counter32,
dsx3E3BIP8ES24HrBucket Counter32,
dsx3E3BIP8SESCurrent Counter32,
dsx3E3BIP8SES15MinBucket Counter32,
dsx3E3BIP8SES24HrBucket Counter32,
dsx3LineAlarmClrButton INTEGER,
dsx3CCVCurrent Counter32,
dsx3CCV15MinBucket Counter32,
dsx3CCV24HrBucket Counter32,
dsx3CESCurrent Counter32,
dsx3CES15MinBucket Counter32,
dsx3CES24HrBucket Counter32,
dsx3CSESCurrent Counter32,
dsx3CSES15MinBucket Counter32,
dsx3CSES24HrBucket Counter32
}
dsx3LineAlarmState OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable is a bitmap of the DSX3 Line ALarms
on the card. A value of zero indicates no alarms.
Itemized below are the individual bits:
BitPosition Alarm
----------- -----
0 Receiving RAI
1 Transmitting RAI
2 Receiving AIS
3 Transmitting AIS
4 Receiving OOF
5 Receiving LOS
6 Near End Local Loopback in effect
7 Near End Remote Loopback in effect
8 Receiving test pattern
9 Receive LCD
10 Receiving C-bit Parity pattern
"
DEFVAL {0}
::= { dsx3AlarmEntry 1 }
dsx3LineStatisticalAlarmState OBJECT-TYPE
SYNTAX Integer32(0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is a bitmap of the DSX3 Line Statistical
Alarms on the card. Zero indicates no alarms.
Itemized below are the individual alarm bits:
BitPosition Alarm
----------- -----
0 LCV 15 minute threshold exceeded
1 LCV 24 hour threshold exceeded
2 LES 15 minute threshold exceeded
3 LES 24 hour threshold exceeded
4 LSES 15 minute threshold exceeded
5 LSES 24 hour threshold exceeded
6 PCV 15 minute threshold exceeded
7 PCV 24 hour threshold exceeded
8 PES 15 minute threshold exceeded
9 PES 24 hour threshold exceeded
10 PSES 15 minute threshold exceeded
11 PSES 24 hour threshold exceeded
12 SEFS 15 minute threshold exceeded
13 SEFS 24 hour threshold exceeded
14 AISS 15 minute threshold exceeded
15 AISS 24 hour threshold exceeded
16 UAS 15 minute threshold exceeded
17 UAS 24 hour threshold exceeded
18 BIP8CV/G.832 15 minute threshold exceeded
19 BIP8CV/G.832 24 hour threshold exceeded
20 BIP8ES/G.832 15 minute threshold exceeded
21 BIP8ES/G.832 24 hour threshold exceeded
22 BIP8SES/G.832 15 minute threshold exceeded
23 BIP8SES/G.832 24 hour threshold exceeded
24 CCV 15 minute threshold exceeded
25 CCV 24 hour threshold exceeded
26 CES 15 minute threshold exceeded
27 CES 24 hour threshold exceeded
28 CSES 15 minute threshold exceeded
29 CSES 24 hour threshold exceeded
Bits 18 to 23 do not have any significance if the framing is
G.751(which is used in FRSM_VHS)
only bits 0,1,2,3,4,5,16 and 17 are applicable to CESM-T3/E3.
"
DEFVAL { 0 }
::= { dsx3AlarmEntry 2 }
dsx3LCVCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Line Code Violations(LCV)
encountered by the interface in current
15 minute period."
::= { dsx3AlarmEntry 3 }
dsx3LCV15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Line Code Violations(LCV)
encountered by the interface in current
last 15 minute period."
::= { dsx3AlarmEntry 4 }
dsx3LCV24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Line Code Violations(LCV)
encountered by the interface in current
last 24 hour period."
::= { dsx3AlarmEntry 5 }
dsx3LESCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Line Errored Seconds(LES)
encountered by the interface in current
15 minute period."
::= { dsx3AlarmEntry 6 }
dsx3LES15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Line Errored Seconds(LES)
encountered by the interface in last
15 minute period."
::= { dsx3AlarmEntry 7}
dsx3LES24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Line Errored Seconds(LES)
encountered by the interface in last
24 hour period."
::= { dsx3AlarmEntry 8 }
dsx3LSESCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Line Severely Errored Seconds(LSES)
encountered by the interface in current
15 minute period."
::= { dsx3AlarmEntry 9 }
dsx3LSES15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Line Severely Errored Seconds(LSES)
encountered by the interface in last
15 minute period."
::= { dsx3AlarmEntry 10 }
dsx3LSES24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Line Severely Errored Seconds(LSES)
encountered by the interface in last
24 hour period."
::= { dsx3AlarmEntry 11 }
dsx3PCVCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of P-bit Coding Violations(PCV)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 12 }
dsx3PCV15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of P-bit Coding Violations(PCV)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 13 }
dsx3PCV24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of P-bit Coding Violations(PCV)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 14 }
dsx3PESCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of P-bit Errored Seconds(PES)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 15 }
dsx3PES15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of P-bit Errored Seconds(PES)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 16 }
dsx3PES24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of P-bit Errored Seconds(PES)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 17 }
dsx3PSESCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in current 15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 18 }
dsx3PSES15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in last 15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 19 }
dsx3PSES24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of P-bit Severely Errored
Seconds(PSES) encountered by the interface
in last 24 Hour period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 20 }
dsx3SEFSCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in current 15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 21 }
dsx3SEFS15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in last 15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 22 }
dsx3SEFS24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Severely Errored Framing
Seconds(PSES) encountered by the interface
in last 24 Hour period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 23 }
dsx3AISSCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of AIS Severely Errored Seconds
encountered by the interface in current 15 minute
period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 24 }
dsx3AISS15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of AIS Severely Errored Seconds
encountered by the interface in last 15 minute
period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 25 }
dsx3AISS24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of AIS Severely Errored Seconds
encountered by the interface in last 24 Hour
period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 26 }
dsx3UASCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Unavailable Seconds(UAS)
encountered by the interface in current
15 minute period."
