#-MIBFILE: cpqwcrm.mib

CPQWCRM-MIB DEFINITIONS ::= BEGIN


compaq OBJECT IDENTIFIER ::= { enterprises 232 }
DisplayString ::=
	OCTET STRING

PhysAddress ::=
	OCTET STRING

mib-2 OBJECT IDENTIFIER ::= { mgmt 1 }
system OBJECT IDENTIFIER ::= { mib-2 1 }
sysName OBJECT IDENTIFIER ::= { system 5 }
mib-2 OBJECT IDENTIFIER ::= { mgmt 1 }
sysDescr OBJECT IDENTIFIER ::= { system 1 }
sysContact OBJECT IDENTIFIER ::= { system 4 }
sysLocation OBJECT IDENTIFIER ::= { system 6 }
cpqWcrm OBJECT IDENTIFIER ::= { compaq 167 }

cpqWcrmMibRev OBJECT IDENTIFIER ::= { cpqWcrm 1 }

cpqWcrmStatus OBJECT IDENTIFIER ::= { cpqWcrm 2 }

cpqWcrmStatusSensorInternal OBJECT IDENTIFIER ::= { cpqWcrmStatus 3 }

cpqWcrmStatusInternalSensors OBJECT IDENTIFIER ::= { cpqWcrmStatusSensorInternal 5 }

cpqWcrmStatusInternalOutputs OBJECT IDENTIFIER ::= { cpqWcrmStatusSensorInternal 6 }

cpqWcrmStatusInternalMsg OBJECT IDENTIFIER ::= { cpqWcrmStatusSensorInternal 7 }

cpqWcrmStatusSensorWaterCoolUnit OBJECT IDENTIFIER ::= { cpqWcrmStatus 4 }

cpqWcrmStatusWaterCoolUnitSensors OBJECT IDENTIFIER ::= { cpqWcrmStatusSensorWaterCoolUnit 5 }

cpqWcrmStatusWaterCoolUnitOutputs OBJECT IDENTIFIER ::= { cpqWcrmStatusSensorWaterCoolUnit 6 }

cpqWcrmStatusWaterCoolUnitMsg OBJECT IDENTIFIER ::= { cpqWcrmStatusSensorWaterCoolUnit 7 }

cpqWcrmSetup OBJECT IDENTIFIER ::= { cpqWcrm 3 }

cpqWcrmSetupGeneral OBJECT IDENTIFIER ::= { cpqWcrmSetup 1 }

cpqWcrmTimerTable1 OBJECT IDENTIFIER ::= { cpqWcrmSetupGeneral 8 }

cpqWcrmTrapControl OBJECT IDENTIFIER ::= { cpqWcrm 4 }

cpqWcrmTraps OBJECT IDENTIFIER ::= { cpqWcrmTrapControl 7 }

cpqWcrmControl OBJECT IDENTIFIER ::= { cpqWcrm 5 }

cpqWcrmMibMajRev OBJECT-TYPE
	SYNTAX INTEGER (1..65535)
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "The Major Revision level.
A change in the major revision level represents a major change
in the architecture of the MIB. A change in the major revision 
level may indicate a significant change in the information,
correct interpretation of data may require a MIB document
with the same major revision level."
	::= { cpqWcrmMibRev 1 }


cpqWcrmMibMinRev OBJECT-TYPE
	SYNTAX INTEGER (0..65535)
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "The Minor Revision level.
A change in the minor revision level may represent some minor
additional support, no changes to any pre-existing information
has occurred."
	::= { cpqWcrmMibRev 2 }


cpqWcrmMibCondition OBJECT-TYPE
	SYNTAX INTEGER {
	other(1),
	ok(2),
	degraded(3),
	failed(4),
	configChanged(5)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "The overall condition (status) of the system represented by
this MIB. 
(2) OK
(3) a minor problem, warning condition (yellow LED on Environmental Controller)
(4) a major problem (red LED on Environmental Controller)
(5) configuration of sensor units changed or
unit detected (red/yellow/green LED on Environmental Controller)"
	::= { cpqWcrmMibRev 3 }


cpqWcrmStatusDeviceEnvironmentalController OBJECT-TYPE
	SYNTAX INTEGER {
	failed(1),
	ok(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "General Status of Environmental Controller unit itself
(1) failed
(2) OK"
	::= { cpqWcrmStatus 1 }


cpqWcrmUnitsConnected OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Number of sensor units connected to the Environmental Controller, Port 1 to 2"
	::= { cpqWcrmStatus 2 }


cpqWcrmURL OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..80))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "URL of the management interface in the format http[s]://ipaddr[:port#][/page]"
	::= { cpqWcrmStatus 7 }


cpqWcrmInternalTypeOfDevice OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	unitWcrm(2),
	unitIO(3)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Type of sensor unit connected to port 1"
	::= { cpqWcrmStatusSensorInternal 1 }


cpqWcrmInternalText OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..10))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Descriptional text for sensor unit connected to port 1"
	::= { cpqWcrmStatusSensorInternal 2 }


cpqWcrmInternalSerial OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Serialnumber of sensor unit connected to port 1"
	::= { cpqWcrmStatusSensorInternal 3 }


