-- ***************************************************************** -- -- AGENT-CAPABILITIES mib for CISCO-ATM-PVCTRAP-EXTN-MIB -- -- October 2002, Hrishikesh Kulkarni -- -- Copyright (c) 2002 by Cisco Systems, Inc. -- -- ***************************************************************** CISCO-ATM-PVCTRAP-EXTN-CAPABILITY DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY FROM SNMPv2-SMI AGENT-CAPABILITIES FROM SNMPv2-CONF ciscoAgentCapability FROM CISCO-SMI; ciscoATMPVCTRAPExtnCapability MODULE-IDENTITY LAST-UPDATED "200211060000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-atm@cisco.com" DESCRIPTION "The Agent Capabilities for CISCO-ATM-PVCTRAP-EXTN-MIB." REVISION "200211060000Z" DESCRIPTION "Initial version of the MIB Module." ::= { ciscoAgentCapability 289 } ciscoATMPVCTRAPExtnCapabilityV12R00S AGENT-CAPABILITIES PRODUCT-RELEASE "Cisco IOS 12.0S" STATUS current DESCRIPTION "CISCO-ATM-PVCTRAP-EXTN-MIB Capabilities" SUPPORTS CISCO-ATM-PVCTRAP-EXTN-MIB INCLUDES { ciscoAtmPvcTrapExtnGroup, ciscoAtmPvcTrapExtnNotifGroup1 } VARIATION catmIntfPvcOAMFailureTrap -- TRAP-TYPE -- OBJECTS { ifIndex, -- catmIntfOAMFailedPVcls, -- catmIntfCurrentOAMFailingPVcls, -- atmVclVpi, -- atmVclVci, -- catmPVclStatusTransition, -- catmPVclStatusChangeStart, -- catmPVclStatusChangeEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclLowerRangeValue, -- catmPVclHigherRangeValue, -- catmPVclRangeStatusChangeStart, -- catmPVclRangeStatusChangeEnd } DESCRIPTION "A catmIntfPvcOAMFailureTrap signifies that the loopback F5 OAM failure is detected on the PVC in the last PVC TRAP notification interval. If the set of loopback failed PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclLowerRangeValue, catmPVclHigherRangeValue, catmPVclRangeStatusChangeStart, catmPVclRangeStatusChangeEnd are used. If the set of loopback failed PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of loopback failed PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclStatusTransition, catmPVclStatusChangeStart, catmPVclStatusChangeEnd will be used. In the case where the set of loopback failed PVCs contains both successive and singled out PVCs both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 1 } VARIATION catmIntfPvcSegCCOAMFailureTrap -- TRAP-TYPE -- OBJECTS { ifIndex, -- catmIntfSegCCOAMFailedPVcls, -- catmIntfCurSegCCOAMFailingPVcls, -- atmVclVpi, -- atmVclVci, -- catmPVclSegCCStatusTransition, -- catmPVclSegCCStatusChangeStart, -- catmPVclSegCCStatusChangeEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclSegCCLowerRangeValue, -- catmPVclSegCCHigherRangeValue, -- catmPVclSegCCRangeStatusChStart, -- catmPVclSegCCRangeStatusChEnd } DESCRIPTION "A catmIntfPvcSegCCOAMFailureTrap signifies that the segment CC F5 OAM failure is detected on the PVC in the last PVC TRAP notification interval. If the set of segment CC failed PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclSegCCLowerRangeValue, catmPVclSegCCHigherRangeValue, catmPVclSegCCRangeStatusChStart, catmPVclSegCCRangeStatusChEnd are used. If the set of segment CC failed PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of segment CC failed PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclSegCCStatusTransition, catmPVclSegCCStatusChangeStart, catmPVclSegCCStatusChangeEnd will be used. In the case where the set of segment CC failed PVCs contains both successive and singled out PVCs, both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 2 } VARIATION catmIntfPvcEndCCOAMFailureTrap -- TRAP-TYPE -- OBJECTS { ifIndex, -- catmIntfEndCCOAMFailedPVcls, -- catmIntfCurEndCCOAMFailingPVcls, -- atmVclVpi, -- atmVclVci, -- catmPVclEndCCStatusTransition, -- catmPVclEndCCStatusChangeStart, -- catmPVclEndCCStatusChangeEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclEndCCLowerRangeValue, -- catmPVclEndCCHigherRangeValue, -- catmPVclEndCCRangeStatusChStart, -- catmPVclEndCCRangeStatusChEnd } DESCRIPTION "A catmIntfPvcEndCCOAMFailureTrap signifies that the End CC F5 OAM failure is detected on the PVC in the last PVC TRAP notification interval. If the set of End CC failed PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclEndCCLowerRangeValue, catmPVclEndCCHigherRangeValue, catmPVclEndCCRangeStatusChStart, catmPVclEndCCRangeStatusChEnd are used. If the set of End CC failed PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of End CC failed PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclEndCCStatusTransition, catmPVclEndCCStatusChangeStart, catmPVclEndCCStatusChangeEnd will be used. In the case where the set of End CC failed PVCs contains both successive and singled out PVCs, both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 3 } VARIATION catmIntfPvcAISRDIOAMFailureTrap -- TRAP-TYPE -- OBJECTS { ifIndex, -- catmIntfAISRDIOAMFailedPVcls, -- catmIntfCurAISRDIOAMFailingPVcls, -- atmVclVpi, -- atmVclVci, -- catmPVclAISRDIStatusTransition, -- catmPVclAISRDIStatusChangeStart, -- catmPVclAISRDIStatusChangeEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclAISRDILowerRangeValue, -- catmPVclAISRDIHigherRangeValue, -- catmPVclAISRDIRangeStatusChStart, -- catmPVclAISRDIRangeStatusChEnd } DESCRIPTION "A catmIntfPvcAISRDIOAMFailureTrap signifies that the AIS/RDI F5 OAM failure is detected on the PVC in the last PVC TRAP notification interval. If the set of AIS/RDI failed PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclAISRDILowerRangeValue, catmPVclAISRDIHigherRangeValue, catmPVclAISRDIRangeStatusChStart, catmPVclAISRDIRangeStatusChEnd are used. If the set of AIS/RDI failed PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of AIS/RDI failed PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclAISRDIStatusTransition, catmPVclAISRDIStatusChangeStart, catmPVclAISRDIStatusChangeEnd will be used. In the case where the set of AIS/RDI failed PVCs contains both successive and singled out PVCs, both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 4 } VARIATION catmIntfPvcAnyOAMFailureTrap -- TRAP-TYPE -- OBJECTS { ifIndex, -- catmIntfAnyOAMFailedPVcls, -- catmIntfCurAnyOAMFailingPVcls, -- catmIntfTypeOfOAMFailure, -- atmVclVpi, -- atmVclVci, -- catmPVclStatusTransition, -- catmPVclStatusChangeStart, -- catmPVclStatusChangeEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclLowerRangeValue, -- catmPVclHigherRangeValue, -- catmPVclRangeStatusChangeStart, -- catmPVclRangeStatusChangeEnd, -- catmPVclSegCCStatusTransition, -- catmPVclSegCCStatusChangeStart, -- catmPVclSegCCStatusChangeEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclSegCCLowerRangeValue, -- catmPVclSegCCHigherRangeValue, -- catmPVclSegCCRangeStatusChStart, -- catmPVclSegCCRangeStatusChEnd, -- catmPVclEndCCStatusTransition, -- catmPVclEndCCStatusChangeStart, -- catmPVclEndCCStatusChangeEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclEndCCLowerRangeValue, -- catmPVclEndCCHigherRangeValue, -- catmPVclEndCCRangeStatusChStart, -- catmPVclEndCCRangeStatusChEnd, -- catmPVclAISRDIStatusTransition, -- catmPVclAISRDIStatusChangeStart, -- catmPVclAISRDIStatusChangeEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclAISRDILowerRangeValue, -- catmPVclAISRDIHigherRangeValue, -- catmPVclAISRDIRangeStatusChStart, -- catmPVclAISRDIRangeStatusChEnd } DESCRIPTION "A catmIntfPvcAnyOAMFailureTrap