::= { dsx3AlarmEntry 27 }
dsx3UAS15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Unavailable Seconds(UAS)
encountered by the interface in last
15 minute period."
::= { dsx3AlarmEntry 28 }
dsx3UAS24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Unavailable Seconds(UAS)
encountered by the interface in last
24 Hour period."
::= { dsx3AlarmEntry 29 }
dsx3PercentLcvEFS OBJECT-TYPE
SYNTAX Integer32(0..100)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object gives the percentage of
seconds without any LCV Errors in the
total elapsed seconds."
::= { dsx3AlarmEntry 30 }
dsx3E3BIP8CVCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in current
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3"
::= { dsx3AlarmEntry 31 }
dsx3E3BIP8CV15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in last
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3"
::= { dsx3AlarmEntry 32 }
dsx3E3BIP8CV24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of G.832 BIP-8 Coding Violations
(CV) encountered by the interface in last
24 Hour period.
This object is not supported in FRSM-VHS and
CESM-T3/E3"
::= { dsx3AlarmEntry 33 }
dsx3E3BIP8ESCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in current
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3"
::= { dsx3AlarmEntry 34 }
dsx3E3BIP8ES15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in last
15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3"
::= { dsx3AlarmEntry 35 }
dsx3E3BIP8ES24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of G.832 BIP-8 Errored Seconds(ES)
encountered by the interface in last
24 Hour period.
This object is not supported in FRSM-VHS and
CESM-T3/E3"
::= { dsx3AlarmEntry 36 }
dsx3E3BIP8SESCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in current 15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3"
::= { dsx3AlarmEntry 37 }
dsx3E3BIP8SES15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in last 15 minute period.
This object is not supported in FRSM-VHS and
CESM-T3/E3"
::= { dsx3AlarmEntry 38 }
dsx3E3BIP8SES24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of G.832 BIP-8 Severely Errored Seconds(SES)
encountered by the interface in last 24 Hour period.
This object is not supported in FRSM-VHS and
CESM-T3/E3"
::= { dsx3AlarmEntry 39 }
dsx3LineAlarmClrButton OBJECT-TYPE
SYNTAX INTEGER {
noAction(1),
clear(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object to dsx3LineAlarmClear will
cause all the alarms statuses and counters to reset."
::= {dsx3AlarmEntry 40 }
dsx3CCVCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of C-bit Coding Violations(CCV)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 41 }
dsx3CCV15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of C-bit Coding Violations(CCV)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 42 }
dsx3CCV24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of C-bit Coding Violations(CCV)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 43 }
dsx3CESCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of C-bit Errored Seconds(CES)
encountered by the interface in current
15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 44 }
dsx3CES15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of C-bit Errored Seconds(CES)
encountered by the interface in last
15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 45 }
dsx3CES24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of C-bit Errored Seconds(CES)
encountered by the interface in last
24 Hour period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 46 }
dsx3CSESCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in current 15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 47 }
dsx3CSES15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in last 15 minute period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 48 }
dsx3CSES24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of C-bit Severely Errored Seconds(CSES)
encountered by the interface in last 24 Hour period.
This object is not supported in CESM-T3/E3"
::= { dsx3AlarmEntry 49 }
-- --------------------------------------------------------------
--
-- Group "dsx3Counters"
--
-- --------------------------------------------------------------
dsx3CounterTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dsx3CounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is for ds3/e3 statistics. This table
maintains the number of times the line encountered
LOS, LOF, AIS, RAI, CCV and Framing Errors(FE)
from the time it is up. Error statistics are
cleared when the line is brought up from the failure
state."
::= { dsx3Counter 1 }
dsx3CounterEntry OBJECT-TYPE
SYNTAX Dsx3CounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the table. Statistics are gathered
for each ds3/e3 interface. An entry is created
automatically for each ds3/e3 interface that
is activated."
INDEX { dsx3LineNum }
::= { dsx3CounterTable 1 }
Dsx3CounterEntry ::=
SEQUENCE {
dsx3RcvLOSCount Counter32,
dsx3RcvOOFCount Counter32,
dsx3RAICount Counter32,
dsx3CCVCount Counter32,
dsx3FECount Counter32,
dsx3AtmHECCount Counter32,
dsx3AtmHECSecCount Counter32,
dsx3AtmSEHECSecCount Counter32,
dsx3CounterClrButton INTEGER,
dsx3RcvPERRCounter Counter32,
dsx3RcvFEBECounter Counter32,
dsx3RcvEXZCounter Counter32,
dsx3LCVCount Counter32
}
dsx3RcvLOSCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the Loss of Signal was detected
with or without integrating to LOS alarm."
::= { dsx3CounterEntry 1 }
dsx3RcvOOFCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the Out of Frame was detected
with or without integrating to OOF alarm.
This object is not supported in CESM-T3/E3"
::= { dsx3CounterEntry 2 }
dsx3RAICount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times Yellow Alarms was detected with
or without integrating to RAI alarm.