cpqWcrmInternalStatus OBJECT-TYPE
	SYNTAX INTEGER {
	ok(1),
	error(2),
	changed(3),
	reset(4),
	timeout(5),
	detected(6),
	notAvail(7),
	lowPower(8)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "General Status sensor unit connected to port 1
(1) OK
(2) error, e. g. value overflow
(3) configuration of sensor unit has changed, confirmation required
(4) reset from sensor unit to confirm configuration changes
(5) timeout of sensor unit, confirmation required to unload this unit
(6) sensor unit detected, needs to be confirmed
(7) unit is not available
(8) supply voltage is too low"
	::= { cpqWcrmStatusSensorInternal 4 }


cpqWcrmInternalNumberOfSensors OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Number of sensors connected to sensor unit 1"
	::= { cpqWcrmStatusInternalSensors 1 }


cpqWcrmInternalSensorTable OBJECT-TYPE
	SYNTAX SEQUENCE OF CpqWcrmInternalSensorEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Headline of sensor table"
	::= { cpqWcrmStatusInternalSensors 2 }


cpqWcrmInternalSensorEntry OBJECT-TYPE
	SYNTAX CpqWcrmInternalSensorEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Entries of sensor table"
	INDEX { internalSensorIndex  }

	::= { cpqWcrmInternalSensorTable 1 }

cpqWcrmInternalSensorEntry ::=
	SEQUENCE {
		internalSensorIndex INTEGER,
		internalSensorType INTEGER,
		internalSensorText DisplayString,
		internalSensorStatus INTEGER,
		internalSensorValue INTEGER,
		internalSensorSetHigh INTEGER,
		internalSensorSetLow INTEGER,
		internalSensorSetWarn INTEGER
		}

internalSensorIndex OBJECT-TYPE
	SYNTAX INTEGER (1..65535)
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Index for the list of value entries. Its value ranges
between 1 and the value of cpqWcrmInternalNumberOfSensors."
	::= { cpqWcrmInternalSensorEntry 1 }


internalSensorType OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	failure(2),
	overflow(3),
	access(4),
	vibration(5),
	motion(6),
	smoke(7),
	airFlow(8),
	type6(9),
	temperature(10),
	current4to20(11),
	humidity(12),
	userNO(13),
	userNC(14),
	voltOK(17),
	voltage(18),
	fanOK(19),
	leakage(20)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Type of sensor which is connected to internal sensor to sensor[internalSensorIndex]
1:        no sensor connected
2:        sensor failure
3:        value overflow
4:        sensor type 1, access sensor
5:        sensor type 2, vibration sensor
6:        sensor type 3, motion sensor
7:        sensor type 4, smoke sensor
8:        sensor type 5, air flow sensor
9:        sensor type 6, reserved
10:       sensor type 7, temperature sensor
11:       sensor type 8, 4..20mA sensor
12:       sensor type 9, humidity sensor  
13:       user sensor with normally opened contact
14:       user sensor with normally closed contact
15:       door locked sensor from locking device
16:       remote unlock sensor (e.g. external keypad)
17:       voltage sensor, indicates status of main voltage (OK, NOK)
18:	voltage value
19:	fan status, from Environmental Controller-FAS-Unit
20:	leakage sensor"
	::= { cpqWcrmInternalSensorEntry 2 }


internalSensorText OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..20))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Descriptional text for each sensor (entry in the table)"
	::= { cpqWcrmInternalSensorEntry 3 }


internalSensorStatus OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	lost(2),
	changed(3),
	ok(4),
	off(5),
	on(6),
	warning(7),
	tooLow(8),
	tooHigh(9)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Actual status of the sensor"
	::= { cpqWcrmInternalSensorEntry 4 }


internalSensorValue OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Value of sensor"
	::= { cpqWcrmInternalSensorEntry 5 }


internalSensorSetHigh OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Value for high setpoint of sensor"
	::= { cpqWcrmInternalSensorEntry 6 }


internalSensorSetLow OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Value for low setpoint of sensor,
also used as alarm delay"
	::= { cpqWcrmInternalSensorEntry 7 }


internalSensorSetWarn OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Value for warning setpoint of sensor, 
also used as fan threshold"
	::= { cpqWcrmInternalSensorEntry 8 }


cpqWcrmInternalNumberOfOutputs OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Number of outputs available on internal sensor"
	::= { cpqWcrmStatusInternalOutputs 1 }


cpqWcrmInternalOutputTable OBJECT-TYPE
	SYNTAX SEQUENCE OF CpqWcrmInternalOutputEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Headline of output table"
	::= { cpqWcrmStatusInternalOutputs 2 }


cpqWcrmInternalOutputEntry OBJECT-TYPE
	SYNTAX CpqWcrmInternalOutputEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Entries of output table"
	INDEX { internalOutputIndex  }

	::= { cpqWcrmInternalOutputTable 1 }

cpqWcrmInternalOutputEntry ::=
	SEQUENCE {
		internalOutputIndex INTEGER,
		internalOutputType INTEGER,
		internalOutputText DisplayString,
		internalOutputStatus INTEGER,
		internalOutputValue INTEGER,
		internalOutputSet INTEGER,
		internalOutputConfig INTEGER,
		internalOutputDelay INTEGER,
		internalOutputTimeoutAction INTEGER
		}

internalOutputIndex OBJECT-TYPE
	SYNTAX INTEGER (1..65535)
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Index for the list of output entries. Its value ranges
between 1 and the value of cpqWcrmInternalNumberOfOutputs."
	::= { cpqWcrmInternalOutputEntry 1 }


internalOutputType OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	failure(2),
	overflow(3),
	universalOut(4),
	powerOut(5)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Type of output which is connected to internal sensor to output[internalOutputIndex]
1:        no output connected
2:        output failure
3:        value overflow
4:        output type 6, universal relay output
5:        output type 8, power output"
	::= { cpqWcrmInternalOutputEntry 2 }