signifies that the one or more type of F5 OAM failure is detected on the PVC in the last PVC TRAP notification interval. The type of F5 OAM failure can be Loopback F5 OAM failure, Segment CC F5 OAM failure, End CC F5 OAM failure, AIS/RDI F5 OAM failure. If the set of loopback failed PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclLowerRangeValue, catmPVclHigherRangeValue, catmPVclRangeStatusChangeStart, catmPVclRangeStatusChangeEnd are used. If the set of loopback failed PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of loopback failed PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclStatusTransition, catmPVclStatusChangeStart, catmPVclStatusChangeEnd will be used. In the case where the set of loopback failed PVCs contains both successive and singled out PVCs both sets of objects will be used. If the set of segment CC failed PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclSegCCLowerRangeValue, catmPVclSegCCHigherRangeValue, catmPVclSegCCRangeStatusChStart, catmPVclSegCCRangeStatusChEnd are used. If the set of segment CC failed PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of segment CC failed PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclSegCCStatusTransition, catmPVclSegCCStatusChangeStart, catmPVclSegCCStatusChangeEnd will be used. In the case where the set of segment CC failed PVCs contains both successive and singled out PVCs, both sets of objects will be used. If the set of End CC failed PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclEndCCLowerRangeValue, catmPVclEndCCHigherRangeValue, catmPVclEndCCRangeStatusChStart, catmPVclEndCCRangeStatusChEnd are used. If the set of End CC failed PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of End CC failed PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclEndCCStatusTransition, catmPVclEndCCStatusChangeStart, catmPVclEndCCStatusChangeEnd will be used. In the case where the set of End CC failed PVCs contains both successive and singled out PVCs, both sets of objects will be used. If the set of AIS/RDI failed PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclAISRDILowerRangeValue, catmPVclAISRDIHigherRangeValue, catmPVclAISRDIRangeStatusChStart, catmPVclAISRDIRangeStatusChEnd are used. If the set of AIS/RDI failed PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of AIS/RDI failed PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclAISRDIStatusTransition, catmPVclAISRDIStatusChangeStart, catmPVclAISRDIStatusChangeEnd will be used. In the case where the set of AIS/RDI failed PVCs contains both successive and singled out PVCs, both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 5 } VARIATION catmIntfPvcOAMRecoverTrap -- TRAP-TYPE -- OBJECTS { ifIndex, -- catmIntfOAMRcovedPVcls, -- catmIntfCurrentOAMRcovingPVcls, -- atmVclVpi, -- atmVclVci, -- catmPVclStatusUpTransition, -- catmPVclStatusUpStart, -- catmPVclStatusUpEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclUpLowerRangeValue, -- catmPVclUpHigherRangeValue, -- catmPVclRangeStatusUpStart, -- catmPVclRangeStatusUpEnd } DESCRIPTION "A catmIntfPvcOAMRecoverTrap signifies that the loopback F5 OAM recovery is detected on the PVC in the last PVC TRAP notification interval. If the set of loopback recovered PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclUpLowerRangeValue, catmPVclUpHigherRangeValue, catmPVclRangeStatusUpStart, catmPVclRangeStatusUpEnd are used. If the set of loopback recovered PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of loopback recovered PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclStatusUpTransition, catmPVclStatusUpStart, catmPVclStatusUpEnd