This object is not supported in CESM-T3/E3"
::= { dsx3CounterEntry 3 }
dsx3CCVCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of C Bit
Coding Violations encountered by a DS3/E3 interface.
This object is not supported in CESM-T3/E3"
::= { dsx3CounterEntry 4 }
dsx3FECount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Framing Pattern Errors encountered by
a DS3/E3 interface.
This object is not supported in CESM-T3/E3"
::= { dsx3CounterEntry 5 }
dsx3AtmHECCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Header Check Sequence(HCS) Errors.
This object is not supported in CESM-T3/E3"
::= { dsx3CounterEntry 6 }
dsx3AtmHECSecCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of HEC errored seconds.
This object is not supported in CESM-T3/E3"
::= { dsx3CounterEntry 7 }
dsx3AtmSEHECSecCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Severely HEC error seconds.
This object is not supported in CESM-T3/E3"
::= { dsx3CounterEntry 8 }
dsx3CounterClrButton OBJECT-TYPE
SYNTAX INTEGER {
noAction(1),
clear (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to clear all the counters."
::= { dsx3CounterEntry 9 }
dsx3RcvPERRCounter OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of P-bit parity error.
This object is not supported in CESM-T3/E3"
::= { dsx3CounterEntry 10 }
dsx3RcvFEBECounter OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Far-end block error.
This object is not supported in CESM-T3/E3"
::= { dsx3CounterEntry 11 }
dsx3RcvEXZCounter OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of excessive zeros
This object is not supported in CESM-T3/E3"
::= { dsx3CounterEntry 12 }
dsx3LCVCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Line
Coding Violations encountered by a DS3/E3 interface."
::= { dsx3CounterEntry 13 }
-- --------------------------------------------------------------
--
-- dsx3PlcpConfig group
-- This group contains dsx3Plcp configuration table
--
-- --------------------------------------------------------------
dsx3PlcpConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dsx3PlcpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains ATM interface DS3 PLCP
configuration parameters."
::= { dsx3PlcpConfig 1 }
dsx3PlcpConfigEntry OBJECT-TYPE
SYNTAX Dsx3PlcpConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the DSX3 PLCP Configuration table."
INDEX { dsx3PlcpNum }
::= { dsx3PlcpConfigTable 1 }
Dsx3PlcpConfigEntry ::=
SEQUENCE {
dsx3PlcpNum Integer32,
dsx3PlcpCellFraming INTEGER,
dsx3PlcpPayloadScramble INTEGER,
dsx3PlcpLoopCommand INTEGER
}
dsx3PlcpNum OBJECT-TYPE
SYNTAX Integer32 (1..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies the dsx3 PLCP interface.
The value of this object must be same as the value
specified in 'dsx3LineNum' object from cwDsx3ConfigTable."
::= { dsx3PlcpConfigEntry 1 }
dsx3PlcpCellFraming OBJECT-TYPE
SYNTAX INTEGER {
framingByPlcp (1),
framingbyAtmHec (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value for this object sets the cell delineation
method used by the interface. The cell delineation
defines how a receiving device recognizes the start
and end of an ATM cell.
framingByPlcp (1): The ATM Cells are in predetermined
location within each PLCP row, so
no additional method is needed to
delineate ATM cells.
framingByAtmHec (2): The Header Error Control field of the
ATM cell header is used to delineate
ATM cells.
"
::= { dsx3PlcpConfigEntry 2 }
dsx3PlcpPayloadScramble OBJECT-TYPE
SYNTAX INTEGER {
enableScrambling (1),
disableScrambling (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value for this object is used for enabling/disabling
PLCP cell scrambling."
::= { dsx3PlcpConfigEntry 3 }
dsx3PlcpLoopCommand OBJECT-TYPE
SYNTAX INTEGER {
noLoop (1),
remoteLineLoop (2),
localLineLoop (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"specifies the type of loopback on the line.
The possible value(s) are :
noLoop (1): Not in loopback.
remoteLineLoop (2): Remote Line Loopback.
localLineLoop (3): Local Line Loopback."
::= { dsx3PlcpConfigEntry 4 }
dsx3PlcpNumOfValidEntries OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates the maximum number of
entries in cwDsx3ConfigTable."
::= { dsx3PlcpConfig 2 }
-- --------------------------------------------------------------
--
-- dsx3PlcpAlarmConfig group
--
-- --------------------------------------------------------------
dsx3PlcpAlarmConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dsx3PlcpAlarmConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains the ATM interface PLCP alarm
parameters."
::= { dsx3PlcpAlarmConfig 1 }
dsx3PlcpAlarmConfigEntry OBJECT-TYPE
SYNTAX Dsx3PlcpAlarmConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the DSX3 PLCP Alarm Configuration table.
Thresholds may be configured for:
Errored Seconds (ES)
Coding Violations (CV)
Severely Errored Seconds (SES)
Unavailable Seconds (UAS),
Once these thresholds are exceeded, minor or major alarms
are raised. Please refer to RFC2496 for descriptions of these
errors."