internalOutputText OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..20))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Descriptional text for each output (entry in the table)"
	::= { cpqWcrmInternalOutputEntry 3 }


internalOutputStatus OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	lost(2),
	changed(3),
	ok(4),
	off(5),
	on(6),
	setOff(7),
	setOn(8)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Actual status of the output"
	::= { cpqWcrmInternalOutputEntry 4 }


internalOutputValue OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Value for output"
	::= { cpqWcrmInternalOutputEntry 5 }


internalOutputSet OBJECT-TYPE
	SYNTAX INTEGER {
	off(1),
	on(2),
	lock(3),
	unlock(4),
	unlockDelay(5)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Command for output"
	::= { cpqWcrmInternalOutputEntry 6 }


internalOutputConfig OBJECT-TYPE
	SYNTAX INTEGER {
	disRemote(1),
	enRemote(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Configuration for output
1: 	disable remote control (e.g. keypad)
2: 	enable remote control "
	::= { cpqWcrmInternalOutputEntry 7 }


internalOutputDelay OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Unsigned Value for delay, 
after this time the output will fall into the previous state"
	::= { cpqWcrmInternalOutputEntry 8 }


internalOutputTimeoutAction OBJECT-TYPE
	SYNTAX INTEGER {
	stay(1),
	off(2),
	on(3)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "State for output if timeout (RS422) occurs"
	::= { cpqWcrmInternalOutputEntry 9 }


cpqWcrmInternalNumberOfMsgs OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Number of messages that can be created with internal sensor"
	::= { cpqWcrmStatusInternalMsg 1 }


cpqWcrmInternalMsgTable OBJECT-TYPE
	SYNTAX SEQUENCE OF CpqWcrmInternalMsgEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Headline of message table"
	::= { cpqWcrmStatusInternalMsg 2 }


cpqWcrmInternalMsgEntry OBJECT-TYPE
	SYNTAX CpqWcrmInternalMsgEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Entries of message table"
	INDEX { internalMsgIndex  }

	::= { cpqWcrmInternalMsgTable 1 }

cpqWcrmInternalMsgEntry ::=
	SEQUENCE {
		internalMsgIndex INTEGER,
		internalMsgText DisplayString,
		internalMsgStatus INTEGER,
		internalMsgRelay INTEGER,
		internalMsgBeeper INTEGER,
		internalMsgTrap1 INTEGER,
		internalMsgTrap2 INTEGER,
		internalMsgTrap3 INTEGER,
		internalMsgTrap4 INTEGER,
		internalMsgReset INTEGER
		}

internalMsgIndex OBJECT-TYPE
	SYNTAX INTEGER (1..65535)
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Index for the list of message entries. Its value ranges
between 1 and the value of cpqWcrmInternalNumberOfMsgs."
	::= { cpqWcrmInternalMsgEntry 1 }


internalMsgText OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..20))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Descriptional text for each message (entry in the table)"
	::= { cpqWcrmInternalMsgEntry 2 }


internalMsgStatus OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	configChanged(2),
	error(3),
	ok(4),
	alarm(5),
	warning(6),
	tooLow(7),
	tooHigh(8),
	setOff(9),
	setOn(10)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Actual message status
1: not available
2: configuration has changed (sensor new, changed, lost)
3: error
4: OK
5: alarm, e.g. smoke, vibration...
6: warning of analog value, value reached warning threshold
7: analog value too low, value reached low threshold
8: analog value too high, value reached high threshold
9: output is set to ON
10: output is set to OFF"
	::= { cpqWcrmInternalMsgEntry 3 }


internalMsgRelay OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Setup of Alarm relay for this message/alarm
1:        no switching of alarm relay             
2:        switching of alarm relay"
	::= { cpqWcrmInternalMsgEntry 4 }


internalMsgBeeper OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Setup of Alarm beeper for this alarm
1:        no audible alarm
2:        audible alarm"
	::= { cpqWcrmInternalMsgEntry 5 }


internalMsgTrap1 OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Trap receiver 1 activated"
	::= { cpqWcrmInternalMsgEntry 6 }


internalMsgTrap2 OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Trap receiver 2 activated"
	::= { cpqWcrmInternalMsgEntry 7 }


internalMsgTrap3 OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Trap receiver 3 activated"
	::= { cpqWcrmInternalMsgEntry 8 }


internalMsgTrap4 OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Trap receiver 4 and Event Logging activated"
	::= { cpqWcrmInternalMsgEntry 9 }


internalMsgReset OBJECT-TYPE
	SYNTAX INTEGER {
	auto(1),
	manual(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Reset of this alarm
1:		auto
2:		manual, alarm needs confirmation, e. g. with 'C' key"
	::= { cpqWcrmInternalMsgEntry 10 }


cpqWcrmWaterCoolUnitTypeOfDevice OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	unitWcrm(2),
	unitIO(3)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Type of sensor unit connected to port 2"
	::= { cpqWcrmStatusSensorWaterCoolUnit 1 }


cpqWcrmWaterCoolUnitText OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..10))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Descriptional text for sensor unit connected to port 2"
	::= { cpqWcrmStatusSensorWaterCoolUnit 2 }


cpqWcrmWaterCoolUnitSerial OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Serialnumber of sensor unit connected to port 2"
	::= { cpqWcrmStatusSensorWaterCoolUnit 3 }