will be used. In the case where the set of loopback recovered PVCs contains both successive and singled out PVCs both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 7 } VARIATION catmIntfPvcSegCCOAMRecoverTrap -- TRAP-TYPE -- OBJECTS { ifIndex, -- catmIntfSegCCOAMRcovedPVcls, -- catmIntfCurSegCCOAMRcovingPVcls, -- atmVclVpi, -- atmVclVci, -- catmPVclSegCCStatusUpTransition, -- catmPVclSegCCStatusUpStart, -- catmPVclSegCCStatusUpEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclSegCCUpLowerRangeValue, -- catmPVclSegCCUpHigherRangeValue, -- catmPVclSegCCRangeStatusUpStart, -- catmPVclSegCCRangeStatusUpEnd } DESCRIPTION "A catmIntfPvcSegCCOAMRecoverTrap signifies that the segment CC F5 OAM recovery is detected on the PVC in the last PVC TRAP notification interval. If the set of segment CC recovered PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclSegCCUpLowerRangeValue, catmPVclSegCCUpHigherRangeValue, catmPVclSegCCRangeStatusUpStart, catmPVclSegCCRangeStatusUpEnd are used. If the set of segment CC recovered PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of segment CC recovered PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclSegCCStatusUpTransition, catmPVclSegCCStatusUpStart, catmPVclSegCCStatusUpEnd will be used. In the case where the set of segment CC recovered PVCs contains both successive and singled out PVCs, both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 8 } VARIATION catmIntfPvcEndCCOAMRecoverTrap -- TRAP-TYPE -- OBJECTS { ifIndex, -- catmIntfEndCCOAMRcovedPVcls, -- catmIntfCurEndCCOAMRcovingPVcls, -- atmVclVpi, -- atmVclVci, -- catmPVclEndCCStatusUpTransition, -- catmPVclEndCCStatusUpStart, -- catmPVclEndCCStatusUpEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclEndCCUpLowerRangeValue, -- catmPVclEndCCUpHigherRangeValue, -- catmPVclEndCCRangeStatusUpStart, -- catmPVclEndCCRangeStatusUpEnd } DESCRIPTION "A catmIntfPvcEndCCOAMRecoverTrap signifies that the End CC F5 OAM recovery is detected on the PVC in the last PVC TRAP notification interval. If the set of End CC recovered PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclEndCCUpLowerRangeValue, catmPVclEndCCUpHigherRangeValue, catmPVclEndCCRangeStatusUpStart, catmPVclEndCCRangeStatusUpEnd are used. If the set of End CC recovered PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of End CC recovered PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclEndCCStatusUpTransition, catmPVclEndCCStatusUpStart, catmPVclEndCCStatusUpEnd will be used. In the case where the set of End CC recovered PVCs contains both successive and singled out PVCs, both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 9 } VARIATION catmIntfPvcAISRDIOAMRecoverTrap -- TRAP-TYPE -- OBJECTS { ifIndex, -- catmIntfAISRDIOAMRcovedPVcls, -- catmIntfCurAISRDIOAMRcovingPVcls, -- atmVclVpi, -- atmVclVci, -- catmPVclAISRDIStatusUpTransition, -- catmPVclAISRDIStatusUpStart, -- catmPVclAISRDIStatusUpEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclAISRDIUpLowerRangeValue, -- catmPVclAISRDIUpHigherRangeValue, -- catmPVclAISRDIRangeStatusUpStart, -- catmPVclAISRDIRangeStatusUpEnd } DESCRIPTION "A catmIntfPvcAISRDIOAMRecoverTrap signifies that the AIS/RDI F5 OAM recovery is detected on the PVC in the last PVC TRAP notification interval. If the set of AIS/RDI recovered PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclAISRDIUpLowerRangeValue, catmPVclAISRDIUpHigherRangeValue, catmPVclAISRDIRangeStatusUpStart, catmPVclAISRDIRangeStatusUpEnd are used. If the set of AIS/RDI recovered PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of AIS/RDI recovered PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclAISRDIStatusUpTransition, catmPVclAISRDIStatusUpStart, catmPVclAISRDIStatusUpEnd will be used. In the case where the set of AIS/RDI recovered PVCs contains both successive and singled out PVCs, both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 10 } VARIATION catmIntfPvcAnyOAMRecoverTrap -- TRAP-TYPE -- OBJECTS { ifIndex, -- catmIntfAnyOAMRcovedPVcls, -- catmIntfCurAnyOAMRcovingPVcls, -- catmIntfTypeOfOAMRecover, -- atmVclVpi, -- atmVclVci, -- catmPVclStatusUpTransition, -- catmPVclStatusUpStart, -- catmPVclStatusUpEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclUpLowerRangeValue, -- catmPVclUpHigherRangeValue, -- catmPVclRangeStatusUpStart, -- catmPVclRangeStatusUpEnd, -- catmPVclSegCCStatusUpTransition, -- catmPVclSegCCStatusUpStart, -- catmPVclSegCCStatusUpEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclSegCCUpLowerRangeValue, -- catmPVclSegCCUpHigherRangeValue, -- catmPVclSegCCRangeStatusUpStart, -- catmPVclSegCCRangeStatusUpEnd, -- catmPVclEndCCStatusUpTransition, -- catmPVclEndCCStatusUpStart, -- catmPVclEndCCStatusUpEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclEndCCUpLowerRangeValue, -- catmPVclEndCCUpHigherRangeValue, -- catmPVclEndCCRangeStatusUpStart, -- catmPVclEndCCRangeStatusUpEnd, -- catmPVclAISRDIStatusUpTransition, -- catmPVclAISRDIStatusUpStart, -- catmPVclAISRDIStatusUpEnd, -- catmStatusChangePVclRangeIndex, -- catmPVclAISRDIUpLowerRangeValue, -- catmPVclAISRDIUpHigherRangeValue, -- catmPVclAISRDIRangeStatusUpStart, -- catmPVclAISRDIRangeStatusUpEnd } DESCRIPTION "A catmIntfPvcAnyOAMRecoverTrap signifies that the one or more type of F5 OAM recovery is detected on the PVC in the last PVC TRAP notification interval. The type of F5 OAM recovery can be Loopback F5 OAM recovery, Segment CC F5 OAM recovery, End CC F5 OAM recovery, AIS/RDI F5 OAM recovery. If the set of loopback recovered PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclUpLowerRangeValue, catmPVclUpHigherRangeValue, catmPVclRangeStatusUpStart, catmPVclRangeStatusUpEnd are used. If the set of loopback recovered PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of loopback recovered PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclStatusUpTransition, catmPVclStatusUpStart, catmPVclStatusUpEnd will be used. In the case where the set of loopback recovered PVCs contains both successive and singled out PVCs both sets of objects will be used. If the set of segment CC recovered PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclSegCCUpLowerRangeValue, catmPVclSegCCUpHigherRangeValue, catmPVclSegCCRangeStatusUpStart, catmPVclSegCCRangeStatusUpEnd are used. If the set of segment CC recovered PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of segment CC recovered PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclSegCCStatusUpTransition, catmPVclSegCCStatusUpStart, catmPVclSegCCStatusUpEnd will be used. In the case where the set of segment CC recovered PVCs contains both successive and singled out PVCs, both sets of objects will be used. If the set of End CC recovered PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclEndCCUpLowerRangeValue, catmPVclEndCCUpHigherRangeValue, catmPVclEndCCRangeStatusUpStart, catmPVclEndCCRangeStatusUpEnd are used. If the set of End CC recovered PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of End CC recovered PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclEndCCStatusUpTransition, catmPVclEndCCStatusUpStart, catmPVclEndCCStatusUpEnd will be used. In the case where the set of End CC recovered PVCs contains both successive and