INDEX { dsx3PlcpNum }
::= { dsx3PlcpAlarmConfigTable 1 }
Dsx3PlcpAlarmConfigEntry ::=
SEQUENCE {
dsx3PlcpRedSeverity INTEGER,
dsx3PlcpRAISeverity INTEGER,
dsx3PlcpLssSeverity INTEGER,
dsx3PlcpLssEnable INTEGER,
dsx3PlcpLssCodeConnected Integer32,
dsx3PlcpLssCodeRxLinkDn Integer32,
dsx3PlcpLssCodeRxLinkUp Integer32,
dsx3PlcpStatisticalAlarmSeverity INTEGER,
dsx3PlcpBip8CV15MinThreshold Integer32,
dsx3PlcpBip8CV24HrThreshold Integer32,
dsx3PlcpBip8ES15MinThreshold Integer32,
dsx3PlcpBip8ES24HrThreshold Integer32,
dsx3PlcpBip8SES15MinThreshold Integer32,
dsx3PlcpBip8SES24HrThreshold Integer32,
dsx3PlcpSEFS15MinThreshold Integer32,
dsx3PlcpSEFS24HrThreshold Integer32,
dsx3PlcpUAS15MinThreshold Integer32,
dsx3PlcpUAS24HrThreshold Integer32
}
dsx3PlcpRedSeverity OBJECT-TYPE
SYNTAX INTEGER {
minor(1),
major(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to setup the severity of PLCP RED
alarm. So when PLCP_OOF alarm is detected the card will
declare the alarm with appropriate severity status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED."
::= { dsx3PlcpAlarmConfigEntry 1 }
dsx3PlcpRAISeverity OBJECT-TYPE
SYNTAX INTEGER {
minor(1),
major(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to setup the severity of
PLCP RAI alarm. So when PLCP RAI alarm is detected
the card will send the alarm with appropriate severity
status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED."
::= { dsx3PlcpAlarmConfigEntry 2 }
dsx3PlcpLssSeverity OBJECT-TYPE
SYNTAX INTEGER {
minor(1),
major(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to setup the severity of
PLCP RAI alarm. So when PLCP LSS alarm is detected
the card will send the alarm with appropriate severity
status.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED."
::= { dsx3PlcpAlarmConfigEntry 3 }
dsx3PlcpLssEnable OBJECT-TYPE
SYNTAX INTEGER {
lssEnable (1),
lssDisable (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This objects specifies whether the LSS feature is
enabled/disabled."
::= { dsx3PlcpAlarmConfigEntry 4 }
dsx3PlcpLssCodeConnected OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object derfines the value of the LSS code
that is to be interpreted as Link Connected."
::= { dsx3PlcpAlarmConfigEntry 5 }
dsx3PlcpLssCodeRxLinkDn OBJECT-TYPE
SYNTAX Integer32(0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object defines the value of the LSS code
that is to be identified as Receive Link Down."
::= { dsx3PlcpAlarmConfigEntry 6 }
dsx3PlcpLssCodeRxLinkUp OBJECT-TYPE
SYNTAX Integer32(0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object defines the value of the LSS code that
is to be interpreted as Receive Link Up."
::= { dsx3PlcpAlarmConfigEntry 7 }
dsx3PlcpStatisticalAlarmSeverity OBJECT-TYPE
SYNTAX INTEGER {
minor(1),
major(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable sets up the severity of PLCP Statistical
alarm. So when PLCP Statistical alarm is detected, the
card will send the alarm with appropriate severity.
A major alarm will cause the audible notification
and the MAJOR ALARM LED will be turned ON.
A minor alarm will just turn on the MINOR ALARM LED.
"
::= { dsx3PlcpAlarmConfigEntry 8 }
dsx3PlcpBip8CV15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared."
::= { dsx3PlcpAlarmConfigEntry 9 }
dsx3PlcpBip8CV24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval"
::= { dsx3PlcpAlarmConfigEntry 10 }
dsx3PlcpBip8ES15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared."
::= { dsx3PlcpAlarmConfigEntry 11 }
dsx3PlcpBip8ES24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval"
::= { dsx3PlcpAlarmConfigEntry 12 }
dsx3PlcpBip8SES15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared."
::= { dsx3PlcpAlarmConfigEntry 13 }
dsx3PlcpBip8SES24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval"
::= { dsx3PlcpAlarmConfigEntry 14 }
dsx3PlcpSEFS15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared."
::= { dsx3PlcpAlarmConfigEntry 15 }
dsx3PlcpSEFS24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval"
::= { dsx3PlcpAlarmConfigEntry 16 }
dsx3PlcpUAS15MinThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a 15 minute window
causes a statistical alarm to be declared."
::= { dsx3PlcpAlarmConfigEntry 17 }
dsx3PlcpUAS24HrThreshold OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value set in this object determines the
value which when exceeded in a sliding 24 hour
window causes a statistical alarm to be declared.
The threshold is checked every 15 minutes for the
preceding 24 hour interval"
::= { dsx3PlcpAlarmConfigEntry 18 }
-- --------------------------------------------------------------
--
-- dsx3PlcpAlarm group
-- This group contains dsx3 Alarm table
--
-- --------------------------------------------------------------
dsx3PlcpAlarmTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dsx3PlcpAlarmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains ATM interface DS3 PLCP
alarm configuration."
::= { dsx3PlcpAlarm 1 }
dsx3PlcpAlarmEntry OBJECT-TYPE
SYNTAX Dsx3PlcpAlarmEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the ATM DS3 PLCP alarm table.
Bucket statistics (15 minute and 24 Hour interval)
are gathered for each ds3/e3 interface automatically."