cpqWcrmWaterCoolUnitStatus OBJECT-TYPE
	SYNTAX INTEGER {
	ok(1),
	error(2),
	changed(3),
	reset(4),
	timeout(5),
	detected(6),
	notAvail(7),
	lowPower(8)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "General Status sensor unit connected to port 2
(1) OK
(2) error
(3) configuration of sensor unit has changed, confirmation required
(4) reset from sensor unit to confirm configuration changes
(5) timeout of sensor unit, confirmation required
(6) sensor unit detected, needs to be confirmed
(8) supply voltage is too low"
	::= { cpqWcrmStatusSensorWaterCoolUnit 4 }


cpqWcrmWaterCoolUnitNumberOfSensors OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Number of sensors connected to water cool unit"
	::= { cpqWcrmStatusWaterCoolUnitSensors 1 }


cpqWcrmWaterCoolUnitSensorTable OBJECT-TYPE
	SYNTAX SEQUENCE OF CpqWcrmWaterCoolUnitSensorEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Headline of sensor table"
	::= { cpqWcrmStatusWaterCoolUnitSensors 2 }


cpqWcrmWaterCoolUnitSensorEntry OBJECT-TYPE
	SYNTAX CpqWcrmWaterCoolUnitSensorEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Entries of sensor table"
	INDEX { waterCoolUnitSensorIndex  }

	::= { cpqWcrmWaterCoolUnitSensorTable 1 }

cpqWcrmWaterCoolUnitSensorEntry ::=
	SEQUENCE {
		waterCoolUnitSensorIndex INTEGER,
		waterCoolUnitSensorType INTEGER,
		waterCoolUnitSensorText DisplayString,
		waterCoolUnitSensorStatus INTEGER,
		waterCoolUnitSensorValue INTEGER,
		waterCoolUnitSensorSetHigh INTEGER,
		waterCoolUnitSensorSetLow INTEGER,
		waterCoolUnitSensorSetWarn INTEGER
		}

waterCoolUnitSensorIndex OBJECT-TYPE
	SYNTAX INTEGER (1..65535)
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Index for the list of value entries. Its value ranges
between 1 and the value of cpqWcrmWaterCoolUnitNumberOfSensors."
	::= { cpqWcrmWaterCoolUnitSensorEntry 1 }


waterCoolUnitSensorType OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	failure(2),
	overflow(3),
	tempIn(4),
	tempOut(5),
	heatFlow(6),
	alarm(7),
	warning(8),
	rpmFan1(9),
	rpmFan2(10),
	rpmFan3(11),
	fanSpeed(12),
	tempIn1(13),
	tempOut1(14),
	tempIn2(15),
	tempOut2(16),
	tempIn3(17),
	tempOut3(18),
	tempWaterIn(19),
	tempWaterOut(20),
	waterFlow(21),
	valve(22),
	status(23),
	condensateDuration(24),
	condensateCycles(25),
	rpmFan4(26),
	rpmFan5(27),
	rpmFan6(28),
	transfSwitch(29),
	valveActValue(30)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Type of sensor which is connected to internal sensor to sensor[internalSensorIndex]
1:        no sensor connected
2:        sensor failure
3:        value overflow
4:        average temperature of air inlet to rack, average or max/min from each HEX
5:        average temperature of air outlet from rack, average or max/min from each HEX
6:        heatflow sensor
7:        alarm: 
Bit 0: Leakage
Bit 1: IIC Failure
8:        warning:
Bit 0..2:   Fan Tach 1..3
Bit 3,4:    Temp. sensor HEX1 In,Out
Bit 5,6:    Temp. sensor HEX2 In,Out
Bit 7,8:    Temp. sensor HEX3 In,Out
Bit 9:      Air temp. sensor
Bit 10..12: IIC failure, HEX1..3
Bit 13:     Waterflow low
Bit 14,15:  Watertemp. In,Out
Bit 16:	    Waterflow sensor fail.
Bit 17:     Magnetic valve fail.
Bit 18:     Leakdetector fail.
Bit 19:     Uneven heat load
Bit 20:     Condensation Pump Cycles > Max
Bit 21:	    Condensation Pump Running Time > Max
9:        rpm speed of Fan1
10:       rpm speed of Fan2
11:       rpm speed of Fan3
12:       fanSpeed setpoint, calculated from average temperatures 
13:       temperature air inlet to rack, HEX 1
14:       temperature air outlet from rack, HEX 1
15:       temperature air inlet to rack, HEX 1
16:       temperature air outlet from rack, HEX 1
17:       temperature air inlet to rack, HEX 1
18:	temperature air outlet from rack, HEX 1
19:	water temperature In
20:       water temperature Out
21:	water Flow
22:	water valve status: MCS:0: Valve opened, 1: valve closed; MCSS: valve setpoint (%)
23:	status: Bit 0..Bit 2: fan module 1..3 available
Bit 3: water module available
24:	condensation pump number of seconds on counter (last operating time) 
25:	condensation pump on/off cycle counter
26:       rpm speed of Fan4
27:       rpm speed of Fan5
28:       rpm speed of Fan6
29:	status of transfer switch, 1=AC1, 2=AC2, 3=AC1 and AC2
30:	water valve actual value (%)"
	::= { cpqWcrmWaterCoolUnitSensorEntry 2 }


waterCoolUnitSensorText OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..20))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Descriptional text for each sensor (entry in the table)"
	::= { cpqWcrmWaterCoolUnitSensorEntry 3 }


waterCoolUnitSensorStatus OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	lost(2),
	changed(3),
	ok(4),
	off(5),
	on(6),
	warning(7),
	tooLow(8),
	tooHigh(9)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Actual status of the sensor"
	::= { cpqWcrmWaterCoolUnitSensorEntry 4 }


waterCoolUnitSensorValue OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Value of sensor added to traps, msg index also added (waterCoolUnitMsgIndex)

If msg index = 1, 5 or 6
This value represents the actual Server Intake Temperature.