singled out PVCs, both sets of objects will be used. If the set of AIS/RDI recovered PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmPVclAISRDIUpLowerRangeValue, catmPVclAISRDIUpHigherRangeValue, catmPVclAISRDIRangeStatusUpStart, catmPVclAISRDIRangeStatusUpEnd are used. If the set of AIS/RDI recovered PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of AIS/RDI recovered PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclAISRDIStatusUpTransition, catmPVclAISRDIStatusUpStart, catmPVclAISRDIStatusUpEnd will be used. In the case where the set of AIS/RDI recovered PVCs contains both successive and singled out PVCs, both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 11 } VARIATION catmIntfPvcUp2Trap -- TRAP-TYPE -- OBJECTS { ifIndex, -- catmIntfCurrentlyDownToUpPVcls, -- atmVclVpi, -- atmVclVci, -- catmPVclCurRecoverTime, -- catmPVclPrevFailTime, -- catmPVclRecoveryReason, -- catmStatusChangePVclRangeIndex, -- catmUpPVclLowerRangeValue, -- catmUpPVclHigherRangeValue, -- catmUpPVclRangeStart, -- catmUpPVclRangeEnd, -- catmPrevDownPVclRangeStart, -- catmPrevDownPVclRangeEnd, -- catmPVclRangeRecoveryReason } DESCRIPTION "A catmIntfPvcUp2Trap signifies that atmVclOperStatus is detected as up on the PVC in the last PVC TRAP notification interval. If the set of atmVclOperStatus up PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmUpPVclLowerRangeValue, catmUpPVclHigherRangeValue, catmUpPVclRangeStart, catmUpPVclRangeEnd, catmPrevDownPVclRangeStart, catmPrevDownPVclRangeEnd, catmPVclRangeRecoveryReason are used. If the set of atmVclOperStatus up PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of atmVclOperStatus UP PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclCurRecoverTime, catmPVclPrevFailTime, catmPVclRecoveryReason will be used. In the case where the set of atmVclOperStatus up PVCs contains both successive and singled out PVCs, both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 12 } VARIATION catmIntfPvcDownTrap -- TRAP-TYPE -- OBJECTS { ifIndex, -- atmIntfPvcFailures, -- atmIntfCurrentlyFailingPVcls, -- atmVclVpi, -- atmVclVci, -- catmPVclCurFailTime, -- catmPVclPrevRecoverTime, -- catmPVclFailureReason, -- catmStatusChangePVclRangeIndex, -- catmDownPVclLowerRangeValue, -- catmDownPVclHigherRangeValue, -- catmDownPVclRangeStart, -- catmDownPVclRangeEnd, -- catmPrevUpPVclRangeStart, -- catmPrevUpPVclRangeEnd, -- catmPVclRangeFailureReason } DESCRIPTION "A catmIntfPvcDownTrap signifies atmVclOperStatus is detected as down on the PVC in the last PVC TRAP notification interval. If the set of atmVclOperStatus down PVCs contains successive VCIs, then the varbinds sent in this TRAP contains information about ranges representing these groups of PVCs. In this case, the atmVclVpi, catmStatusChangePVclRangeIndex, catmDownPVclLowerRangeValue, catmDownPVclHigherRangeValue, catmDownPVclRangeStart, catmDownPVclRangeEnd, catmPrevUpPVclRangeStart, catmPrevUpPVclRangeEnd, catmPVclRangeFailureReason are used. If the set of atmVclOperStatus down PVCs contains singled out PVCs (i.e. PVC with VPI1, VCI1 is contained in the set; but neither a PVC with VPI1 and VCI1 - 1 nor a PVC with VPI1 and VCI1 + 1 is contained in the set of atmVclOperStatus down PVCs) then the varbinds sent in this notification contains information about the individual PVCs. In this case, the atmVclVpi, atmVclVci, catmPVclCurFailTime, catmPVclPrevRecoverTime, catmPVclFailureReason will be used. In the case where the set of atmVclOperStatus down PVCs contains both successive and singled out PVCs, both sets of objects will be used." ::= { ciscoATMPVCTRAPExtnCapability 13 } END