INDEX { dsx3PlcpNum }
::= { dsx3PlcpAlarmTable 1 }
Dsx3PlcpAlarmEntry ::=
SEQUENCE {
dsx3PlcpLineAlarmState Integer32,
dsx3PlcpLineStatisticalAlarmState Integer32,
dsx3PlcpBip8CVCurrent Counter32,
dsx3PlcpBip8CV15MinBucket Counter32,
dsx3PlcpBip8CV24HrBucket Counter32,
dsx3PlcpBip8ESCurrent Counter32,
dsx3PlcpBip8ES15MinBucket Counter32,
dsx3PlcpBip8ES24HrBucket Counter32,
dsx3PlcpBip8SESCurrent Counter32,
dsx3PlcpBip8SES15MinBucket Counter32,
dsx3PlcpBip8SES24HrBucket Counter32,
dsx3PlcpSEFSCurrent Counter32,
dsx3PlcpSEFS15MinBucket Counter32,
dsx3PlcpSEFS24HrBucket Counter32,
dsx3PlcpUASCurrent Counter32,
dsx3PlcpUAS15MinBucket Counter32,
dsx3PlcpUAS24HrBucket Counter32,
dsx3PlcpAlarmClrButton INTEGER
}
dsx3PlcpLineAlarmState OBJECT-TYPE
SYNTAX Integer32 (0..511)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable is a bitmap of the DSX3 Line alarms.
A value of zero indicates no alarms.
Itemized below are the individual bits:
BitPosition Alarm
----------- -----
0 Receiving RAI
1 Transmitting RAI
2 Receiving OOF
3 Receiving LSS Link Up
4 Transmitting LSS Link Up
5 Receiving LSS Link Down
6 Transmitting LSS Link Down
7 Near End Local Loopback in effect
8 Near End Remote Loopback in effect
"
::= { dsx3PlcpAlarmEntry 1 }
dsx3PlcpLineStatisticalAlarmState OBJECT-TYPE
SYNTAX Integer32(0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable is a bitmap of the DSX3 Line Statictical
Alarms on the card. A value of zero indicates no alarms.
Itemized below are the individual alarm bits:
BitPosition Alarm
----------- -----
0 Bip8CV 15 minute threshold exceeded
1 Bip8CV 24 hour threshold exceeded
2 Bip8ES 15 minute threshold exceeded
3 Bip8ES 24 hour threshold exceeded
4 Bip8SES 15 minute threshold exceeded
5 Bip8SES 24 hour threshold exceeded
6 Plcp SEFS 15 minute threshold exceeded
7 Plcp SEFS 24 hour threshold exceeded
8 Plcp UAS 15 minute threshold exceeded
9 Plcp UAS 24 hour threshold exceeded
"
::= { dsx3PlcpAlarmEntry 2 }
dsx3PlcpBip8CVCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
BIP-8 code violations encountered by the interface."
::= { dsx3PlcpAlarmEntry 3 }
dsx3PlcpBip8CV15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
BIP-8 code violations in the last 15 minute period
encountered by the interface."
::= { dsx3PlcpAlarmEntry 4 }
dsx3PlcpBip8CV24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
BIP-8 code violations in the last 24 hour period
encountered by the interface."
::= { dsx3PlcpAlarmEntry 5 }
dsx3PlcpBip8ESCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
BIP-8 code violations Errored Seconds
encountered by the interface."
::= { dsx3PlcpAlarmEntry 6 }
dsx3PlcpBip8ES15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
BIP-8 code violations Errored Seconds in the
last 15 minutes encountered by the interface."
::= { dsx3PlcpAlarmEntry 7 }
dsx3PlcpBip8ES24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
BIP-8 code violations Errored Seconds in the
last 24 hours encountered by the interface."
::= { dsx3PlcpAlarmEntry 8 }
dsx3PlcpBip8SESCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
Bip8 code violations Severely Errored Seconds
encountered by the interface."
::= { dsx3PlcpAlarmEntry 9 }
dsx3PlcpBip8SES15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
BIP-8 Severely Errored Seconds in the last
15 minutes encountered by the interface."
::= { dsx3PlcpAlarmEntry 10 }
dsx3PlcpBip8SES24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
BIP-8 Severely Errored Seconds in the last
24 hours encountered by the interface."
::= { dsx3PlcpAlarmEntry 11 }
dsx3PlcpSEFSCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
Severely Errored Framing Seconds
encountered by the interface."
::= { dsx3PlcpAlarmEntry 12 }
dsx3PlcpSEFS15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
Severely Errored Framing Seconds in the last
15 minutes encountered by the interface."
::= { dsx3PlcpAlarmEntry 13 }
dsx3PlcpSEFS24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
Severely Errored Framing Seconds in the last
24 hours encountered by the interface."
::= { dsx3PlcpAlarmEntry 14 }
dsx3PlcpUASCurrent OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
Unavailable Seconds encountered by the interface."
::= { dsx3PlcpAlarmEntry 15 }
dsx3PlcpUAS15MinBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
Unavailable Seconds in the last 15 minutes
encountered by the interface."
::= { dsx3PlcpAlarmEntry 16 }
dsx3PlcpUAS24HrBucket OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This counter counts the number of
Unavailable Seconds in the last 24 hours
encountered by the interface."
::= { dsx3PlcpAlarmEntry 17 }
dsx3PlcpAlarmClrButton OBJECT-TYPE
SYNTAX INTEGER {
dsx3PlcpAlarmNoAction (1),
dsx3PlcpAlarmClear (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to clear all the alarms."
::= { dsx3PlcpAlarmEntry 18 }
-- --------------------------------------------------------------
--
-- Group "dsx3PlcpCounters"
--
-- --------------------------------------------------------------
dsx3PlcpCounterTable OBJECT-TYPE
SYNTAX SEQUENCE OF Dsx3PlcpCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table for DS3 PLCP counter table."