If msg index = 2:
This value represents the bit coded warning condition
Bit 0:   Top Fan Module Failed
Bit 1:   Middle Fan Module Failed
Bit 2:   Bottom Fan Module Failed
Bit 3:   Top HEX Intake Air Temperature Sensor to Server Failed
Bit 4:   Top HEX Exhaust Air Temperature Sensor from Server Failed
Bit 5:   Middle HEX Intake Air Temperature Sensor to Server Failed
Bit 6:   Middle HEX Exhaust Air Temperature Sensor from Server Failed
Bit 7:   Bottom HEX Intake Air Temperature Sensor to Server Failed
Bit 8:   Bottom HEX Exhaust Air Temperature Sensor from Server Failed
Bit 9:   Air Temperature Sensor Failed
Bit 10:  Top Fan not installed
Bit 11:  Middle Fan not installed
Bit 12:  Bottom Fan not installed
Bit 13:  Waterflow low
Bit 14:  Water Unit Temperature Input Out of Range
Bit 15:  Water Unit Temperature Output Out of Range
Bit 16:	 Waterflow Sensor Value Out of Range
Bit 17:  Water Valve Failed
Bit 18:  Leakdetector Failed
Bit 19:  Heat Load Warning
Bit 20:  The Condensation Pump has exceeded the max. number of cycles
Bit 21:	 The Condensation Pump has exceeded the max. Running Time

If msg index = 3:
This value represents the bit coded alarm condition
Bit 0:	 Leakage Detected
Bit 1:   Comm. Failure IIC"
	::= { cpqWcrmWaterCoolUnitSensorEntry 5 }


waterCoolUnitSensorSetHigh OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Value for high setpoint of sensor"
	::= { cpqWcrmWaterCoolUnitSensorEntry 6 }


waterCoolUnitSensorSetLow OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Value for low setpoint of sensor,
also used as alarm delay"
	::= { cpqWcrmWaterCoolUnitSensorEntry 7 }


waterCoolUnitSensorSetWarn OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Value for warning setpoint of sensor,
also used as fan threshold"
	::= { cpqWcrmWaterCoolUnitSensorEntry 8 }


cpqWcrmWaterCoolUnitNumberOfOutputs OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Number of outputs available on sensor water cool unit"
	::= { cpqWcrmStatusWaterCoolUnitOutputs 1 }


cpqWcrmWaterCoolUnitOutputTable OBJECT-TYPE
	SYNTAX SEQUENCE OF CpqWcrmWaterCoolUnitOutputEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Headline of output table"
	::= { cpqWcrmStatusWaterCoolUnitOutputs 2 }


cpqWcrmWaterCoolUnitOutputEntry OBJECT-TYPE
	SYNTAX CpqWcrmWaterCoolUnitOutputEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Entries of output table"
	INDEX { waterCoolUnitOutputIndex  }

	::= { cpqWcrmWaterCoolUnitOutputTable 1 }

cpqWcrmWaterCoolUnitOutputEntry ::=
	SEQUENCE {
		waterCoolUnitOutputIndex INTEGER,
		waterCoolUnitOutputType INTEGER,
		waterCoolUnitOutputText DisplayString,
		waterCoolUnitOutputStatus INTEGER,
		waterCoolUnitOutputValue INTEGER,
		waterCoolUnitOutputSet INTEGER,
		waterCoolUnitOutputConfig INTEGER,
		waterCoolUnitOutputDelay INTEGER,
		waterCoolUnitOutputTimeoutAction INTEGER
		}

waterCoolUnitOutputIndex OBJECT-TYPE
	SYNTAX INTEGER (1..65535)
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Index for the list of output entries. Its value ranges
between 1 and the value of cpqWcrmWaterCoolUnitNumberOfOutputs."
	::= { cpqWcrmWaterCoolUnitOutputEntry 1 }


waterCoolUnitOutputType OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	failure(2),
	overflow(3),
	setpoint(4),
	hysteresis(5),
	command(6),
	controlMode(7),
	fanSpeedMin(8),
	dTmin(9),
	dTmax(10),
	cpWatert(11),
	setHeatload(12),
	setEdoFlow(13),
	setEdoHeat(14),
	setCondCycles(15),
	setCondRun(16),
	doorControl(17),
	pidContrKP(18),
	pidContrKI(19),
	pidContrKD(20),
	pidSampleTime(21)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Type of output which is connected to water cool unit to output[waterCoolUnitOutputIndex]
1:        no output connected
2:        output failure                         
3:        value overflow
4:        water valve setpoint
5:        water valve hysteresis
6:        command for manual control
7:        Flow Meter Model, 0=SIKA, 1=Chemline
8:        minimum fan speed
9:        min delta T, used for fan control
10:       max delta T, used for fan control 
11:  	specific heat capacity
12:	setpoint heatload warning
13:	setpoint Water Flow Loss Emergency Door Opening
14:	setpoint High Temperature Emergency Door Opening
15:	setpoint Condensation Pump Cycles (Warning)
16:	setpoint Condensation Pump Running Time (Warning)
17:	command for door opening, 0=lock door, 1=unlock door
18:	KP parameter for PID controller
19:	KI parameter for PID controller
20:	KD parameter for PID controller
21:	sampling time PID controller"
	::= { cpqWcrmWaterCoolUnitOutputEntry 2 }