::= { dsx3PlcpCounter 1 }
dsx3PlcpCounterEntry OBJECT-TYPE
SYNTAX Dsx3PlcpCounterEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the DS3 PLCP counter table."
INDEX { dsx3PlcpNum }
::= { dsx3PlcpCounterTable 1 }
Dsx3PlcpCounterEntry ::=
SEQUENCE {
dsx3PlcpRcvBip8Count Counter32,
dsx3PlcpRcvOOFCount Counter32,
dsx3PlcpRcvRAICount Counter32,
dsx3PlcpFECount Counter32,
dsx3PlcpFESecCount Counter32,
dsx3PlcpSEFESecCount Counter32,
dsx3PlcpFEBECount Counter32,
dsx3PlcpFEBESecCount Counter32,
dsx3PlcpSEFEBESecCount Counter32,
dsx3PlcpHECCount Counter32,
dsx3PlcpHECSecCount Counter32,
dsx3PlcpSEHECSecCount Counter32,
dsx3PlcpCounterClrButton INTEGER
}
dsx3PlcpRcvBip8Count OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of BIP-8 errors encountered by
the interface."
::= { dsx3PlcpCounterEntry 1 }
dsx3PlcpRcvOOFCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the Out of Frame(OOF) was detected
with or without integrating to OOF alarm."
::= { dsx3PlcpCounterEntry 2 }
dsx3PlcpRcvRAICount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times Remote Alarm Indication(RAI)
was detected with or without integrating to RAI alarm."
::= { dsx3PlcpCounterEntry 3 }
dsx3PlcpFECount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Framing Errors detected."
::= { dsx3PlcpCounterEntry 4 }
dsx3PlcpFESecCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Framing Error errored seconds."
::= { dsx3PlcpCounterEntry 5 }
dsx3PlcpSEFESecCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Severely errored Framing error seconds."
::= { dsx3PlcpCounterEntry 6 }
dsx3PlcpFEBECount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Far End Block Errors(FEBE) detected."
::= { dsx3PlcpCounterEntry 7 }
dsx3PlcpFEBESecCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of FEBE errored seconds."
::= { dsx3PlcpCounterEntry 8 }
dsx3PlcpSEFEBESecCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Severely errored FEBE seconds."
::= { dsx3PlcpCounterEntry 9 }
dsx3PlcpHECCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of HCS Errors."
::= { dsx3PlcpCounterEntry 10 }
dsx3PlcpHECSecCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of HEC errored seconds."
::= { dsx3PlcpCounterEntry 11 }
dsx3PlcpSEHECSecCount OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of Severely HEC error seconds."
::= { dsx3PlcpCounterEntry 12 }
dsx3PlcpCounterClrButton OBJECT-TYPE
SYNTAX INTEGER {
dsx3PlcpCounterNoAction (1),
dsx3PlcpCounterClear (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This variable is used to clear all the counters."
::= { dsx3PlcpCounterEntry 13 }
dsx3PlcpCounterValidEntries OBJECT-TYPE
SYNTAX Integer32 (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of entries in
the dsx3PlcpCounterTable."
::= { dsx3PlcpCounter 2 }
-- conformance information
cmDsx3MIBConformance OBJECT IDENTIFIER ::= { ciscoMgx82xxDsx3MIB 2 }
cmDsx3MIBGroups OBJECT IDENTIFIER ::=
{ cmDsx3MIBConformance 1 }
cmDsx3MIBCompliances OBJECT IDENTIFIER ::=
{ cmDsx3MIBConformance 2 }
-- compliance statements
cmDsx3Compliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for objects related
to DS3 MIB."
MODULE -- this module
MANDATORY-GROUPS {
cmDsx3GeneralGroup,
cmDsx3ConfGroup,
cmDsx3BertConfigGroup,
cmDsx3StatsGroup,
cmDsx3E3AlarmConfGenGroup,
cmDsx3AlarmStatsGenGroup,
cmDsx3PlcpConfGroup,
cmDsx3PlcpStatsGroup,
cmDsx3PlcpAlarmConfGroup,
cmDsx3PlcpAlarmGroup
}
GROUP cmDsx3E3ConfGroup
DESCRIPTION
"This group is mandatory for those cards
which support E3 interfaces."
GROUP cmDsx3AlarmConfGroup
DESCRIPTION
"This group is mandatory for those cards
which support DS3 interfaces."
GROUP cmDsx3E3AlarmConfGroup
DESCRIPTION
"This group is mandatory for those cards
which support E3 interfaces."
GROUP cmDsx3AlarmStatsGroup
DESCRIPTION
"This group is mandatory for those cards
which support DS3 interfaces."
GROUP cmDsx3E3AlarmStatsGroup
DESCRIPTION
"This group is mandatory for those cards
which support E3 interfaces."
::= { cmDsx3MIBCompliances 1 }
cmDsx3GeneralGroup OBJECT-GROUP
OBJECTS {
dsx3LineNumOfValidEntries,
dsx3PlcpNumOfValidEntries,
dsx3PlcpCounterValidEntries
}
STATUS current
DESCRIPTION
"The collection of objects which are used for
providing number of entries in dsx3 and PLCP
tables."