waterCoolUnitOutputText OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..20))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Descriptional text for each output (entry in the table)"
	::= { cpqWcrmWaterCoolUnitOutputEntry 3 }


waterCoolUnitOutputStatus OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	lost(2),
	changed(3),
	ok(4),
	off(5),
	on(6),
	setOff(7),
	setOn(8)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Actual status of the output"
	::= { cpqWcrmWaterCoolUnitOutputEntry 4 }


waterCoolUnitOutputValue OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Signed value for output"
	::= { cpqWcrmWaterCoolUnitOutputEntry 5 }


waterCoolUnitOutputSet OBJECT-TYPE
	SYNTAX INTEGER {
	off(1),
	on(2),
	lock(3),
	unlock(4),
	unlockDelay(5)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Command for output"
	::= { cpqWcrmWaterCoolUnitOutputEntry 6 }


waterCoolUnitOutputConfig OBJECT-TYPE
	SYNTAX INTEGER {
	disRemote(1),
	enRemote(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Configuration for output
1: 	disable remote control (e.g. keypad)
2: 	enable remote control "
	::= { cpqWcrmWaterCoolUnitOutputEntry 7 }


waterCoolUnitOutputDelay OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Unsigned Value for delay, 
after this time the output will fall into the previous state"
	::= { cpqWcrmWaterCoolUnitOutputEntry 8 }


waterCoolUnitOutputTimeoutAction OBJECT-TYPE
	SYNTAX INTEGER {
	stay(1),
	off(2),
	on(3)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "State for output if timeout (RS422) occurs"
	::= { cpqWcrmWaterCoolUnitOutputEntry 9 }


cpqWcrmWaterCoolUnitNumberOfMsgs OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Number of alarms that can be created with water cool unit"
	::= { cpqWcrmStatusWaterCoolUnitMsg 1 }


cpqWcrmWaterCoolUnitMsgTable OBJECT-TYPE
	SYNTAX SEQUENCE OF CpqWcrmWaterCoolUnitMsgEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Headline of message table"
	::= { cpqWcrmStatusWaterCoolUnitMsg 2 }


cpqWcrmWaterCoolUnitMsgEntry OBJECT-TYPE
	SYNTAX CpqWcrmWaterCoolUnitMsgEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Entries of message table"
	INDEX { waterCoolUnitMsgIndex  }

	::= { cpqWcrmWaterCoolUnitMsgTable 1 }

cpqWcrmWaterCoolUnitMsgEntry ::=
	SEQUENCE {
		waterCoolUnitMsgIndex INTEGER,
		waterCoolUnitMsgText DisplayString,
		waterCoolUnitMsgStatus INTEGER,
		waterCoolUnitMsgRelay INTEGER,
		waterCoolUnitMsgBeeper INTEGER,
		waterCoolUnitMsgTrap1 INTEGER,
		waterCoolUnitMsgTrap2 INTEGER,
		waterCoolUnitMsgTrap3 INTEGER,
		waterCoolUnitMsgTrap4 INTEGER,
		waterCoolUnitMsgReset INTEGER
		}

waterCoolUnitMsgIndex OBJECT-TYPE
	SYNTAX INTEGER (1..65535)
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Index for the list of alarm entries. Its value ranges
between 1 and the value of cpqWcrmWaterCoolUnitNumberOfMsgs."
	::= { cpqWcrmWaterCoolUnitMsgEntry 1 }


waterCoolUnitMsgText OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..20))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Descriptional text for each message (entry in the table)"
	::= { cpqWcrmWaterCoolUnitMsgEntry 2 }


waterCoolUnitMsgStatus OBJECT-TYPE
	SYNTAX INTEGER {
	notAvail(1),
	configChanged(2),
	error(3),
	ok(4),
	alarm(5),
	warning(6),
	tooLow(7),
	tooHigh(8),
	setOff(9),
	setOn(10)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Actual message status
4: OK
5: alarm
6: warning
7: analog value too low, value reached low threshold
8: analog value too high, value reached high threshold"
	::= { cpqWcrmWaterCoolUnitMsgEntry 3 }


waterCoolUnitMsgRelay OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Setup of Alarm relay for this alarm
2:        no switching of alarm relay             
1:        switching of alarm relay"
	::= { cpqWcrmWaterCoolUnitMsgEntry 4 }


waterCoolUnitMsgBeeper OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Setup of Alarm beeper for this alarm
2:        no audible alarm
1:        audible alarm"
	::= { cpqWcrmWaterCoolUnitMsgEntry 5 }


waterCoolUnitMsgTrap1 OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Trap receiver 1 activated"
	::= { cpqWcrmWaterCoolUnitMsgEntry 6 }


waterCoolUnitMsgTrap2 OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Trap receiver 2 activated"
	::= { cpqWcrmWaterCoolUnitMsgEntry 7 }


waterCoolUnitMsgTrap3 OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Trap receiver 3 activated"
	::= { cpqWcrmWaterCoolUnitMsgEntry 8 }


waterCoolUnitMsgTrap4 OBJECT-TYPE
	SYNTAX INTEGER {
	disable(1),
	enable(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Trap receiver 4 and Event Logging activated"
	::= { cpqWcrmWaterCoolUnitMsgEntry 9 }


waterCoolUnitMsgReset OBJECT-TYPE
	SYNTAX INTEGER {
	auto(1),
	manual(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Reset of this alarm
1:		auto
2:		manual, alarm needs confirmation, e. g. with 'C' key"
	::= { cpqWcrmWaterCoolUnitMsgEntry 10 }


cpqWcrmSetTempUnit OBJECT-TYPE
	SYNTAX INTEGER {
	celsius(1),
	fahrenheit(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Unit of all temperature values and setpoints, Celsius or Fahrenheit"
	::= { cpqWcrmSetupGeneral 1 }


cpqWcrmSetBeeper OBJECT-TYPE
	SYNTAX INTEGER {
	off(1),
	on(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Audible alarm in Environmental Controller unit:
(2): beeper is on
(1): beeper is off (general)"
	::= { cpqWcrmSetupGeneral 2 }


cpqWcrmResetRelay OBJECT-TYPE
	SYNTAX INTEGER {
	disabled(1),
	enabled(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Enable or disable acknowledging currently active alarm relay 
(with 'C' on Environmental Controller)."
	::= { cpqWcrmSetupGeneral 3 }


cpqWcrmLogicRelay OBJECT-TYPE
	SYNTAX INTEGER {
	closeAtAlarm(1),
	openAtAlarm(2),
	off(3)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Logic of alarm relay: 
(1) Relay will pick up in case of an alarm
(2) Relay will release in case of an alarm
(3) Relay off (general)"
	::= { cpqWcrmSetupGeneral 4 }


cpqWcrmWebAccess OBJECT-TYPE
	SYNTAX INTEGER {
	viewOnly(1),
	fullAccess(2),
	off(3)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Web access via HTTP: 
(1) view only
(2) full Access, read and set
(3) Web disabled (general)"
	::= { cpqWcrmSetupGeneral 5 }


cpqWcrmSetupDate OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..10))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "actual Date in format DD.MM.YYYY"
	::= { cpqWcrmSetupGeneral 6 }


cpqWcrmSetupTime OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..8))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "actual Time in format HH:MM:SS, HH (0-23), MM (0-59), SS (0-59)"
	::= { cpqWcrmSetupGeneral 7 }


cpqWcrmTimerNumber OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Number of value-table entries=number of outlets available on this unit"
	::= { cpqWcrmTimerTable1 1 }


cpqWcrmTimerTable OBJECT-TYPE
	SYNTAX SEQUENCE OF CpqWcrmTimerEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Headline of status-table"
	::= { cpqWcrmTimerTable1 2 }


cpqWcrmTimerEntry OBJECT-TYPE
	SYNTAX CpqWcrmTimerEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Entries of timer-table"
	INDEX { cpqWcrmTimerIndex  }

	::= { cpqWcrmTimerTable 1 }

cpqWcrmTimerEntry ::=
	SEQUENCE {
		cpqWcrmTimerIndex INTEGER,
		cpqWcrmTimerStatus INTEGER,
		cpqWcrmTimerDayOfWeek INTEGER,
		cpqWcrmTimeOn DisplayString,
		cpqWcrmTimeOff DisplayString,
		cpqWcrmTimeControl INTEGER,
		cpqWcrmTimerFunction INTEGER
		}

cpqWcrmTimerIndex OBJECT-TYPE
	SYNTAX INTEGER (1..65535)
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Index for the list of timer entries. Its value ranges
between 1 and the value of cpqWcrmTimerNumber."
	::= { cpqWcrmTimerEntry 1 }


cpqWcrmTimerStatus OBJECT-TYPE
	SYNTAX INTEGER {
	switchedOff(1),
	switchedOn(2),
	noTime(3)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Actual status of the timer"
	::= { cpqWcrmTimerEntry 2 }


cpqWcrmTimerDayOfWeek OBJECT-TYPE
	SYNTAX INTEGER {
	sun(1),
	mon(2),
	tue(3),
	wed(4),
	thu(5),
	fri(6),
	sat(7),
	sat-sun(8),
	mon-fri(9),
	mon-sun(10)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Selection of day of week for timer to switch"
	::= { cpqWcrmTimerEntry 3 }


cpqWcrmTimeOn OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..5))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Time to switch on current function, 
Format: HH:MM"
	::= { cpqWcrmTimerEntry 4 }


cpqWcrmTimeOff OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..5))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Time to switch off current function,
Format: HH:MM"
	::= { cpqWcrmTimerEntry 5 }


cpqWcrmTimeControl OBJECT-TYPE
	SYNTAX INTEGER {
	disabled(1),
	enabled(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Control via RTC"
	::= { cpqWcrmTimerEntry 6 }


cpqWcrmTimerFunction OBJECT-TYPE
	SYNTAX INTEGER {
	disTrapRec1(1),
	disTrapRec2(2),
	disTrapRec3(3),
	disTrapRec4(4),
	schedule1(5),
	schedule2(6),
	schedule3(7),
	schedule4(8)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Function which is controlled via timer
1-4: sending Traps to this Trap receiver will be disabled
5 - 8: scheduled alarm off"
	::= { cpqWcrmTimerEntry 7 }


cpqWcrmSetFlowUnit OBJECT-TYPE
	SYNTAX INTEGER {
	literMin(1),
	gallonMin(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Unit of Water Flow, Liter/min or Gallon/min"
	::= { cpqWcrmSetupGeneral 9 }


cpqWcrmTraptableNumber OBJECT-TYPE
	SYNTAX INTEGER
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Number of trapTable entries. The number of trap-receiver"
	::= { cpqWcrmTraps 1 }


cpqWcrmTrapTableTable OBJECT-TYPE
	SYNTAX SEQUENCE OF CpqWcrmTrapTableEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "A list of trap-receiver entries"
	::= { cpqWcrmTraps 2 }


cpqWcrmTrapTableEntry OBJECT-TYPE
	SYNTAX CpqWcrmTrapTableEntry
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Entries of trapTable"
	INDEX { trapIndex  }