::= { cmDsx3MIBGroups 1 }
cmDsx3ConfGroup OBJECT-GROUP
OBJECTS {
dsx3LineNum,
cwDsx3LineType,
cwDsx3LineCoding,
cwDsx3LineLength,
dsx3LineOOFCriteria,
dsx3LineAIScBitsCheck,
dsx3LineLoopbackCommand,
dsx3LineXmtFEACCode,
dsx3LineEnable,
dsx3FarEndLoopbkLineNum,
dsx3LineXmtClockSrc,
dsx3FarEndLoopbkLineStatus,
dsx3LineEqualizer,
dsx3NearEndLoopbkLineStatus,
dsx3SubRateEnable,
dsx3DsuSelect,
dsx3LineRate,
dsx3LineScrambleEnable
}
STATUS current
DESCRIPTION
"The collection of objects which are used for
configuring DS3/E3 interfaces."
::= { cmDsx3MIBGroups 2 }
cmDsx3E3ConfGroup OBJECT-GROUP
OBJECTS {
dsx3LineRcvFEACValidation,
dsx3TrailTraceOption,
dsx3TxTrailTrace,
dsx3RxTrailTrace,
dsx3TxTimingMarker,
dsx3RxTimingMarker,
dsx3TxPayloadType,
dsx3RxPayloadType,
dsx3TxTumf,
dsx3RxTumf
}
STATUS current
DESCRIPTION
"The collection of objects which are applicable
for E3 interfaces only."
::= { cmDsx3MIBGroups 3 }
cmDsx3BertConfigGroup OBJECT-GROUP
OBJECTS {
dsx3LineBERTEnable,
dsx3LineBERTPattern,
dsx3LineBERTResult,
dsx3BERTResultClrButton
}
STATUS current
DESCRIPTION
"The collection of objects which are used for
BERT on DS3/E3 interfaces."
::= { cmDsx3MIBGroups 4 }
cmDsx3StatsGroup OBJECT-GROUP
OBJECTS {
dsx3RcvLOSCount,
dsx3RcvOOFCount,
dsx3RAICount,
dsx3CCVCount,
dsx3FECount,
dsx3AtmHECCount,
dsx3AtmHECSecCount,
dsx3AtmSEHECSecCount,
dsx3CounterClrButton,
dsx3RcvPERRCounter,
dsx3RcvFEBECounter,
dsx3RcvEXZCounter,
dsx3LCVCount
}
STATUS current
DESCRIPTION
"The collection of objects related to
DS3/E3 statistics."
::= { cmDsx3MIBGroups 5 }
cmDsx3E3AlarmConfGenGroup OBJECT-GROUP
OBJECTS {
dsx3RedSeverity,
dsx3RAISeverity,
dsx3NEAlarmUpCount,
dsx3NEAlarmDownCount,
dsx3NEAlarmThreshold,
dsx3FEAlarmUpCount,
dsx3FEAlarmDownCount,
dsx3FEAlarmThreshold,
dsx3StatisticalAlarmSeverity,
dsx3LCV15MinThreshold,
dsx3LCV24HrThreshold,
dsx3LES15MinThreshold,
dsx3LES24HrThreshold,
dsx3LSES15MinThreshold,
dsx3LSES24HrThreshold,
dsx3SEFS15MinThreshold,
dsx3SEFS24HrThreshold,
dsx3UAS15MinThreshold,
dsx3UAS24HrThreshold
}
STATUS current
DESCRIPTION
"The collection of objects used for
alarm configuration of DS3 and E3 interfaces."
::= { cmDsx3MIBGroups 6 }
cmDsx3AlarmConfGroup OBJECT-GROUP
OBJECTS {
dsx3PCV15MinThreshold,
dsx3PCV24HrThreshold,
dsx3PES15MinThreshold,
dsx3PES24HrThreshold,
dsx3PSES15MinThreshold,
dsx3PSES24HrThreshold,
dsx3AISS15MinThreshold,
dsx3AISS24HrThreshold,
dsx3CCV15MinThreshold,
dsx3CCV24HrThreshold,
dsx3CES15MinThreshold,
dsx3CES24HrThreshold,
dsx3CSES15MinThreshold,
dsx3CSES24HrThreshold
}
STATUS current
DESCRIPTION
"The collection of objects used for
alarm configuration of DS3 interfaces."
::= { cmDsx3MIBGroups 7 }
cmDsx3E3AlarmConfGroup OBJECT-GROUP
OBJECTS {
dsx3E3BIP8CV15MinThreshold,
dsx3E3BIP8CV24HrThreshold,
dsx3E3BIP8ES15MinThreshold,
dsx3E3BIP8ES24HrThreshold,
dsx3E3BIP8SES15MinThreshold,
dsx3E3BIP8SES24HrThreshold
}
STATUS current
DESCRIPTION
"The collection of objects used for
alarm configuration of E3 interfaces."
::= { cmDsx3MIBGroups 8 }
cmDsx3AlarmStatsGenGroup OBJECT-GROUP
OBJECTS {
dsx3LineAlarmState,
dsx3LineStatisticalAlarmState,
dsx3LCVCurrent,
dsx3LCV15MinBucket,
dsx3LCV24HrBucket,
dsx3LESCurrent,
dsx3LES15MinBucket,
dsx3LES24HrBucket,
dsx3LSESCurrent,
dsx3LSES15MinBucket,
dsx3LSES24HrBucket,
dsx3SEFSCurrent,
dsx3SEFS15MinBucket,
dsx3SEFS24HrBucket,
dsx3UASCurrent,
dsx3UAS15MinBucket,
dsx3UAS24HrBucket,
dsx3PercentLcvEFS,
dsx3LineAlarmClrButton
}
STATUS current
DESCRIPTION
"The collection of objects related to
performance statistics and error events
for ds3 end e3 interfaces."
::= { cmDsx3MIBGroups 9 }
cmDsx3AlarmStatsGroup OBJECT-GROUP
OBJECTS {
dsx3PCVCurrent,
dsx3PCV15MinBucket,
dsx3PCV24HrBucket,
dsx3PESCurrent,
dsx3PES15MinBucket,
dsx3PES24HrBucket,
dsx3PSESCurrent,
dsx3PSES15MinBucket,
dsx3PSES24HrBucket,
dsx3AISSCurrent,
dsx3AISS15MinBucket,
dsx3AISS24HrBucket,
dsx3CCVCurrent,
dsx3CCV15MinBucket,
dsx3CCV24HrBucket,
dsx3CESCurrent,
dsx3CES15MinBucket,
dsx3CES24HrBucket,
dsx3CSESCurrent,
dsx3CSES15MinBucket,
dsx3CSES24HrBucket
}
STATUS current
DESCRIPTION
"The collection of objects related to
performance statistics and error events
for ds3 interfaces."
::= { cmDsx3MIBGroups 10 }
cmDsx3E3AlarmStatsGroup OBJECT-GROUP
OBJECTS {
dsx3E3BIP8CVCurrent,
dsx3E3BIP8CV15MinBucket,
dsx3E3BIP8CV24HrBucket,
dsx3E3BIP8ESCurrent,
dsx3E3BIP8ES15MinBucket,
dsx3E3BIP8ES24HrBucket,
dsx3E3BIP8SESCurrent,
dsx3E3BIP8SES15MinBucket,
dsx3E3BIP8SES24HrBucket
}
STATUS current
DESCRIPTION
"The collection of objects related to
performance statistics and error events
for e3 interfaces."
::= { cmDsx3MIBGroups 11 }
cmDsx3PlcpConfGroup OBJECT-GROUP
OBJECTS {
dsx3PlcpNum,
dsx3PlcpCellFraming,
dsx3PlcpPayloadScramble,
dsx3PlcpLoopCommand
}
STATUS current
DESCRIPTION
"The collection of objects related to
PLCP Configuration on DS3 interfaces."
::= { cmDsx3MIBGroups 12 }
cmDsx3PlcpStatsGroup OBJECT-GROUP
OBJECTS {
dsx3PlcpRcvBip8Count,
dsx3PlcpRcvOOFCount,
dsx3PlcpRcvRAICount,
dsx3PlcpFECount,
dsx3PlcpFESecCount,
dsx3PlcpSEFESecCount,
dsx3PlcpFEBECount,
dsx3PlcpFEBESecCount,
dsx3PlcpSEFEBESecCount,
dsx3PlcpHECCount,
dsx3PlcpHECSecCount,
dsx3PlcpSEHECSecCount,
dsx3PlcpCounterClrButton
}
STATUS current
DESCRIPTION
"The collection of objects related to
PLCP statistics on DS3 interfaces."
::= { cmDsx3MIBGroups 13 }
cmDsx3PlcpAlarmConfGroup OBJECT-GROUP
OBJECTS {
dsx3PlcpRedSeverity,
dsx3PlcpRAISeverity,
dsx3PlcpLssSeverity,
dsx3PlcpLssEnable,
dsx3PlcpLssCodeConnected,
dsx3PlcpLssCodeRxLinkDn,
dsx3PlcpLssCodeRxLinkUp,
dsx3PlcpStatisticalAlarmSeverity,
dsx3PlcpBip8CV15MinThreshold,
dsx3PlcpBip8CV24HrThreshold,
dsx3PlcpBip8ES15MinThreshold,
dsx3PlcpBip8ES24HrThreshold,
dsx3PlcpBip8SES15MinThreshold,
dsx3PlcpBip8SES24HrThreshold,
dsx3PlcpSEFS15MinThreshold,
dsx3PlcpSEFS24HrThreshold,
dsx3PlcpUAS15MinThreshold,
dsx3PlcpUAS24HrThreshold
}
STATUS current
DESCRIPTION
"The collection of objects used for
PLCP Alarm configuration on DS3 interfaces."
::= { cmDsx3MIBGroups 14 }
cmDsx3PlcpAlarmGroup OBJECT-GROUP
OBJECTS {
dsx3PlcpLineAlarmState,
dsx3PlcpLineStatisticalAlarmState,
dsx3PlcpBip8CVCurrent,
dsx3PlcpBip8CV15MinBucket,
dsx3PlcpBip8CV24HrBucket,
dsx3PlcpBip8ESCurrent,
dsx3PlcpBip8ES15MinBucket,
dsx3PlcpBip8ES24HrBucket,
dsx3PlcpBip8SESCurrent,
dsx3PlcpBip8SES15MinBucket,
dsx3PlcpBip8SES24HrBucket,
dsx3PlcpSEFSCurrent,
dsx3PlcpSEFS15MinBucket,
dsx3PlcpSEFS24HrBucket,
dsx3PlcpUASCurrent,
dsx3PlcpUAS15MinBucket,
dsx3PlcpUAS24HrBucket,
dsx3PlcpAlarmClrButton
}
STATUS current
DESCRIPTION
"The collection of objects used for
PLCP Alarm configuration on DS3 interfaces."
::= { cmDsx3MIBGroups 15 }
END
Reference in New Issue View Git Blame Copy Permalink