	::= { cpqWcrmTrapTableTable 1 }

cpqWcrmTrapTableEntry ::=
	SEQUENCE {
		trapIndex INTEGER,
		trapStatus INTEGER,
		trapIPaddress DisplayString
		}

trapIndex OBJECT-TYPE
	SYNTAX INTEGER (1..65535)
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Index for the trap-receiver-table. Its value ranges between
1 and the value of traptableNumber "
	::= { cpqWcrmTrapTableEntry 1 }


trapStatus OBJECT-TYPE
	SYNTAX INTEGER {
	disabled(1),
	enabled(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Enable or disable trap receiver"
	::= { cpqWcrmTrapTableEntry 2 }


trapIPaddress OBJECT-TYPE
	SYNTAX DisplayString (SIZE(0..15))
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "IP-address of trap-receiver"
	::= { cpqWcrmTrapTableEntry 3 }


cpqWcrmResetUnit OBJECT-TYPE
	SYNTAX INTEGER {
	noReset(1),
	reset(2)
	}
	ACCESS read-only
	STATUS mandatory
	DESCRIPTION "Command to reset (acknowledge) alarms of Environmental Controller unit.
Setting to 'reset' (2) will have same result as pressing 'C' on Units.
Variable is automatically set back to 'noReset' (1)."
	::= { cpqWcrmControl 1 }


alarmSensorInternal TRAP-TYPE
	ENTERPRISE cpqWcrm
	VARIABLES { sysContact, sysName, sysLocation, internalMsgIndex, internalMsgText, internalMsgStatus, internalSensorValue, cpqWcrmURL }

	--#TYPE         "Internal sensor alarm"

	--#SUMMARY      "Location: %s, Alarm[%d]: %s, Status: %d, Actual Value: %d, from: %s, contact %s, URL %s"

	--#ARGUMENTS    { 2, 3, 4, 5, 6, 1, 0, 7}

	--#SEVERITY     MAJOR

	--#CATEGORY    "SYSTEM AND ENVIRONMENTAL"

	--#TIMEINDEX    99
DESCRIPTION "Internal Sensor Alarm"
	::= 1


alarmSensorWaterCoolUnit TRAP-TYPE
	ENTERPRISE cpqWcrm
	VARIABLES { sysContact, sysName, sysLocation, waterCoolUnitMsgIndex, waterCoolUnitMsgText, waterCoolUnitMsgStatus, waterCoolUnitSensorValue, cpqWcrmURL }

	--#TYPE         "Water cool unit sensor alarm"

	--#SUMMARY      "Location: %s, Alarm[%d]: %s, Status: %d, Actual Value: %d, from: %s, contact %s, URL %s"

	--#ARGUMENTS    { 2, 3, 4, 5, 6, 1, 0, 7}

	--#SEVERITY     MAJOR

	--#CATEGORY    "SYSTEM AND ENVIRONMENTAL"

	--#TIMEINDEX    99
DESCRIPTION "Water Cool Unit Sensor Alarm"
	::= 2


alarmInternal TRAP-TYPE
	ENTERPRISE cpqWcrm
	VARIABLES { sysContact, sysName, sysLocation, cpqWcrmInternalText, cpqWcrmInternalStatus, cpqWcrmURL }

	--#TYPE         "Internal unit alarm"

	--#SUMMARY      "Location: %s, Status: %s, from: %s, contact %s, URL %s"

	--#ARGUMENTS    { 2, 3, 1, 0, 5}

	--#SEVERITY     MAJOR

	--#CATEGORY    "SYSTEM AND ENVIRONMENTAL"

	--#TIMEINDEX    99
DESCRIPTION "Internal Unit Alarm"
	::= 5


alarmWaterCoolUnit TRAP-TYPE
	ENTERPRISE cpqWcrm
	VARIABLES { sysContact, sysName, sysLocation, cpqWcrmWaterCoolUnitText, cpqWcrmWaterCoolUnitStatus, cpqWcrmURL }

	--#TYPE         "Water cool unit alarm"

	--#SUMMARY      "Location: %s, Status: %s, from: %s, contact %s, URL %s"

	--#ARGUMENTS    { 2, 3, 1, 0, 5}

	--#SEVERITY     MAJOR

	--#CATEGORY    "SYSTEM AND ENVIRONMENTAL"

	--#TIMEINDEX    99
DESCRIPTION "Water Cool Unit System Alarm"
	::= 6


testTrap TRAP-TYPE
	ENTERPRISE cpqWcrm
	VARIABLES { sysContact, sysName, sysLocation, cpqWcrmURL }

	--#TYPE         "Test Trap"

	--#SUMMARY      "Location: %s, Test Trap from unit %s was sent, contact %s, URL %s"

	--#ARGUMENTS    { 2, 1, 0, 3}

	--#SEVERITY     INFORMATIONAL

	--#CATEGORY    "SYSTEM AND ENVIRONMENTAL"

	--#TIMEINDEX    99
DESCRIPTION "Test trap sent to a trap receiver to check proper reception of traps"
	::= 10

END